Date: Tue, 13 Mar 2001 20:33:13 -0800 From: "Clint Martin" <clintm@cet.com> To: "FreeBSD Questions" <FREEBSD-QUESTIONS@freebsd.org> Subject: Help with TAPE DRIVE Message-ID: <003801c0ac3f$e1ed0d20$0264000a@helter.org>
next in thread | raw e-mail | index | archive | help
Hello, I am having dificulties making my HP Colorado IDE 14GB Tape drive work.. It used to work, but now I cannot even make it rewind/Re-Tension the tape I think I could figgure out what exactally the problem is if somebody could point me in the direction of what This Means: wst_rewind: wst0: i/o error, status=51<ready,opdone,check>, error=0 total=0 ERR=8 len=-1057468957 ASC=80 ASCQ=d5 The machine is a K6-2 350 W/64M Ram, running FreeBSD 3.3 Release. Heres the output from dmesg: -------------------------------------------------------------------------- > > FreeBSD 3.3-RELEASE #0: Wed Nov 10 23:04:07 PST 1999 > > Timecounter "i8254" frequency 1193182 Hz > > Timecounter "TSC" frequency 350796527 Hz > > CPU: AMD-K6(tm) 3D processor (350.80-MHz 586-class CPU) > > Origin = "AuthenticAMD" Id = 0x58c Stepping = 12 > > Features=0x8021bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,PGE,MMX> > > AMD Features=0x80000800<SYSCALL,3DNow!> > > real memory = 67043328 (65472K bytes) > > avail memory = 62406656 (60944K bytes) > > Preloaded elf kernel "kernel" at 0xc029c000. > > Preloaded userconfig_script "/boot/kernel.conf" at 0xc029c09c. > > Probing for devices on PCI bus 0: > > chip0: <AcerLabs M1541 (Aladdin-V) PCI host bridge> rev 0x04 on pci0.0.0 > > chip1: <AcerLabs M5243 PCI-PCI bridge> rev 0x04 on pci0.1.0 > > chip2: <PCI to 0x80 bridge (vendor=10b9 device=7101)> rev 0x00 on pci0.3.0 > > chip3: <AcerLabs M1533 portable PCI-ISA bridge> rev 0xc3 on pci0.7.0 > > de0: <Digital 21041 Ethernet> rev 0x11 int a irq 10 on pci0.10.0 > > de0: 21041 [10Mb/s] pass 1.1 > > de0: address 00:c0:f0:04:0d:0c > > xl0: <3Com 3c905B-TX Fast Etherlink XL> rev 0x30 int a irq 11 on pci0.11.0 > > xl0: Ethernet address: 00:10:5a:ac:04:3d > > xl0: autoneg complete, link status good (full-duplex, 100Mbps) > > ide_pci0: <Acer Aladdin IV/V (M5229) Bus-master IDE controller> rev 0xc1 int a irq 0 on pci0.15.0 > > Probing for devices on PCI bus 1: > > Probing for PnP devices: > > Probing for devices on the ISA bus: > > sc0 on isa > > sc0: MDA/Hercules <16 virtual consoles, flags=0x0> > > atkbdc0 at 0x60-0x6f on motherboard > > atkbd0 irq 1 on isa > > psm0 not found > > sio0 at 0x3f8-0x3ff irq 4 flags 0x10 on isa > > sio0: type 16550A > > sio1 at 0x2f8-0x2ff irq 3 on isa > > sio1: type 16550A > > fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa > > fdc0: FIFO enabled, 8 bytes threshold > > fd0: 1.44MB 3.5in > > wdc0 at 0x1f0-0x1f7 irq 14 on isa > > wdc0: unit 0 (wd0): <Maxtor 90288D2> > > wd0: 2747MB (5627664 sectors), 5583 cyls, 16 heads, 63 S/T, 512 B/S > > wdc0: unit 1 (wd1): <ST32122A> > > wd1: 2014MB (4124736 sectors), 4092 cyls, 16 heads, 63 S/T, 512 B/S > > wdc1 at 0x170-0x177 irq 15 on isa > > wdc1: unit 0 (atapi): <HP COLORADO 14GB/4.000026>, removable, intr, > > dma, iordis > > wst0: Drive empty, reverse, eformat, qfa, ecc, 512b > > wst0: Max speed=0Kb/s, Transfer limit=64 blocks, Buffer size=864 blocks > > wdc1: unit 1 (atapi): <CD-ROM 32X/AKU/U10A>, removable, intr, dma, iordis > > acd0: drive speed 0 - 5500KB/sec, 128KB cache > > acd0: supported read types: CD-DA > > acd0: Audio: play, 255 volume levels > > acd0: Mechanism: ejectable tray > > acd0: Medium: no/blank disc inside, unlocked > > ppc0 at 0x3bc irq 7 flags 0x40 on isa > > ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode > > lpt0: <generic printer> on ppbus 0 > > lpt0: Interrupt-driven port > > ppi0: <generic parallel i/o> on ppbus 0 > > vga0 at 0x3b0-0x3bb maddr 0xb0000 msize 32768 on isa > > npx0 on motherboard > > npx0: INT 16 interface > > > > -------------------------------------------------------------------------- And here the output describes the error messages that I've been getting while attempting to get the Darn thing to work... > > ------------------------------------------------------------------------- > > wst_rewind: wst0: i/o error, status=51<ready,opdone,check>, error=0 > > total=0 ERR=8 len=-1057468957 ASC=80 ASCQ=d5 > > wst0: 0d total bytes transferred > > wst_rewind: wst0: i/o error, status=51<ready,opdone,check>, error=0 > > total=0 ERR=8 len=-1057468957 ASC=80 ASCQ=d5 > > wst0: 0d total bytes transferred > > wst0: 0d total bytes transferred > > wst0: Unknown media (0x85), reverse, eformat, qfa, ecc, 512b > > wst0: Max speed=0Kb/s, Transfer limit=64 blocks, Buffer size=864 blocks > > wst0: 0d total bytes transferred > > wst0: 0d total bytes transferred > > wst_rewind: wst0: i/o error, status=51<ready,opdone,check>, error=0 > > total=0 ERR=8 len=-1057444518 ASC=80 ASCQ=d5 > > wst0: 0d total bytes transferred > > wst_rewind: wst0: i/o error, status=51<ready,opdone,check>, error=0 > > total=0 ERR=8 len=-1057444518 ASC=80 ASCQ=d5 > > wst0: 0d total bytes transferred > > wst_rewind: wst0: i/o error, status=51<ready,opdone,check>, error=0 > > total=0 ERR=8 len=-1057444518 ASC=80 ASCQ=d5 > > wst0: 0d total bytes transferred > > wst0: 0d total bytes transferred > > cd9660: RockRidge Extension > > de0: promiscuous mode enabled > > wst_rewind: wst0: i/o error, status=51<ready,opdone,check>, error=0 > > total=0 ERR=8 len=-1057460793 ASC=80 ASCQ=d5 > > wst0: 0d total bytes transferred > > wst0: 0d total bytes transferred > > wst_rewind: wst0: i/o error, status=51<ready,opdone,check>, error=0 > > total=0 ERR=8 len=-1057440309 ASC=80 ASCQ=d5 > > wst0: 0d total bytes transferred > > > > as you can see the system detects the drive.. When I type: mt -f /dev/rwst0 status I get: > > Mode Density Blocksize bpi Compression > > Current: 0x01:X3.22-1983 512 bytes 800 none > > ---------available modes--------- > > 0: default variable 0 none > > 1: default variable 0 none > > 2: default variable 0 none > > 3: default variable 0 none > > --------------------------------- > > File Number: 0 Record Number: 0 I am really baffled, any help would be appreciated.. Clint To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?003801c0ac3f$e1ed0d20$0264000a>