Date: Wed, 4 Jul 2001 14:47:27 +0200 From: "Eckhard Kantz" <Eckhard.Kantz@gmx.de> To: <freebsd-mobile@freebsd.org>, <freebsd-questions@freebsd.org> Subject: Realtek 8139 Message-ID: <00af01c10487$7bab3b40$be00a8c0@wegalink.net>
next in thread | raw e-mail | index | archive | help
Could anyone provide some hints how to get a LevelOne PCMCIA card with the Realtek 8139 chipset up
and running under FreeBSD 4.1?
I tried one card 10 MBit and a second one 10/100 MBit but neither worked. Accordingly to well known
hints I booted Windows and wrote down all parameters for memory, i/o and irq used there. Next I
tried with pccardc to apply the same hardware parameters but it didn't work.
Please find dmesg below. In case of general problems with those network cards, what other type of
10/100 MBit card could be recommended?
Thanks for any advice.
Eckhard
mailto:Eckhard.Kantz@gmx.de
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #0: Fri Jul 28 13:01:29 GMT 2000
inof@bestwishes.fromme.com:/usr/src/sys/compile/GENERIC
Timecounter "i8254" frequency 1193182 Hz
CPU: AMD-K6(tm) 3D processor (366.60-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x58c Stepping = 12
Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX>
AMD Features=0x80000800<SYSCALL,3DNow!>
real memory = 134217728 (131072K bytes)
config> di sn0
config> di lnc0
config> di le0
config> di ie0
config> di fe0
config> di cs0
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> en pcic0
config> po pcic0 0x3e0
config> ir pcic0 10
config> iom pcic0 0xc0000
config> f pcic0 0
config> q
avail memory = 126398464 (123436K bytes)
Preloaded elf kernel "kernel" at 0xc040d000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc040d09c.
K6-family MTRR support enabled (2 registers)
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1100-0x110f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xf300-0xf31f irq 10 at device 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port 1 power on failed, IOERROR
uhub0: port 2 power on failed, IOERROR
ums0: Logitech Inc. iFeel Mouse , rev 1.00/1.01, addr 2, iclass 3/1
ums0: 3 buttons and Z dir.
chip1: <Intel 82371AB Power management controller> port 0x1400-0x140f at device 7.3 on pci0
pci0: <S3 ViRGE MX graphics accelerator> at 8.0
pcic-pci0: <TI PCI-1225 PCI-CardBus Bridge> at device 10.0 on pci0
pcic-pci0: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
pcic-pci1: <TI PCI-1225 PCI-CardBus Bridge> at device 10.1 on pci0
pcic-pci1: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model GlidePoint, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
pcic0: <VLSI 82C146> at port 0x3e0 iomem 0xc0000 irq 10 drq 0 on isa0
pcic0: management irq 11
pccard0: <PC Card bus -- kludge version> on pcic0
pccard1: <PC Card bus -- kludge version> on pcic0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
pccard: card inserted, slot 0
pccard: card inserted, slot 1
ata1-slave: ata_command: timeout waiting for intr
ata1-slave: identify failed
ad0: 19077MB <IBM-DJSA-220> [38760/16/63] at ata0-master using UDMA33
acd0: CDROM <CD-224E> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s3a
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?00af01c10487$7bab3b40$be00a8c0>