From owner-freebsd-mobile Thu Jun 29 8: 1:37 2000 Delivered-To: freebsd-mobile@freebsd.org Received: from alpha.dante.org.uk (alpha.dante.org.uk [193.63.211.19]) by hub.freebsd.org (Postfix) with ESMTP id C40B137B6B9 for ; Thu, 29 Jun 2000 08:01:23 -0700 (PDT) (envelope-from Konstantin.Chuguev@dante.org.uk) Received: from theta.dante.org.uk ([193.63.211.7]) by alpha.dante.org.uk with esmtp (Exim 3.12 #4) id 137foe-0000gY-00; Thu, 29 Jun 2000 16:01:20 +0100 Received: from localhost ([127.0.0.1] helo=dante.org.uk) by theta.dante.org.uk with esmtp (Exim 3.12 #4) id 137foc-000196-00; Thu, 29 Jun 2000 16:01:18 +0100 Message-ID: <395B64BE.3D27ED@dante.org.uk> Date: Thu, 29 Jun 2000 16:01:18 +0100 From: Konstantin Chuguev Organization: Delivery of Advanced Networking Service to Europe Ltd. X-Mailer: Mozilla 4.73 [en] (X11; I; SunOS 5.6 sun4u) X-Accept-Language: en, ru MIME-Version: 1.0 To: rdmurphy@vt.edu Cc: FreeBSD-Mobile@FreeBSD.org Subject: Re: Netgear FA410TX - ed0: device timeout? References: <14683.24704.785023.470503@knock.econ.vt.edu> Content-Type: text/plain; charset=koi8-r Content-Transfer-Encoding: 7bit Sender: owner-freebsd-mobile@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.org "Russell D. Murphy Jr." wrote: > I had ordered a FA410TX card after reading some past recommendations > for it (and before reading the recent "you're out of luck" message). > It seems *close* to working, but. . . I keep getting "device timeout" > errors. It works fine under W95. I've set up pccard and ed in the > kernel as: > > The Link light on the dongle is on; I've set the iomem and irq > settings in pccard.conf to match the ones used by W95. The > pccard.conf settings and the output of pccardc dumpcis are below. > > It seems close; any suggestions? > > The pccard.conf settings (/etc/pccard.conf) are: > > io 0x120-0x13f > card "NETGEAR" "FA410TX" > config 0x20 "ed0" 11 I would suggest not to use irq11. irq9 is working fine for me. You should also try setting IO ports window accordingly to the information from configuration entry tuples from dumpcis: > > The output of pccardc dumpcis is: > > Tuple #7, code = 0x1b (Configuration entry), length = 7 > 000: e0 81 18 45 30 fc be > Config index = 0x20(default) > Interface byte = 0x81 (I/O) wait signal supported > Card decodes 5 address lines, limited 8/16 Bit I/O > IRQ modes: Level > IRQs: 2 3 4 5 6 7 9 10 11 12 13 15 > Tuple #8, code = 0x1b (Configuration entry), length = 7 > 000: 01 08 ca 60 00 03 1f > Config index = 0x1 > Card decodes 10 address lines, limited 8/16 Bit I/O > I/O address # 1: block start = 0x300 block length = 0x20 > Tuple #9, code = 0x1b (Configuration entry), length = 7 > 000: 02 08 ca 60 20 03 1f > Config index = 0x2 > Card decodes 10 address lines, limited 8/16 Bit I/O > I/O address # 1: block start = 0x320 block length = 0x20 > Tuple #10, code = 0x1b (Configuration entry), length = 7 > 000: 03 08 ca 60 40 03 1f > Config index = 0x3 > Card decodes 10 address lines, limited 8/16 Bit I/O > I/O address # 1: block start = 0x340 block length = 0x20 > Tuple #11, code = 0x1b (Configuration entry), length = 7 > 000: 04 08 ca 60 80 03 1f > Config index = 0x4 > Card decodes 10 address lines, limited 8/16 Bit I/O > I/O address # 1: block start = 0x380 block length = 0x20 io 0x300-0x37f config 0x[1-3] "ed0" 9 or io 0x380-0x39f config 0x4 "ed0" 9 -- * * Konstantin Chuguev - Application Engineer * * Francis House, 112 Hills Road * Cambridge CB2 1PQ, United Kingdom D A N T E WWW: http://www.dante.net To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-mobile" in the body of the message