Date: Thu, 14 Feb 2002 16:11:23 +0100 (CET) From: marcov@stack.nl (Marco van de Voort) To: freebsd-mobile@freebsd.org Subject: pccard not recognised by 4.5 succesfully installed Message-ID: <20020214151123.CC2E09631@toad.stack.nl>
next in thread | raw e-mail | index | archive | help
I got the "Dynalink lc100c16" pcmcia card working using 4.5, and though
a trivial exercise (20 minutes, no previous pcmcia exposure), I though the
info could be useful for auto detection in later versions.
Note: I'm not subscribed to this list, if somebody needs extra data/wants
me to perform tests (Notebook: Dell cpi 233), please mail me directly.
Vendor: Dynalink (Tulip.com all over the box??!?)
card lc100c16 (16 bit 10/100 UTP)
Award winning pccard.conf data:
card "Dynalink" "L100C16"
config auto "ed0" ? 0x9
insert /etc/pccard_ether ed0 link0 -link1
remove /sbin/ifconfig ed0 delete
dumpcis: (for people that know what to look for)
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x15 (Version 1 info), length = 26
000: 04 01 44 79 6e 61 6c 69 6e 6b 00 4c 31 30 30 43
010: 31 36 00 56 00 31 2e 30 00 ff
Version = 4.1, Manuf = [Dynalink], card vers = [L100C16]
Addit. info = [V],[1.0]
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
000: ff ff 90 10
PCMCIA ID = 0xffff, OEM ID = 0x1090
Tuple #4, code = 0x1a (Configuration map), length = 5
000: 01 01 c0 03 63
Reg len = 2, config register addr = 0x3c0, last config = 0x1
Registers: XX---XX-
Tuple #5, code = 0x1b (Configuration entry), length = 11
000: c7 81 19 07 55 4d 5d 65 30 ff ff
Config index = 0x7(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Card decodes 5 address lines, full 8/16 Bit I/O
IRQ modes: Level
IRQs: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
Tuple #6, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 00 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x300 block length = 0x20
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 20 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x320 block length = 0x20
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 40 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 60 03 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x360 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 00 02 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x200 block length = 0x20
Tuple #11, code = 0x1b (Configuration entry), length = 7
000: 07 08 ca 60 20 02 1f
Config index = 0x7
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x220 block length = 0x20
Tuple #12, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #13, code = 0x22 (Functional EXT), length = 2
000: 01 02
Network technology: Ethernet
Tuple #14, code = 0x22 (Functional EXT), length = 2
000: 02 64
Wrong length for network extension tuple
Tuple #15, code = 0x22 (Functional EXT), length = 2
000: 03 01
Network media: UTP
Tuple #16, code = 0xff (Terminator), length = 0
2 slots found
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20020214151123.CC2E09631>