Date: Tue, 8 Jul 1997 22:24:04 +0300 From: Antti-Pekka Liedes <apl@hutcs.cs.hut.fi> To: Steve Passe <smp@csn.net> Cc: freebsd-smp@FreeBSD.ORG Subject: Re: FreeBSD SMP on Soyo 5TH5? Message-ID: <19970708222404.45819@hutcs.cs.hut.fi> In-Reply-To: <199707081839.MAA24927@Ilsa.StevesCafe.com>; from Steve Passe on Tue, Jul 08, 1997 at 12:39:41PM -0600 References: <19970708210545.00117@hutcs.cs.hut.fi> <199707081839.MAA24927@Ilsa.StevesCafe.com>
next in thread | previous in thread | raw e-mail | index | archive | help
On Tue, Jul 08, 1997 at 12:39:41PM -0600, Steve Passe wrote:
> Hi,
>
> > Has anyone got FreeBSD SMP to work on a Soyo 5TH5 board? I have one of
> > these boards, equipped with two brand new pentiums (166 and 200MHz,
> > currently running at only 100MHz), NCR SCSI-controller, SMC EtherPower
>
> why only 100? does the board show instability @ 166?
>
No, I just had a 100MHz Pentium as one CPU earlier, and I just haven't
configured the board for 166MHz yet.
> ---
> > 10/100, Matrox Millenium, and SB32 soundcard. I have tried several
> > combinations of kernel options, each failing with quite a random looking
> > results (the "best" result was to get both CPUs into the scheduler, but
> > immediatly when the system began to run rc, I get a screen full of "I'm in
> > cpu #1 and should be in #0" messages and panic). I'm not in FreeBSD right
> > now, so I don't have dmesg or mptable output handy, but I can get those if
> > needed to solve the problem.
>
> We definately need both: do "mptable -dmesg > outfile" from a UP kernel.
> Do any messages PRECEED the "I'm in cpu #1 and should be in #0" messages?
>
I can't tell if anything preceeded the messages because they filled my
screen way too fast. In the end there was a "timeout waiting for cpu #0"
message, then failed disk sync and finally panic.
Oh, I tried to change all IRQs to legacy ISA in BIOS, this produced
different results:
The kernel itself finished booting, in the end it said that both
processors are in the scheduler. It did fscks from rc-files, but ifconfig
caused a "page fault in kernel mode".
Ok, I was using NT when I wrote my first mail, so I didn't have these, but
here they are, I've tried exactly these kernel options as well as some
other combinations, without much success.
===============================================================================
MPTable, version 2.0.12
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000f0d20
signature: '_MP_'
length: 16 bytes
version: 1.1
checksum: 0x53
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000f0d34
signature: 'PCMP'
base table length: 292
version: 1.1
checksum: 0xd5
OEM ID: 'OEM00000'
Product ID: 'PROD00000000'
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 28
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x11 BSP, usable 5 2 1 0x07bf
1 0x11 AP, usable 5 2 1 0x07bf
--
Bus: Bus ID Type
0 ISA
1 PCI
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID INT#
ExtINT conforms conforms 0 0 2 0
INT conforms conforms 0 1 2 1
INT conforms conforms 0 0 2 2
INT conforms conforms 0 3 2 3
INT conforms conforms 0 4 2 4
INT conforms conforms 0 5 2 5
INT conforms conforms 0 6 2 6
INT conforms conforms 0 7 2 7
INT conforms conforms 0 8 2 8
INT conforms conforms 0 9 2 9
INT conforms conforms 0 10 2 10
INT conforms conforms 0 11 2 11
INT conforms conforms 0 12 2 12
INT conforms conforms 0 13 2 13
INT conforms conforms 0 14 2 14
INT conforms conforms 0 15 2 15
INT active-lo level 1 14:A 2 16
INT active-lo level 1 15:A 2 17
INT active-lo level 1 16:A 2 18
INT active-lo level 1 17:A 2 19
SMI conforms conforms 0 0 2 23
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID INT#
ExtINT active-hi edge 0 0 255 0
NMI active-hi edge 0 0 255 1
-------------------------------------------------------------------------------
# SMP kernel config file options:
# Required:
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
# Useful:
#options SMP_AUTOSTART # start the additional CPUs during boot
# Optional (built-in defaults will work in most cases):
#options NCPU=2 # number of CPUs
#options NBUS=2 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
# Rogue hardware:
#
# Tyan Tomcat II:
#options SMP_TIMER_NC #
#
# SuperMicro P6DNE:
#options SMP_TIMER_NC #
-------------------------------------------------------------------------------
dmesg output:
Copyright (c) 1992-1997 FreeBSD Inc.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 3.0-CURRENT #0: Tue Jul 8 16:28:11 EET DST 1997
apl@apocalypse.tky.hut.fi:/var/src/sys/compile/APOCALYPSE
CPU: Pentium (99.65-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x52c Stepping=12
Features=0x3bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC>
real memory = 67108864 (65536K bytes)
Physical memory hole(s):
avail memory = 63037440 (61560K bytes)
DEVFS: ready for devices
Probing for devices on PCI bus 0:
chip0: <Intel 82439> rev 0x03 on pci0.0.0
chip1: <Intel 82371SB PCI to ISA bridge> rev 0x01 on pci0.7.0
chip2: <Intel 82371SB IDE interface> rev 0x00 on pci0.7.1
vga0: <VGA-compatible display device> rev 0x01 int a irq 9 on pci0.14.0
ncr0: <ncr 53c810 scsi> rev 0x01 int a irq 9 on pci0.15.0
ncr0: waiting for scsi devices to settle
scbus0 at ncr0 bus 0
scbus0 target 0 lun 0: 5.0 MB/s (200 ns, offset 8)
sd0 at scbus0 target 0 lun 0
sd0: <IBM DSAS-3540 S47W> type 0 fixed SCSI 2
sd0: Direct-Access
sd0: 10.0 MB/s (100 ns, offset 8)
522MB (1070496 512 byte sectors)
sd1 at scbus0 target 5 lun 0
sd1: <QUANTUM FIREBALL_TM3200S 300X> type 0 fixed SCSI 2
sd1: Direct-Access
sd1: 10.0 MB/s (100 ns, offset 8)
3067MB (6281856 512 byte sectors)
sd2 at scbus0 target 6 lun 0
sd2: <QUANTUM FIREBALL_TM3200S 300X> type 0 fixed SCSI 2
sd2: Direct-Access
sd2: 10.0 MB/s (100 ns, offset 8)
3067MB (6281856 512 byte sectors)
de0: <Digital 21140A Fast Ethernet> rev 0x20 int a irq 11 on pci0.17.0
de0: SMC 9334BDT 21140A [10-100Mb/s] pass 2.0
de0: address 00:00:c0:30:46:f9
Probing for devices on the ISA bus:
sc0 at 0x60-0x6f irq 1 on motherboard
sc0: VGA color <16 virtual consoles, flags=0x0>
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
lpt0 at 0x378-0x37f irq 7 on isa
lpt0: Interrupt-driven port
lp0: TCP/IP capable interface
psm0 at 0x60-0x64 irq 12 on motherboard
psm0: device ID 0
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: NEC 72065B
fd0: 1.44MB 3.5in
wdc0 at 0x1f0-0x1f7 irq 14 on isa
wdc0: unit 1 (atapi): <CD820E.1v78b9108/1.03>, removable, dma, iordy
wcd0: 859/1375Kb/sec, 240Kb cache, audio play, 255 volume levels, ejectable tray
wcd0: 120mm data disc loaded, unlocked
sb0 at 0x220-0x22f irq 5 drq 1 on isa
sb0: <SoundBlaster 16 4.13>
sbxvi0 at 0x220-0x22f irq 5 drq 5 on isa
sbxvi0: <SoundBlaster 16 4.13>
sbmidi0 at 0x330-0x331 irq 5 on isa
sbmidi0: <SoundBlaster 16 MPU-401>
npx0 on motherboard
npx0: INT 16 interface
DEVFS: ready to run
ccd0-3: Concatenated disk drivers
WARNING: / was not properly dismounted.
de0: enabling 10baseT port
===============================================================================
> --
> Steve Passe | powered by
> smp@csn.net | Symmetric MultiProcessor FreeBSD
>
--
Antti-Pekka Liedes * apl@IRC apl@iki.fi * In two hells there's
JMT 6 B 406 * apl@cs.hut.fi * one hell too many
02150 ESPOO * apl@apocalypse.tky.hut.fi * - Lucifer
+358 - 9 - 468 3121 * +358 - 40 - 5873 593 * (in God's Army)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?19970708222404.45819>