From owner-freebsd-questions Sun Jul 2 16:46:14 1995 Return-Path: questions-owner Received: (from majordom@localhost) by freefall.cdrom.com (8.6.10/8.6.6) id QAA13038 for questions-outgoing; Sun, 2 Jul 1995 16:46:14 -0700 Received: from localhost.cdrom.com (localhost.cdrom.com [127.0.0.1]) by freefall.cdrom.com (8.6.10/8.6.6) with SMTP id QAA13032 for ; Sun, 2 Jul 1995 16:46:13 -0700 X-Authentication-Warning: freefall.cdrom.com: Host localhost.cdrom.com didn't use HELO protocol Prev-Resent: Sun, 02 Jul 1995 16:46:12 -0700 Prev-Resent: "questions@freebsd.org " Received: from netcomsv.netcom.com (uucp9.netcom.com [163.179.3.9]) by freefall.cdrom.com (8.6.10/8.6.6) with ESMTP id MAA07223 for ; Sun, 2 Jul 1995 12:10:42 -0700 Received: from pop.com by netcomsv.netcom.com with UUCP (8.6.12/SMI-4.1) id MAA17120; Sun, 2 Jul 1995 12:00:26 -0700 From: djnowak@pop.com (David Nowak) Reply-To: djnowak@pop.com To: jkh@freebsd.org Subject: Problems with Seagate Drive Date: 02 Jul 1995 18:26:54 GMT Message-Id: <1880948734.12176714@pop.com> Organization: DigitalPopcorn Online Services Resent-To: questions@freebsd.org Resent-Date: Sun, 02 Jul 1995 16:46:12 -0700 Resent-Message-ID: <13031.804728772@freefall.cdrom.com> Resent-From: "Jordan K. Hubbard" Sender: questions-owner@freebsd.org Precedence: bulk I would like to run FreeBSD on my 386 system and have been informed that you have written a Seagate SCSI driver for FreeBSD that may be compatible with it. I have ftped version 2.0.5 of the root.flp and bindist of FreeBSD 2.0.5 RELEASE. Apparently Drew Eckhardt (drew@colorado.edu) has written a Seagate ST01/Future Domain TMC-885 compatible Linux driver which I have been using with Linux for several months now. Do you use the same driver for FreeBSD 2.0.5? If so, why can't I use it from the boot.flp disk? I have a Future Domain TMC-885M SCSI controller card (IRQ 5, memory address jumper at 0xC8000 and ROM BIOS 950 AT v8.00) and a Quantum P80 hard drive. When I start up from the boot disk to install FreeBSD 2.0.5, the PARTITION submenu item of the INSTALL menu does not recognize my FD card. When I rebooted my system and type "-c" to enter the userconfig mode, and type in "probe SEA0" I get the following error messages: Fatal trap 12: page fault while in kernal mode fault virtual address = 0x0 fault code = supervisor read, page not present instruction pointer = 0x8:0f01130f6 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def 32 1, gran 1 processor eflags = resume, IOPL = 0 current process = 0 () interrupt mask = net tty bio panic: page fault hit reset please Jordan, Do you have any workarounds for me to get past this roadblock? Any suggestions would be appreciated. Thanks. David Nowak djnowak@pop.com --