Date: Fri, 5 Nov 1999 04:46:28 -0700 From: "Dragon Knight ][" <dragonk@dragonknight.yi.org> To: freebsd-questions@freebsd.org Cc: dragonk@mato.com Subject: Rage 128 Linux X Server Message-ID: <19991105044628.A640@dragonknight.yi.org>
next in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
Reply-to: dragonk@mato.com
I am having some difficulties in getting a Linux X server to run
properly. I have included the output from startx and will attach
my XF86Config. Here is my setup. ATI All-In-Wonder 128 PCI Board
with 16 MB RAM. I retrieved the X Server from www.suse.de/en/
support/xsuse/ . Per the instructions I downloaded and installed
the server (After installing linux_base, etc.) I needed to
download the fix for older glibc based systems and apply it. I
also had to make a symlink from /dev/ttyvb to /dev/tty00 and
/dev/tty13 as it gave me errors otherwise.
When the X server is run I get the error:
xf86OpenConsole: VT_ACTIVATE failed
but when fed a CTRL+C it will continue to load. The nice
GUI flashes for a second and then X shuts down.
This is a (as of today) 3.3-STABLE box.
Any idea's would be greatly appreciated.
XFCom_Rage128 Version 1.3/ X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: 6 September 1999
If the server is older than 6-12 months, or if your card is newer
than the above date, look for a newer version before reporting
problems. Please report problems to x@suse.de
Operating System: Linux 2.2.5 i686 [ELF]
Configured drivers:
SVGA: server for SVGA graphics adaptors (Patchlevel 0):
rage128
(using VT number 13)
XF86Config: /etc/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: disabled
(**) XKB: keymap: "xfree86(us)" (overrides other XKB settings)
(**) Mouse: type: SysMouse, device: /dev/sysmouse, buttons: 3
(**) Mouse: 3 button emulation (timeout: 50ms)
(**) SVGA: Graphics device ID: "All-Wonder-128"
(**) SVGA: Monitor ID: "My Monitor"
(--) SVGA: Mode "1280x1024" needs hsync freq of 64.25 kHz. Deleted.
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/local/,/usr/X11R6/lib/X11/fonts/m
xf86OpenConsole: VT_ACTIVATE failed
It seems to hang here, feeding it a CTRL+C lets you continue....
xinit: Resource temporarily unavailable (errno 35): unexpected signal 2^M
xf86OpenConsole: VT_WAITACTIVE failed
(--) SVGA: PCI: ATI Rage128 RE rev 0, Memory @ 0xe4000000, 0xeb000000, I/O @ 0xa
(--) SVGA: Found ATI Rage 128 RE chip
(--) SVGA: chipset: rage128
(**) SVGA: videoram: 16384k
(**) SVGA: clocks: 25.00 28.00 40.00 0.00 50.00 77.00 36.00 45.00
(**) SVGA: clocks: 130.00 120.00 80.00 31.00 110.00 65.00 75.00 94.00
(**) SVGA: Option "dac_8_bit"
(**) SVGA: Using 32 bpp, Depth 24, Color weight: 888
(--) SVGA: Maximum allowed dot-clock: 250.000 MHz
(**) SVGA: Mode "1280x1024": mode clock = 80.000
(**) SVGA: Mode "1152x864": mode clock = 92.000
(**) SVGA: Mode "1024x768": mode clock = 85.000
(**) SVGA: Mode "800x600": mode clock = 69.650
(--) SVGA: Virtual resolution set to 1280x1024
(--) SVGA: SpeedUp code selection modified because virtualX != 1024
waiting for X server to shut down (--) SVGA: Using XAA (XFree86 Acceleration Arc
(--) SVGA: XAA: Solid filled rectangles
(--) SVGA: XAA: Screen-to-screen copy
(--) SVGA: XAA: 8x8 color expand pattern fill
(--) SVGA: XAA: Indirect CPU to screen color expansion (imagetext, polytext)
(--) SVGA: XAA: Using 10 128x128 areas for pixmap caching
(--) SVGA: XAA: Caching tiles and stipples
(--) SVGA: XAA: Horizontal and vertical lines and segments
..
[-- Attachment #2 --]
# Copyright (c) 1995 by The XFree86 Project, Inc.
#
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
# If you don't have a floating point coprocessor and emacs, Mosaic or other
# programs take long to start up, try moving the Type1 and Speedo directory
# to the end of this list (or comment them out).
#
FontPath "/usr/X11R6/lib/X11/fonts/local/"
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/:unscaled"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
# For OSs that support Dynamically loaded modules, ModulePath can be
# used to set a search path for the modules. This is currently supported
# for Linux ELF, FreeBSD 2.x and NetBSD 1.x. The default path is shown
# here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Module section -- this is an optional section which is used to specify
# which dynamically loadable modules to load. Dynamically loadable
# modules are currently supported only for Linux ELF, FreeBSD 2.x
# and NetBSD 1.x. Currently, dynamically loadable modules are used
# only for some extended input (XInput) device drivers.
# **********************************************************************
#
# Section "Module"
#
# This loads the module for the Joystick driver
#
# Load "xf86Jstk.so"
#
# EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# NoTrapSignals
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# DontZap
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# DontZoom
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# DisableVidModeExtension
# Uncomment this to enable the use of a non-local xvidtune client.
# AllowNonLocalXvidtune
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# DisableModInDev
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# AllowNonLocalModInDev
EndSection
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Keyboard section
# **********************************************************************
Section "Keyboard"
Protocol "Standard"
# when using XQUEUE, comment out the above line, and uncomment the
# following line
# Protocol "Xqueue"
AutoRepeat 500 5
# Let the server do the NumLock processing. This should only be required
# when using pre-R6 clients
# ServerNumLock
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
# Xleds 1 2 3
# To set the LeftAlt to Meta, RightAlt key to ModeShift,
# RightCtl key to Compose, and ScrollLock key to ModeLock:
# LeftAlt Meta
# RightAlt ModeShift
# RightCtl Compose
# ScrollLock ModeLock
# To disable the XKEYBOARD extension, uncomment XkbDisable.
XkbDisable
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults). For example, for a non-U.S.
# keyboard, you will probably want to use:
# XkbModel "pc102"
# If you have a US Microsoft Natural keyboard, you can use:
# XkbModel "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
# XkbLayout "de"
# or:
# XkbLayout "de"
# XkbVariant "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
# XkbOptions "ctrl:swapcaps"
# These are the default XKB settings for XFree86
# XkbRules "xfree86"
# XkbModel "pc101"
# XkbLayout "us"
# XkbVariant ""
# XkbOptions ""
XkbKeymap "xfree86(us)"
EndSection
# **********************************************************************
# Pointer section
# **********************************************************************
Section "Pointer"
Protocol "SysMouse"
Device "/dev/sysmouse"
# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.
# Protocol "Xqueue"
# Baudrate and SampleRate are only for some Logitech mice
# or for the AceCad tablets which require 9600 baud
# BaudRate 9600
# SampleRate 150
# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
Emulate3Buttons
Emulate3Timeout 50
# ChordMiddle is an option for some 3-button Logitech mice
# ChordMiddle
EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "My Monitor"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 36-64
VertRefresh 50-100
# 800x600 @ 60 Hz, 37.8 kHz hsync
Modeline "800x600" 40 800 840 968 1056 600 601 605 628 +hsync +vsync
# 1152x864 @ 89 Hz interlaced, 44 kHz hsync
ModeLine "1152x864" 65 1152 1168 1384 1480 864 865 875 985 Interlace
# 800x600 @ 72 Hz, 48.0 kHz hsync
Modeline "800x600" 50 800 856 976 1040 600 637 643 666 +hsync +vsync
# 1024x768 @ 60 Hz, 48.4 kHz hsync
Modeline "1024x768" 65 1024 1032 1176 1344 768 771 777 806 -hsync -vsync
# 1152x864 @ 60 Hz, 53.5 kHz hsync
Modeline "1152x864" 89.9 1152 1216 1472 1680 864 868 876 892 -HSync -VSync
# 800x600 @ 85 Hz, 55.84 kHz hsync
Modeline "800x600" 60.75 800 864 928 1088 600 616 621 657 -HSync -VSync
# 1024x768 @ 70 Hz, 56.5 kHz hsync
Modeline "1024x768" 75 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
# 1280x1024 @ 87 Hz interlaced, 51 kHz hsync
Modeline "1280x1024" 80 1280 1296 1512 1568 1024 1025 1037 1165 Interlace
# 800x600 @ 100 Hz, 64.02 kHz hsync
Modeline "800x600" 69.65 800 864 928 1088 600 604 610 640 -HSync -VSync
# 1024x768 @ 76 Hz, 62.5 kHz hsync
Modeline "1024x768" 85 1024 1032 1152 1360 768 784 787 823
# 1152x864 @ 70 Hz, 62.4 kHz hsync
Modeline "1152x864" 92 1152 1208 1368 1474 864 865 875 895
# 1280x1024 @ 61 Hz, 64.2 kHz hsync
Modeline "1280x1024" 110 1280 1328 1512 1712 1024 1025 1028 1054
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
Section "Device"
Identifier "All-Wonder-128"
VendorName "ATI"
BoardName "Rage128/VidCap"
VideoRam 16384
Ramdac "rage128"
Option "dac_8_bit"
Clocks 25.0 28.0 40.0 0.0 50.0 77.0 36.0 45.0
Clocks 130.0 120.0 80.0 31.0 110.0 65.0 75.0 94.0
EndSection
Section "Screen"
Driver "svga"
Device "All-Wonder-128"
Monitor "My Monitor"
Subsection "Display"
Depth 32
Modes "1280x1024" "1152x864" "1024x768" "800x600"
ViewPort 0 0
EndSubsection
EndSection
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?19991105044628.A640>