Date: Tue, 12 Mar 2002 23:27:31 +0200 From: Richard =?utf-8?B?xIxlcGFz?= <rch@richard.eu.org> To: freebsd-questions@FreeBSD.ORG Subject: Re: Setting up Vhosting on Dynamic IP Message-ID: <20020312212731.GC60275@richard.eu.org> In-Reply-To: <3.0.5.32.20020312151945.01155d18@mail.sage-one.net> References: <3.0.5.32.20020312145637.01155d18@mail.sage-one.net> <3.0.5.32.20020312145637.01155d18@mail.sage-one.net> <3.0.5.32.20020312151945.01155d18@mail.sage-one.net>
next in thread | previous in thread | raw e-mail | index | archive | help
'ppp' & ipfw cares about that automatically. Apache config deals with ip addresses only. In my particular config 127.0.0.3 is alias for lo0 (see /etc/defaults/rc.conf). On Tue Mar 12 15:19:45 2002 -0600 Server Admin wrote: >Thanks, but what about the interface aliases setup? ...especially if "tun0" >is used.??? > >At 11:04 PM 3.12.2002 +0200, Richard =?utf-8?B?xIxlcGFz?= wrote: >>I don't know if it works for vhost, but I use the following for apache: >>NameVirtualHost 127.0.0.3:80 >>NameVirtualHost *:80 >>Listen 127.0.0.3:80 >># _default_ catches all dynamic external addresses >><VirtualHost 127.0.0.3:80 _default_:80 > >></VirtualHost> >><VirtualHost 127.0.0.3:80 *:80 > >></VirtualHost> >> >>and this for ipfw: >>00120 fwd 127.0.0.3 tcp from any to me 80 via tun0 >> >>On Tue Mar 12 14:56:37 2002 -0600 Server Admin wrote: >> >>>Running FreeBSD 4.5-STABLE >>> >>>On a new server using DSL PPPoE, is it possible to set it up as a >>>named-based host for vhosting. While I've read up on this and have a fairly >>>good grasp, I'm still not (precisely) clear where the vhosts' aliases would >>>go since I use a tunnel interface "tun0" for the external and have a >>>dynamic IP (use Dynamic DNS host). I have the following components: >>> >>>1) Web Server is the gateway and a caching name server (named & BIND ) with >>>two NICs >>>2) Use Dynamic DNS service >>>3) Running IPFW and NATD with packet divert to tun0 >>>4) Running Apache & Frontpage >>>5) Interfaces: >>> a) rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 >>> inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 >>> b) rl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 >>> c) tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1492 >>> inet xx.xxx.xx.xxx --> xx.xxx.xx.xxx netmask 0xffffffff >>> >>>6) Also should mention the above server is used for mail too. Sendmail & >>>qpopper which I will have to configure for vhosts too. >>> >>>THE MAIN QUESTION (so far): >>>If it is possible to set up virtual hosting without a static IP as above >>>and if so, should the aliases for each vhost go with the rl0 interface..??? >>> >>>Later on, I plan to move to a static IP with 6MBS DSL speeds, but more >>>expensive. However, for now, I can make do with the slower DSL for the >>>less-active hosts being moved over to this server at the beginning. >>>Unfortunately, it comes with dynamic IP. >>> >>>Sorry the above is so long, but brief as possible. Appreciate any help on >>>this.... thanks! >>>.... our website: http://www.sage-one.net/ >>> >>>Best regards, >>> >>>Jack L. Stone >>>Server Admin >>> >>>To Unsubscribe: send mail to majordomo@FreeBSD.org >>>with "unsubscribe freebsd-questions" in the body of the message >> >>-- >> â» RiÄardas Äepas ⺠>> >>To Unsubscribe: send mail to majordomo@FreeBSD.org >>with "unsubscribe freebsd-questions" in the body of the message >> >> >.... our website: http://www.sage-one.net/ > >Best regards, > >Jack L. Stone >Server Admin -- ☻ Ričardas Čepas ☺ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020312212731.GC60275>