Date: Tue, 14 Jan 2003 21:18:39 +0000 From: "mark" <reveille@burntmail.com> To: "Vince Vielhaber" <vev@michvhf.com> Cc: freebsd-mobile@freebsd.org Subject: Re: wi troubles, error Message-ID: <W779677702145631042579119@burntmail>
next in thread | raw e-mail | index | archive | help
by setting my pccard_mem to 0xd8000, it finally read the cis data from my card correctly. It dumped:
Configuration data for card in slot
Tuple #1, code = 0x17 (Attribute memory descriptor), length = 3
000: d9 01 ff
Attribute memory device information:
Device number 1, type Function specific, WPS ON
Speed: 250nS, Memory block size = 2Kb, 1 Units
Tuple #2, Code = 0x1d (Other conditions for attribute memory), length = 4
000: 03 d9 01 ff
(MWAIT) (3V card)
Tuple #3, Code = 0x20 (Manufacturer ID), length = 4
000: bf 01 02 33
PCMCIA ID = 0x1bf, OEM ID = 03302
Tuple #4, code 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #5, code = 0x15 (Version 1 info), length = 51
(hex)
Version = 5.0, Manf = [Belkin], card vers = [11Mbps-Wireless-Notebook-Network-Adapter]
Tuple #6, code=0x1a (Configuration map), length = 6
000: 01 02 00 08 01 ff
Reg len = 2, config register addr = 0x800, last config - 0x2
Registers: X------- 1 bytes in subtubles
Tuple #7, code = 0x1b (Configuration entry), length = 15
000: c1 81 9d 71 55 2e 2e 2d fc 14 45 10 b8 ff 20
Config index = 0x1(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage : 5 x 1V
(more power current information)...
Wait scale Speed = 1.2 x 10 us
Card decodes 5 addresses lines, limited 8/16 Bit I/O
IRQ modes:
IRQs: 3 4 5 8 9 10 11 12 13 14 15
Max twin cards = 0
Misc attr: (Power down suipported)
Tuple #8, code = 0xff (Terminator), length = 0
2 slots found.
I configured the following (using the dumped data as my resource) into /etc/pccard.conf:
card "Belkin" "11Mbps-Wireless-Notebook-Network-Adapter"
config auto "wi" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
..does that look right? when I insert the card, I get a rather odd error, which is:
pccard: card inserted, slot 1
wi0 at port 0x240-0x27f irq 10 slot 1 on pccard1
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: init failed
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: timeout in wi_cmd 0x0021; event status 0x0000
wi0: mac read failed 5
device_probe_and_attach: wi0 attached returned 5
what am I doing wrong?
Thanks,
Mark
>-----Original Message-----
>From: Vince Vielhaber [mailto:vev@michvhf.com]
>Sent: Tuesday, January 14, 2003 07:14 PM
>To: 'mark'
>Cc: freebsd-mobile@freebsd.org
>Subject: Re: wi ultimate crisis
>
>On Tue, 14 Jan 2003, mark wrote:
>
>> I had those two lines in my rc.conf (pccard_enable="YES" and pccard_beep="1")
>> #pccardc dumpcis
>> Read return -1 bytes (expected 2)
>> pccardc: CIS code read: Cannot allocate memory
>> Read return -1 bytes (expected 10)
>> Configuration data for card in slot 0
>> 2 slots found
>>
>>
>> if I add the line "pccard_mem=0x10000" and reboot I get this for pccardc dumpcis. note: i had the card inserted in the 2nd pcmcia slot:
>
>I recently ran into something similar. man pccardc told me this (after
>I tried a few other addresses and finally looked it up):
>
>
> 5. pccardmem addr
>
> Specifies the host address using PC-CARD controller(PCIC) will use
> to map cards to. Because the PCIC needs a contiguous 16KB memory,
> you can only use the following four addresses:
>
> 0xd0000 0xd0000-0xd3fff (default)
> 0xd4000 0xd4000-0xd7fff
> 0xd8000 0xd8000-0xdbfff
> 0xdc000 0xdc000-0xdffff
>
> You can use "DEFAULT" instead of 0xd0000. This subcommand corre-
> sponds to pccard_mem in rc.conf(5).
>
>So one of those four addresses in the pccard_mem= should get you a bit
>further.
>
>Vince.
>--
> Fast, inexpensive internet service 56k and beyond! http://www.pop4.net/
> http://www.meanstreamradio.com http://www.unknown-artists.com
> Internet radio: It's not file sharing, it's just radio.
>
>
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?W779677702145631042579119>