Date: Wed, 25 Aug 1999 12:36:22 +0200 From: Jesper Skriver <jesper@skriver.dk> To: freebsd-stable@freebsd.org Cc: Bill Paul <wpaul@FreeBSD.org> Subject: Re: xl0: no memory for rx list -- packet dropped Message-ID: <19990825123621.J10374@skriver.dk> In-Reply-To: <19990825121038.G10374@skriver.dk>; from Jesper Skriver on Wed, Aug 25, 1999 at 12:10:38PM %2B0200 References: <19990825121038.G10374@skriver.dk>
next in thread | previous in thread | raw e-mail | index | archive | help
On Wed, Aug 25, 1999 at 12:10:38PM +0200, Jesper Skriver wrote:
> We had a 3.2-STABLE from the 19th of August that hung with this on the
> console.
>
> I'm afraid I have no further info, DDB was compiled in, but I couldn't
> get into the kernel debugger ...
>
> Yes, I am preparing for a imminent death, as I have no real debugging
> information ;-)
I'll commit harakiri, don't bother.
From /var/log/messages:
Aug 25 04:45:54 gl-mie /kernel: xl0: transmission error: 90
Aug 25 04:45:54 gl-mie /kernel: xl0: tx underrun, increasing tx start threshold to 120 bytes
Aug 25 04:49:18 gl-mie /kernel: xl0: transmission error: 90
Aug 25 04:49:19 gl-mie /kernel: xl0: tx underrun, increasing tx start threshold to 180 bytes
Aug 25 04:51:42 gl-mie /kernel: xl0: transmission error: 90
Aug 25 04:51:43 gl-mie /kernel: xl0: tx underrun, increasing tx start threshold to 240 bytes
Aug 25 05:47:09 gl-mie /kernel: xl0: transmission error: 90
Aug 25 05:47:09 gl-mie /kernel: xl0: tx underrun, increasing tx start threshold to 300 bytes
Aug 25 08:32:16 gl-mie /kernel: Out of mbuf clusters - adjust NMBCLUSTERS or increase maxusers!
Aug 25 08:32:16 gl-mie /kernel: xl0: no memory for rx list -- packet dropped!
Aug 25 08:32:48 gl-mie last message repeated 33 times
dmesg:
Copyright (c) 1992-1999 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.2-STABLE #0: Thu Aug 19 11:14:57 CEST 1999
root@remie.nms.tele.dk:/usr/src/sys/compile/HP
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 300683203 Hz
CPU: Pentium II (300.68-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x634 Stepping = 4
Features=0x80fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 67108864 (65536K bytes)
config> q
avail memory = 62763008 (61292K bytes)
Preloaded elf kernel "kernel" at 0xc0262000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc026209c.
eisa0: <HWPc141 (System Board)>
Probing for devices on the EISA bus
Probing for devices on PCI bus 0:
Correcting Natoma config for non-SMP
chip0: <Intel 82440FX (Natoma) PCI and memory controller> rev 0x02 on pci0.0.0
xl0: <3Com 3c905B-TX Fast Etherlink XL> rev 0x24 int a irq 9 on pci0.7.0
xl0: Ethernet address: 00:10:4b:6b:ce:40
xl0: autoneg complete, link status good (half-duplex, 100Mbps)
chip1: <PCI to PCI bridge (vendor=1011 device=0021)> rev 0x02 on pci0.8.0
chip2: <Intel 82375EB PCI-EISA bridge> rev 0x15 on pci0.9.0
ahc0: <Adaptec aic7880 Ultra SCSI adapter> rev 0x00 int a irq 15 on pci0.10.0
ahc0: Using left over BIOS settings
ahc0: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
ahc1: <Adaptec aic7880 Ultra SCSI adapter> rev 0x00 int a irq 15 on pci0.11.0
ahc1: Using left over BIOS settings
ahc1: aic7880 Wide Channel A, SCSI Id=7, 16/255 SCBs
Probing for devices on PCI bus 1:
ahc2: <Adaptec 2940 Ultra2 SCSI adapter> rev 0x00 int a irq 11 on pci1.3.0
ahc2: aic7890/91 Wide Channel A, SCSI Id=7, 16/255 SCBs
Probing for PnP devices:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
atkbdc0 at 0x60-0x6f on motherboard
atkbd0 irq 1 on isa
sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
ppc0 at 0x378 irq 7 flags 0x40 on isa
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
ppi0: <generic parallel i/o> on ppbus 0
plip0: <PLIP network interface> on ppbus 0
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
Waiting 5 seconds for SCSI devices to settle
pass0 at ahc0 bus 0 target 5 lun 0
pass0: <TOSHIBA CD-ROM XM-5701TA 0787> Removable CD-ROM SCSI-2 device
pass0: 10.000MB/s transfers (10.000MHz, offset 8)
da0 at ahc2 bus 0 target 0 lun 0
da0: <Eurolog Voyager3000 0131> Fixed Direct Access SCSI-2 device
da0: 20.000MB/s transfers (20.000MHz, offset 16), Tagged Queueing Enabled
da0: 70076MB (143515904 512 byte sectors: 255H 63S/T 8933C)
changing root device to da0s1a
WARNING: / was not properly dismounted
xl0: selecting MII, 100Mbps, half duplex
xl0: selecting MII, 100Mbps, full duplex
/Jesper
--
Jesper Skriver (JS4261-RIPE), Network manager
Tele Danmark DataNet, IP section (AS3292)
One Unix to rule them all, One Resolver to find them,
One IP to bring them all and in the zone to bind them.
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-stable" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?19990825123621.J10374>