Date: Sun, 27 Aug 2000 13:48:17 -0700 From: Kent Stewart <kstewart@urx.com> To: "Herbert J. Skuhra" <herbert@gmx.at> Cc: freebsd-questions@FreeBSD.ORG, freebsd-stable@FreeBSD.ORG Subject: Re: ata0-slave doesn't show up! Message-ID: <39A97E91.D5CC1018@urx.com> References: <20000827120008.A73952@freebsd2.rocks> <009201c0105d$5963f5a0$cd430ace@mark8> <20000827223938.A993@freebsd2.rocks>
next in thread | previous in thread | raw e-mail | index | archive | help
"Herbert J. Skuhra" wrote: > > Hi Josh and thanks a lot for your reply! > > I am running now 4.1-STABLE userland (built yesterday) and the original > kernel that comes with the 4.1-RELEASE installation. It doesn't work this way. You are lucky you can even run anything. If you cvsup, you build both the userland and the kernel. You also have to pay attention to how you build the kernel. You do that by following the receipe in /usr/src/UPDATING. It is missing a mergemaster command after the installworld. Kent > > Here is the output of uname -a: > > FreeBSD freebsd2.rocks 4.1-RELEASE FreeBSD 4.1-RELEASE #0: Fri Jul 28 > 14:30:31 GMT 2000 jkh@ref4.freebsd.org:/usr/src/sys/compile/GENERIC > i386 > > Here are the important lines of dmesg: > > atapci0: <AcerLabs Aladdin ATA33 controller> port 0xb800-0xb80f irq 0 > at device 15.0 on pci0 > ata0: at 0x1f0 irq 14 on atapci0 > ata1: at 0x170 irq 15 on atapci0 > ad0: 19536MB <ST320423A> [39693/16/63] at ata0-master using UDMA33 > ad1: 19536MB <ST320423A> [39693/16/63] at ata0-slave using UDMA33 > ata1-master: DMA limitted to UDMA33, non-ATA66 compliant cable > ad2: 14664MB <IBM-DJNA-351520> [29795/16/63] at ata1-master using UDMA33 > acd0: CDROM <ASUS CD-S500/A> at ata1-slave using PIO4 > > And finally the df-output, that shows mounted filesystems from each of > my three hard disks: > > Filesystem 1K-blocks Used Avail Capacity Mounted on > /dev/ad0s1a 74383 36075 32358 53% / > /dev/ad0s1g 1488607 551345 818174 40% /home > /dev/ad0s1h 2977230 984905 1754147 36% /usr > /dev/ad0s1d 3020518 416766 2362111 15% /usr/local > /dev/ad0s1f 124015 5392 108702 5% /var > procfs 4 4 0 100% /proc > /dev/ad1s1e 6944186 2151210 4237442 34% /mnt/disk0 > /dev/ad1s3e 12440776 1691453 9754061 15% /mnt/disk1 > /dev/ad2s2f 9091795 6402416 1962036 77% /mnt/disk3 > /dev/ad2s2e 1488607 619052 750467 45% /mnt/disk4 > > I guess that shows that my hard disks are connected correctly and that > all are in an healthy condition or let's say not dead :). > > Ok, as I stated earlier every kernel I built from the 4.1-STABLE (also > GENERIC) sources doesn't bring up ata0-slave aka ad1. > > Guys, do you think this is a bug? Should I send-pr or wait? > > Best Regards, > Herbert > > * Josh Paetzel (jpaetzel@hutchtel.net) [000827 22:04]: > > > > That is really odd. GENERIC should work just fine for picking up both the > > master and slave on both controllers. You are sure the drive didn't die on > > you or anything like that, aren't you? > > > > I haven't heard anyone else have this problem. You may have a genuine > > FreeBSD bug on your hands. Someone more knowledgeable than I may know > > something about this, but if you don't get a response you should send in a > > pr. > > To Unsubscribe: send mail to majordomo@FreeBSD.org > with "unsubscribe freebsd-questions" in the body of the message -- Kent Stewart Richland, WA mailto:kbstew99@hotmail.com http://kstewart.urx.com/kstewart/index.html FreeBSD News http://daily.daemonnews.org/ To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?39A97E91.D5CC1018>