From owner-freebsd-bugs Thu Jul 27 16:39:16 1995 Return-Path: bugs-owner Received: (from majordom@localhost) by freefall.cdrom.com (8.6.11/8.6.6) id QAA13678 for bugs-outgoing; Thu, 27 Jul 1995 16:39:16 -0700 Received: from kithrup.com (kithrup.com [140.174.23.40]) by freefall.cdrom.com (8.6.11/8.6.6) with ESMTP id QAA13672 for ; Thu, 27 Jul 1995 16:39:14 -0700 Received: (from sef@localhost) by kithrup.com (8.6.8/8.6.6) id QAA29699 for bugs@freebsd.org; Thu, 27 Jul 1995 16:39:10 -0700 Date: Thu, 27 Jul 1995 16:39:10 -0700 From: Sean Eric Fagan Message-Id: <199507272339.QAA29699@kithrup.com> To: bugs@freebsd.org Subject: panics with 2.0.5-RELEASE Sender: bugs-owner@freebsd.org Precedence: bulk This may be due to flaky hardware, of course. Anyway: I've been getting panics fairly often with 2.0.5-RELEASE, off of the CD-ROM. I finally managed to (correctly) type in the information correctly. Here it is, followed by the (hopefully relevent) section of 'nm -n /kernel', and the config file used to generate this kernel. Fatal trap 12: page fault while in kernel mode fault virtual address = 0xf036f7fa fault code = supervisor write, page not present instruction pointer = 0x8:0xf016504d code segment = base 0x0, limit 0xffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = Idle interrupt mask = net panic: page fault f0165000 T _bcopyx f0165010 T _bcopy f0165010 T _ovbcopy f0165010 t bcopy f0165054 T _memcpy f0165078 T _copyout f01650b6 t done_copyout f01650c8 t copyout_fault f01650e4 T _copyin # # GENERIC -- Generic machine with WD/AHx/NCR/BTx family disks # # GENERIC,v 1.45.2.3 1995/06/05 21:50:41 jkh Exp # machine "i386" cpu "I486_CPU" ident GARTH timezone 8 dst maxusers 10 options INET #InterNETworking options FFS #Berkeley Fast Filesystem options MFS #Memory Filesystem #options NFS #Network Filesystem #options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 options "SCSI_DELAY=15" #Be pessimistic about Joe SCSI device #options BOUNCE_BUFFERS #include support for DMA bounce buffers #options UCONSOLE #Allow users to grab the console config kernel root on sd0 swap on sd0 controller isa0 #controller pci0 controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 vector fdintr disk fd0 at fdc0 drive 0 disk fd1 at fdc0 drive 1 #tape ft0 at fdc0 drive 2 #controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr #disk wd0 at wdc0 drive 0 #disk wd1 at wdc0 drive 1 #controller wdc1 at isa? port "IO_WD2" bio irq 15 vector wdintr #disk wd2 at wdc1 drive 0 #disk wd3 at wdc1 drive 1 #controller ncr0 #controller ahc0 #controller bt0 at isa? port "IO_BT0" bio irq ? vector btintr #controller uha0 at isa? port "IO_UHA0" bio irq ? drq 5 vector uhaintr #controller ahc1 at isa? bio irq ? vector ahcintr #controller ahb0 at isa? bio irq ? vector ahbintr controller aha0 at isa? port "IO_AHA0" bio irq ? drq 5 vector ahaintr #controller aic0 at isa? port 0x340 bio irq 11 vector aicintr #controller nca0 at isa? port 0x1f88 bio irq 10 vector ncaintr #controller nca1 at isa? port 0x350 bio irq 5 vector ncaintr #controller sea0 at isa? bio irq 5 iomem 0xc8000 iosiz 0x2000 vector seaintr controller scbus0 device sd0 #device st0 device cd0 #Only need one of these, the code dynamically grows #device wt0 at isa? port 0x300 bio irq 5 drq 1 vector wtintr #device mcd0 at isa? port 0x300 bio irq 10 vector mcdintr #device mcd1 at isa? port 0x340 bio irq 11 vector mcdintr #controller matcd0 at isa? port ? bio device scd0 at isa? port 0x230 bio # syscons is the default console driver, resembling an SCO console device sc0 at isa? port "IO_KBD" tty irq 1 vector scintr # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? port "IO_KBD" tty irq 1 vector pcrint #options "PCVT_FREEBSD=210" # pcvt running on FreeBSD 2.1 #options XSERVER # include code for XFree86 device npx0 at isa? port "IO_NPX" irq 13 vector npxintr device sio0 at isa? port "IO_COM1" tty irq 4 vector siointr device sio1 at isa? port "IO_COM2" tty irq 3 vector siointr #device sio2 at isa? port "IO_COM3" tty irq 5 vector siointr #device sio3 at isa? port "IO_COM4" tty irq 9 vector siointr device lpt0 at isa? port? tty irq 7 vector lptintr #device lpt1 at isa? port? tty #device lpt2 at isa? port? tty # Order is important here due to intrusive probes, do *not* alphabetize # this list of network interfaces until the probes have been fixed. # Right now it appears that the ie0 must be probed before ep0. See # revision 1.20 of this file. #device de0 device ed0 at isa? port 0x280 net irq 5 iomem 0xd8000 vector edintr #device ed1 at isa? port 0x300 net irq 5 iomem 0xd8000 vector edintr #device ie0 at isa? port 0x360 net irq 7 iomem 0xd0000 vector ieintr #device ep0 at isa? port 0x300 net irq 10 vector epintr #device ix0 at isa? port 0x300 net irq 10 iomem 0xd0000 iosiz 32768 vector ixintr #device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 vector le_intr #device lnc0 at isa? port 0x280 net irq 10 drq 0 vector lncintr #device lnc1 at isa? port 0x300 net irq 10 drq 0 vector lncintr #device ze0 at isa? port 0x300 net irq 5 iomem 0xd8000 vector zeintr #device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 vector zpintr pseudo-device loop pseudo-device ether pseudo-device log #pseudo-device sl 1 # ijppp uses tun instead of ppp device #pseudo-device ppp 1 #pseudo-device tun 1 pseudo-device pty 16 pseudo-device gzip # Exec gzipped a.out's