Date: Sun, 6 Aug 2000 14:47:52 -0700 (PDT) From: fujie zhang <fujiezhang@yahoo.com> To: brianm@moffetimages.com Cc: freebsd-questions@freebsd.org Subject: USR PCI modem configuration Message-ID: <20000806214752.13308.qmail@web1401.mail.yahoo.com>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Dear Mr. Moffet,
Browsing the mail archives, i came to know that you
have successfully configured a USR PCI fax modem. i
have one just like yours, and i'm struggling to get it
to work. the "pciconf" out put is as follows:
none3@pci1:14:0: class=0x070002 card=0x00a212b9
chip=0x100812b9 rev=0x01 hdr=0x00
the "boot -v" shows the card as:
found-> vendor=0x12b9, dev=0x1008, revid=0x01
class=07-00-02, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 4, range 32, base 0000d400, size 3,
port disabled
notice that the only difference between mine and yours
is that the irq is strangely "255". and of course the
base address is different. but i guess that's OK.
Windoze assigns the card with IRQ 5 and COM5 (Yes,
COM5 though i have only two COM ports). how do you
suggest i should go about solving this problem? i'm
running current as of August 3, 2000.
i also attached the whole output of the dmesg command
after booted with "boot -v". as you will see there i
have problem with the sound and TV (bktr) cards, too.
any pointers on those? appreciate your help.
fujie
__________________________________________________
Do You Yahoo!?
Kick off your party with Yahoo! Invites.
http://invites.yahoo.com/
[-- Attachment #2 --]
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-20000803-CURRENT #0: Sat Aug 5 08:49:25 EDT 2000
root@:/usr/src/sys/compile/Cathy
Calibrating clock(s) ... TSC clock: 403594743 Hz, i8254 clock: 1193184 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 403595580 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (403.60-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x653 Stepping = 3
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 66043904 (64496K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00313000 - 0x03ef3fff, 62787584 bytes (15329 pages)
avail memory = 61300736 (59864K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f92a0
bios32: Entry = 0xf06b0 (c00f06b0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0x8b0
pnpbios: Found PnP BIOS data at 0xc00fc250
pnpbios: Entry = f0000:c280 Rev = 1.0
pnpbios: OEM ID cd041
Other BIOS signatures found:
ACPI: 000f5e90
Preloaded elf kernel "kernel" at 0xc02fa000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc02fa0a8.
nulldev: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
Creating DISK md0
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82810E (i810E GMCH) Host To Hub bridge> on motherboard
found-> vendor=0x8086, dev=0x7124, revid=0x03
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7125, revid=0x03
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 3, range 32, base e4000000, size 26, enabled
map[14]: type 1, range 32, base e3000000, size 19, enabled
found-> vendor=0x8086, dev=0x2418, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x2410, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x2411, revid=0x02
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 4, range 32, base 0000b800, size 4, enabled
found-> vendor=0x8086, dev=0x2412, revid=0x02
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=9
map[20]: type 4, range 32, base 0000b400, size 5, enabled
found-> vendor=0x8086, dev=0x2413, revid=0x02
class=0c-05-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=b, irq=10
map[20]: type 4, range 32, base 0000e800, size 4, enabled
pci0: <PCI bus> on pcib0
pci0: <Intel 82810E (i810E GMCH) Host To Hub bridge> (vendor=0x8086, dev=0x7124) at 0.0
agp0: <Intel 82810E (i810E GMCH) SVGA controller> mem 0xe3000000-0xe307ffff,0xe4000000-0xe7ffffff irq 11 at device 1.0 on pci0
agp0: allocating GATT for aperture of size 64M
pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
found-> vendor=0x109e, dev=0x0350, revid=0x12
class=04-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 3, range 32, base e3800000, size 12, memory disabled
found-> vendor=0x1274, dev=0x1371, revid=0x02
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 4, range 32, base 0000d800, size 6, port disabled
found-> vendor=0x12b9, dev=0x1008, revid=0x01
class=07-00-02, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 4, range 32, base 0000d400, size 3, port disabled
pci1: <PCI bus> on pcib1
bktr0: <BrookTree 848A> at device 8.0 on pci1
bktr0: could not map memory
device_probe_and_attach: bktr0 attach returned 6
pcm0: <AudioPCI ES1371> at device 11.0 on pci1
pcm0: unable to map register space
device_probe_and_attach: pcm0 attach returned 6
pci1: <unknown card> (vendor=0x12b9, dev=0x1008) at 14.0
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH ATA66 controller> port 0xb800-0xb80f at device 31.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0xb800
ata0: mask=03 status0=50 status1=50
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x9
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0xb808
ata1: mask=03 status0=00 status1=00
ata1: mask=03 status0=00 status1=00
ata1: devices = 0x0
ata1: probe allocation failed
pci0: <Intel 82801AA (ICH) USB controller> (vendor=0x8086, dev=0x2412) at 31.2 irq 9
pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 10
pnpbios: 17 devices, largest 126 bytes
PNP0401: adding dma mask 0x8
PNP0401: adding irq mask 0x80
PNP0401: adding io range 0x378-0x37f, size=0x8, align=0
PNP0401: adding io range 0x778-0x77f, size=0x8, align=0
PNP0401: end config
pnpbios: handle 1 device ID PNP0401 (0104d041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
PNP0501: end config
pnpbios: handle 2 device ID PNP0501 (0105d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
PNP0501: end config
pnpbios: handle 3 device ID PNP0501 (0105d041)
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f2-0x3f5, size=0x4, align=0
PNP0700: end config
pnpbios: handle 4 device ID PNP0700 (0007d041)
PNPb02f: adding io range 0x200-0x207, size=0x8, align=0
PNPb02f: end config
pnpbios: handle 5 device ID PNPb02f (2fb0d041)
PNP0f13: adding irq mask 0x1000
PNP0f13: end config
pnpbios: handle 7 device ID PNP0f13 (130fd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0x100000-0x3efffff, size=0x3e00000
PNP0c01: adding fixed memory32 range 0xe8000-0xeffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c01: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xc8000-0xcffff, size=0x8000
PNP0c01: adding fixed memory32 range 0xfff80000-0xffffffff, size=0x80000
PNP0c01: end config
pnpbios: handle 8 device ID PNP0c01 (010cd041)
INT0800: adding fixed memory32 range 0xffb80000-0xffbfffff, size=0x80000
INT0800: end config
pnpbios: handle 9 device ID INT0800 (0008d425)
PNP0000: adding irq mask 0x4
PNP0000: adding io range 0x20-0x21, size=0x2, align=0
PNP0000: adding io range 0xa0-0xa1, size=0x2, align=0
PNP0000: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0000: end config
pnpbios: handle 10 device ID PNP0000 (0000d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
PNP0100: end config
pnpbios: handle 11 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
PNP0b00: end config
pnpbios: handle 12 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
PNP0303: end config
pnpbios: handle 13 device ID PNP0303 (0303d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xf0, size=0x1, align=0
PNP0c04: end config
pnpbios: handle 14 device ID PNP0c04 (040cd041)
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x80-0x90, size=0x11, align=0
PNP0200: adding io range 0x94-0x9f, size=0xc, align=0
PNP0200: adding io range 0xc0-0xde, size=0x1f, align=0
PNP0200: end config
pnpbios: handle 15 device ID PNP0200 (0002d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
PNP0800: end config
pnpbios: handle 16 device ID PNP0800 (0008d041)
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: end config
pnpbios: handle 17 device ID PNP0a03 (030ad041)
PNP0c02: adding io range 0x290-0x297, size=0x8, align=0
PNP0c02: adding io range 0x3f0-0x3f1, size=0x2, align=0
PNP0c02: adding io range 0xe400-0xe47f, size=0x80, align=0
PNP0c02: adding io range 0xec00-0xec3f, size=0x40, align=0
PNP0c02: end config
pnpbios: handle 18 device ID PNP0c02 (020cd041)
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc-: sc0 exists, using next available unit number
vga-: vga0 exists, using next available unit number
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata2 failed to probe at port 0x1f0 irq 14 on isa0
ata3: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata3: mask=03 status0=00 status1=00
ata3: mask=03 status0=00 status1=00
ata3: devices = 0x0
ata3: probe allocation failed
ata3 failed to probe at port 0x170-0x177,0x376 irq 15 on isa0
adv0 failed to probe on isa0
bt0 failed to probe on isa0
aha0 failed to probe on isa0
aic0 failed to probe on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 00 00 64
psm: status 00 03 64
psm: status 00 03 64
psm: data 08 00 00
psm: status 10 00 64
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
vt0 failed to probe on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: IEEE1284 device found
Probing for PnP devices on ppbus0:
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ed0 failed to probe at port 0x280 iomem 0xd8000 irq 10 on isa0
cs0 failed to probe at port 0x300 on isa0
sn0 failed to probe at port 0x300 irq 10 on isa0
ie0 failed to probe at port 0x300 iomem 0xd0000 irq 10 on isa0
fe0 failed to probe at port 0x300 on isa0
le0 failed to probe at port 0x300 iomem 0xd0000 irq 5 on isa0
lnc0 failed to probe at port 0x280 irq 10 drq 0 on isa0
sc1: no video adapter is found.
sc1: <System console> failed to probe on isa0
vga1: <Generic ISA VGA> failed to probe on isa0
isa_probe_children: probing PnP devices
unknown: <PNP0401> can't assign resources
unknown: <PNP0401> at port 0x378-0x37f on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0501> can't assign resources
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNP0700> can't assign resources
unknown: <PNP0700> at port 0x3f2-0x3f5 on isa0
unknown: <PNPb02f> failed to probe at port 0x200-0x207 on isa0
unknown: <PNP0f13> can't assign resources
unknown: <PNP0f13> at irq 12 on isa0
unknown: <INT0800> failed to probe at iomem 0xffb80000-0xffbfffff on isa0
unknown: <PNP0303> can't assign resources
unknown: <PNP0303> at port 0x60 on isa0
unknown: <PNP0800> failed to probe at port 0x61 on isa0
unknown: <PNP0c02> can't assign resources
unknown: <PNP0c02> at port 0x290-0x297,0x3f0-0x3f1 on isa0
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
bpf: ppp0 attached
new masks: bio 684040, tty 63109a, net 67109a
IP packet filtering initialized, divert disabled, rule-based forwarding enabled, default to deny, unlimited logging
ata0-master: DMA limited to UDMA33, non-ATA66 compliant cable
ata0-master: success setting up UDMA2 mode on ICH chip
ad0: <WDC WD153BA/16.13M16> ATA-4 disk at ata0 as master
ad0: 14669MB (30043440 sectors), 29805 cyls, 16 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=4 cblid=0
Creating DISK ad0
ata0-slave: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata0-slave: success setting up WDMA2 mode on ICH chip
acd0: <CD-RW CRX100E/1.0j> CD-RW drive at ata0 as slave
acd0: read 4134KB/s (4134KB/s) write 689KB/s (689KB/s), 1024KB buffer, WDMA2
acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
acd0: Writes: CD-R, CD-RW, test write
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: CD-ROM 120mm data disc loaded, unlocked
Mounting root from ufs:/dev/ad0s2a
ad0s1: type 0x6, start 63, end = 4160834, size 4160772 : OK
ad0s2: type 0xa5, start 13607055, end = 27969164, size 14362110 : OK
ad0s3: type 0x7, start 27969165, end = 30041549, size 2072385 : OK
ad0s4: type 0x5, start 4160835, end = 13607054, size 9446220 : OK
ad0s5: type 0xb, start 4160898, end = 13607054, size 9446157 : OK
start_init: trying /sbin/init
link_elf: symbol ether_input undefined
Linux-ELF exec handler installed
pid 134 (ldconfig), uid 0: exited on signal 11 (core dumped)
link_elf: symbol ktrgenio undefined
splash: image decoder found: green_saver
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000806214752.13308.qmail>