Date: Thu, 10 Dec 2009 17:22:56 +0300 From: Irek Bagautdinov <irek.bagautdinov@gmail.com> To: freebsd-scsi@freebsd.org Subject: QLogic 2422 Fiber channel problems. Message-ID: <b16544a0912100622m780459dw9742072df6f57507@mail.gmail.com>
next in thread | raw e-mail | index | archive | help
Hi. We have IBM Blade chassis with HS21 Servers. Fiber Channel card is QLogic 2422 Also we have DS 3400 storage. # uname -a FreeBSD 7.2-RELEASE FreeBSD 7.2-RELEASE #0: Fri May 1 07:18:07 UTC 2009 root@driscoll.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC amd64 # cat /boot/loader.conf ispfw_load="YES" isp_load="YES" is this errors critical? We can write/read on this device. but On boot and fsck: isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 isp0: 0.0.3 FCP RESPONSE: 0x2 (probe1097:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 (probe1097:umass-sim0:0:0:0): CAM Status: SCSI Status Error (probe1097:umass-sim0:0:0:0): SCSI Status: Check Condition (probe1097:umass-sim0:0:0:0): UNIT ATTENTION asc:29,0 (probe1097:umass-sim0:0:0:0): Power on, reset, or bus device reset occurred (probe1097:umass-sim0:0:0:0): Retrying Command (per Sense Data) (probe1097:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 (probe1097:umass-sim0:0:0:0): CAM Status: SCSI Status Error (probe1097:umass-sim0:0:0:0): SCSI Status: Check Condition (probe1097:umass-sim0:0:0:0): NOT READY asc:3a,0 (probe1097:umass-sim0:0:0:0): Medium not present (probe1097:umass-sim0:0:0:0): Unretryable error da0 at isp0 bus 0 target 0 lun 3SMP: AP CPU #3 Launched! SMP: AP CPU #1 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #6 Launched! SMP: AP CPU #5 Launched! SMP: AP CPU #7 Launched! SMP: AP CPU #4 Launched! da0: <IBM 1726-4xx FAStT 0617> Fixed Direct Access SCSI-5 device da0: 400.000MB/s transfers da0: Command Queueing Enabled da0: 571180MB (1169776640 512 byte sectors: 255H 63S/T 72815C) (da0:isp0:0:0:3): Synchronize cache failed, status == 0x59, scsi status == 0x0 GEOM_LABEL: Label for provider da0 is ufsid/4b1f17e8674fa3c8. isp0: 0.0.3 FCP RESPONSE: 0x2 (da0:isp0:0:0:3): Synchronize cache failed, status == 0x59, scsi status == 0x0 isp0: 0.0.3 FCP RESPONSE: 0x2 (da0:isp0:0:0:3): Synchronize cache failed, status == 0x59, scsi status == 0x0 isp0: 0.0.3 FCP RESPONSE: 0x2 (da0:isp0:0:0:3): Synchronize cache failed, status == 0x59, scsi status == 0x0 isp0: 0.0.3 FCP RESPONSE: 0x2 (da0:isp0:0:0:3): Synchronize cache failed, status == 0x59, scsi status == 0x0 isp0: 0.0.3 FCP RESPONSE: 0x2 (da0:isp0:0:0:3): Synchronize cache failed, status == 0x59, scsi status == 0x0 isp0: 0.0.3 FCP RESPONSE: 0x2 (da0:isp0:0:0:3): Synchronize cache failed, status == 0x59, scsi status == 0x0 Also we have storage switch-MDS 9000 as ibm blade module. If we enable few fiber channel switch ports per zone/zoneset and VSAN FreeBSD see few daX disks. Possible we must setup multipath via geom?
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?b16544a0912100622m780459dw9742072df6f57507>