Date: 05 Mar 2004 13:10:18 +0000 From: alan barrow <alan.barrow@psineteurope.com> To: "freebsd-amd64@freebsd.org" <freebsd-amd64@freebsd.org> Cc: techsupport@tyan.com Subject: Tyan S2882UG3NR Message-ID: <1078492218.9948.42.camel@ip5.ops.uk.psi.com>
next in thread | raw e-mail | index | archive | help
Quick run down of this mornings efforts to get FreeBSD 5.2 on the Thunder K8S Pro. Moan groan... just one problem.... The on board adaptec SCSI.. The attempted install of FreeBSD 5.2.. This model:- http://www.tyan.com/products/html/tx28b2880.html Thunder K8S Pro -- S2882UG3NR [ BIOS Ver. 101 ] 2 x 246 2GB DDR ECC 4 x 36GB 10Krpm SCSI HDDs CD-ROM -- TEAC -- (moved from primary master to secondary slave) floppy #################################################################### BIOS -- set to optimal or default. 1) No access to adaptec <ctrl +A> card BIOS or LSI BIOS <ctrl+m> using these key strokes throws the machine straight into boot. 2) Using the PCI-X Riser card slot 1 with megaraid 320-1 causes IRQ steering errors to be reported by the BIOS on boot. 3) Using the PCI-X Riser card slot 2 with megaraid 320-1 removes the errors but the issue is the same as 1). #################################################################### Tests :-- 1) BIOS -- set to default .. the following turned off. * IDE off * floppy off * ACPI off * Device and PCI Slots (All DMA off) * USB Host controllers Diasabled * Onboard SATA disabled (why have this at all???) * Onboard AIC-7902W SCSI Disabled * Onboard ZCR N/A * Onboard GB lan Disabled * Onboard GB lan Rom Disabled * Serial Port 1 / 2 / parallel off * Onboard floppy controller disabled * Remote Access Disabled * Plug & Play OS No Result :- No access to the MegaRAID BIOS. (Notice the SCSI has been disabled here) ####################################################### 2) BIOS -- set to default .. the following turned off. * IDE off * floppy off * ACPI off * Device and PCI Slots (All DMA off) * USB Host controllers Diasabled * Onboard SATA disabled * Onboard GB lan Disabled * Onboard GB lan Rom Disabled * Serial Port 1 / 2 / parallel off * Onboard floppy controller disabled * Remote Access Disab Result :- No access to the MegaRAID or adaptec BIOSs. (Notice the SCSI has been disabled here) ####################################################### 3) BIOS -- set to default .. the following turned off. * IDE off * floppy off * ACPI off * Device and PCI Slots (All DMA off) * USB Host controllers Diasabled * Onboard SATA disabled * Onboard GB lan Disabled * Onboard GB lan Rom Disabled * Serial Port 1 / 2 / parallel off * Onboard floppy controller disabled * Remote Access Disab Remove the Megaraid card from the system entirely. Internal SCSI becomes a boot from device option. ###################################################### Right so with the megaraid out option 3) BIOS set and the SCSI devices hanging off the internal SCSI, The following is the DMESG. Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-RELEASE #0: Sun Jan 11 04:21:45 GMT 2004 root@wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc09e1000. MPTable: <TEMPLATE ETEMPLATE > Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: AMD Opteron(tm) Processor 246 (1991.43-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0xf58 Stepping = 8 Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> AMD Features=0xe0500000<NX,AMIE,LM,DSP,3DNow!> real memory = 2147483648 (2048 MB) avail memory = 2080739328 (1984 MB) FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0: Assuming intbase of 0 ioapic1: Assuming intbase of 24 ioapic2: Assuming intbase of 28 ioapic0 <Version 1.1> irqs 0-23 on motherboard ioapic1 <Version 1.1> irqs 24-27 on motherboard ioapic2 <Version 1.1> irqs 28-31 on motherboard Pentium Pro MTRR support enabled npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface pcibios: BIOS version 2.10 Using $PIR table, 15 entries at 0xc00f2720 pcib0: <MPTable Host-PCI bridge> at pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pcib0: slot 7 INTD routed to irq 19 pcib1: <MPTable PCI-PCI bridge> at device 6.0 on pci0 pci3: <PCI bus> on pcib1 pcib1: slot 0 INTD routed to irq 19 pcib1: slot 0 INTD routed to irq 19 pcib1: slot 8 INTA routed to irq 18 ohci0: <OHCI (generic) USB controller> mem 0xfeafd000-0xfeafdfff irq 19 at device 0.0 on pci3 usb0: OHCI version 1.0, legacy support usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 3 ports with 3 removable, self powered ohci1: <OHCI (generic) USB controller> mem 0xfeafe000-0xfeafefff irq 19 at device 0.1 on pci3 usb1: OHCI version 1.0, legacy support usb1: <OHCI (generic) USB controller> on ohci1 usb1: USB revision 1.0 uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 3 ports with 3 removable, self powered pci3: <display, VGA> at device 6.0 (no driver attached) fxp0: <Intel 82551 Pro/100 Ethernet> port 0xbc00-0xbc3f mem 0xfeaa0000-0xfeabffff,0xfeafc000-0xfeafcfff irq 18 at device 8.0 on pci3 fxp0: Ethernet address 00:e0:81:28:fb:04 miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <AMD 8111 UDMA133 controller> port 0xffa0-0xffaf at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: <serial bus, SMBus> at device 7.2 (no driver attached) pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) pcib2: <MPTable PCI-PCI bridge> at device 10.0 on pci0 pci2: <PCI bus> on pcib2 pcib2: slot 6 INTA routed to irq 24 pcib2: slot 6 INTB routed to irq 25 pcib2: slot 9 INTA routed to irq 24 pcib2: slot 9 INTB routed to irq 25 ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x9800-0x98ff,0xa000-0xa0ff mem 0xfc9fc000-0xfc9fdfff irq 24 at device 6.0 on pci2 aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0xa400-0xa4ff,0xa800-0xa8ff mem 0xfc9fe000-0xfc9fffff irq 25 at device 6.1 on pci2 aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem 0xfc9a0000-0xfc9affff,0xfc9b0000-0xfc9bffff irq 24 at device 9.0 on pci2 bge0: Ethernet address: 00:e0:81:28:fb:1a miibus1: <MII bus> on bge0 brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus1 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem 0xfc9d0000-0xfc9dffff,0xfc9e0000-0xfc9effff irq 25 at device 9.1 on pci2 bge1: Ethernet address: 00:e0:81:28:fb:1b miibus2: <MII bus> on bge1 brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus2 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto pci0: <base peripheral, interrupt controller> at device 10.1 (no driver attached) pcib3: <PCIBIOS PCI-PCI bridge> at device 11.0 on pci0 pci1: <PCI bus> on pcib3 pci0: <base peripheral, interrupt controller> at device 11.1 (no driver attached) orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0 pmtimer0 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 fdc0: ready for input in output fdc0: cmd 3 failed at out byte 1 of 3 ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 unknown: <PNP0303> can't assign resources (port) unknown: <PNP0501> can't assign resources (port) Timecounters tick every 10.000 msec Waiting 15 seconds for SCSI devices to settle ahd0: Invalid Sequencer interrupt occurred. >>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<< ahd0: Dumping Card State at program address 0x216 Mode 0x0 Card was paused HS_MAILBOX[0x0] INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] SAVED_MODE[0x11] DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE) SCSISIGI[0x0]:(P_DATAOUT) SCSIPHASE[0x0] SCSIBUS[0x0] LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE) SCSISEQ0[0x0] SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI) SEQCTL0[0x0] SEQINTCTL[0x6]:(INTMASK1|INTMASK2) SEQ_FLAGS[0x0] SEQ_FLAGS2[0x0] SSTAT0[0x0] SSTAT1[0x0] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0] SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0] LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x0] SCB Count = 16 CMDS_PENDING = 1 LASTSCB 0xffff CURRSCB 0xf NEXTSCB 0xff40 qinstart = 41 qinfifonext = 44 QINFIFO: 0xe 0xf 0xc WAITING_TID_QUEUES: 2 ( 0xd ) Pending list: 12 FIFO_USE[0x0] SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x37] 15 FIFO_USE[0x0] SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x7] 14 FIFO_USE[0x0] SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x17] 13 FIFO_USE[0x0] SCB_CONTROL[0x40]:(DISCENB) SCB_SCSIID[0x27] Total 4 Kernel Free SCB list: 1 2 3 4 5 6 7 8 9 10 11 0 Sequencer Complete DMA-inprog list: Sequencer Complete list: Sequencer DMA-Up and Complete list: ahd0: FIFO0 Free, LONGJMP == 0x8000, SCB 0xc SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS) SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0] SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0 HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL) ahd0: FIFO1 Free, LONGJMP == 0x8063, SCB 0xf SEQIMODE[0x3f]:(ENCFG4TCMD|ENCFG4ICMD|ENCFG4TSTAT|ENCFG4ISTAT|ENCFG4DATA|ENSAVEPTRS) SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]:(FIFOEMP|HDONE|PRELOAD_AVAIL) SG_CACHE_SHADOW[0x2]:(LAST_SEG) SG_STATE[0x0] DFFSXFRCTL[0x0] SOFFCNT[0x0] MDFFSTAT[0x5]:(FIFOFREE|DLZERO) SHADDR = 0x00, SHCNT = 0x0 HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]:(SG_CACHE_AVAIL) LQIN: 0x8 0x0 0x0 0xc 0x0 0x1 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 ahd0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x52 ahd0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1 SIMODE0[0xc]:(ENOVERRUN|ENIOERR) CCSCBCTL[0x4]:(CCSCBDIR) ahd0: REG0 == 0xb67, SINDEX = 0x10e, DINDEX = 0x108 ahd0: SCBPTR == 0xc, SCB_NEXT == 0xff40, SCB_NEXT2 == 0xf CDB 12 20 0 80 8 32 STACK: 0x211 0x2 0x0 0x0 0x0 0x0 0x0 0x0 >>>>>>>>>>>>>>>>> GEOM: create disk da0 dp=0xc8674850 GEOM: create disk da1 dp=0xc8680c50 GEOM: create disk da2 dp=0xc82ef450 GEOM: create disk da3 dp=0xc8674c50 Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0 0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0 SMP: AP CPU #1 Launched! Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0 0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0 Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0 0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0 Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0 0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0 da0 at ahd0 bus 0 target 0 lun 0 da0: <SEAGATE ST336607LC 0007> Fixed Direct Access SCSI-3 device da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da0: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C) da1 at ahd0 bus 0 target 1 lun 0 da1: <SEAGATE ST336607LC 0007> Fixed Direct Access SCSI-3 device da1: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da1: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C) da3 at ahd0 bus 0 target 3 lun 0 da3: <SEAGATE ST336607LC 0007> Fixed Direct Access SCSI-3 device da3: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da3: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C) da2 at ahd0 bus 0 target 2 lun 0 da2: <SEAGATE ST336607LC 0007> Fixed Direct Access SCSI-3 device da2: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da2: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C) Mounting root from ufs:/dev/da0s1a then straight into boot. yours me.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?1078492218.9948.42.camel>