Date: Thu, 7 Nov 2013 00:29:25 +0100 (CET) From: "Peter Cornelius" <pcc@gmx.net> To: freebsd-arm@freebsd.org Subject: Built world on RPI-B, ports pending Message-ID: <trinity-30dc2f81-d5ac-4f77-b663-116a12bfc461-1383780565220@3capp-gmx-bs32>
next in thread | raw e-mail | index | archive | help
To whom it may concern, I just want to give some feedback on the Raspberry Pi in that I just completed a kernel and world build and install (both over NFS and using the current RPI-B config file) successfully this morning (or rather, last night ;-)), and just rebooted into that kernel world more or less happily. The version I started with was FreeBSD raspberry-pi 11.0-CURRENT FreeBSD 11.0-CURRENT #0 r257540: Sat Nov 2 11:14:36 CET 2013 root@petra:/usr/obj/RaspberryPI/arm.armv6/usr/SVN/FreeBSD/base/head/sys /RPI-B arm (which, in turn, I built on FreeBSD petra.cornelius 9.2-STABLE FreeBSD 9.2-STABLE #7 r256090: Sun Oct 6 23:14:25 CEST 2013 root@petra:/usr/obj/usr/SVN/FreeBSD/base/stable/9/sys/PETRA amd64, installed on a mem card and booted the RPI from). uname at the RPI now reports FreeBSD raspberry-pi 11.0-CURRENT FreeBSD 11.0-CURRENT #0: Tue Nov 5 20:03:46 UTC 2013 pi@raspberry-pi:/usr/obj/usr/src/sys/RPI-B arm I don't know (yet?) why the SVN version is missing, but I believe it is the following SVN release I have. Path: /usr/SVN/FreeBSD/base/head Working Copy Root Path: /usr/SVN/FreeBSD/base/head URL: https://svn0.us-east.freebsd.org/base/head Relative URL: ^/head Repository Root: https://svn0.us-east.freebsd.org/base Repository UUID: ccf9f872-aa2e-dd11-9fc8-001c23d0bc1f Revision: 257540 Node Kind: directory Schedule: normal Last Changed Author: delphij Last Changed Rev: 257539 Last Changed Date: 2013-11-02 02:16:10 +0100 (Sat, 02 Nov 2013) I paste dmesg further below for your entertainment. Upcoming issue for me to figure out is why pkg_* fails, though the binaries are recently built (though I believe that this I have seen for a couple of weeks or so hence it's not new), hoping to get back to building ports. One just needs to be mildly patient since the RPI's primary savings are on price and energy but less so on buildworld time and the like :) I appreciate everyone's work on the box and hope that this mail creates more enthusiasm rather than inbox consumption. I am willing to share the little I know but please appreciate if I may be a bit slow responding, at times. Best 73 es gn, Peter. --- Pasted dmesg follows. --- KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2013 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 11.0-CURRENT #0: Tue Nov 5 20:03:46 UTC 2013 pi@raspberry-pi:/usr/obj/usr/src/sys/RPI-B arm FreeBSD clang version 3.3 (tags/RELEASE_33/final 183502) 20130610 CPU: ARM1176JZ-S rev 7 (ARM11J core) Supported features: ARM_ISA THUMB2 JAZELLE ARMv4 Security_Ext WB enabled LABT branch prediction enabled 16KB/32B 4-way instruction cache 16KB/32B 4-way write-back-locking-C data cache real memory = 536870912 (512 MB) avail memory = 385458176 (367 MB) kbd0 at kbdmux0 random: <Software, Yarrow> initialized fdtbus0: <Flattened Device Tree> simplebus0: <Flattened device tree simple bus> mem 0x20000000-0x20ffffff on fdtbus0 intc0: <BCM2835 Interrupt Controller> mem 0x2000b200-0x2000b3ff on simplebus0 systimer0: <BCM2835 System Timer> mem 0x20003000-0x20003fff irq 8,9,10,11 on simplebus0 Event timer "BCM2835 Event Timer 3" frequency 1000000 Hz quality 1000 Timecounter "BCM2835 Timecounter" frequency 1000000 Hz quality 1000 bcmwd0: <BCM2708/2835 Watchdog> mem 0x2010001c-0x20100027 on simplebus0 gpio0: <BCM2708/2835 GPIO controller> mem 0x20200000-0x202000af irq 57,59,58,60 on simplebus0 gpio0: read-only pins: 46,47,48,49,50,51,52,53. gpio0: reserved pins: 48,49,50,51,52,53. gpioc0: <GPIO controller> on gpio0 gpiobus0: <GPIO bus> on gpio0 iichb0: <BCM2708/2835 BSC controller> mem 0x20205000-0x2020501f irq 61 on simplebus0 iicbus0: <OFW I2C bus> on iichb0 iic0: <I2C generic I/O> on iicbus0 iichb1: <BCM2708/2835 BSC controller> mem 0x20804000-0x2080401f irq 61 on simplebus0 iicbus1: <OFW I2C bus> on iichb1 iic1: <I2C generic I/O> on iicbus1 spi0: <BCM2708/2835 SPI controller> mem 0x20204000-0x2020401f irq 62 on simplebus0 spibus0: <OFW SPI bus> on spi0 bcm_dma0: <BCM2835 DMA Controller> mem 0x20007000-0x20007fff,0x20e05000-0x20e05fff irq 24,25,26,27,28,29,30,31,32,33,34,35,36 on simplebus0 mbox0: <BCM2835 VideoCore Mailbox> mem 0x2000b880-0x2000b8bf irq 1 on simplebus0 sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x20300000-0x203000ff irq 70 on simplebus0 mmc0: <MMC/SD bus> on sdhci_bcm0 uart0: <PrimeCell UART (PL011)> mem 0x20201000-0x20201fff irq 65 on simplebus0 dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0x20980000-0x2099ffff irq 17 on simplebus0 usbus0 on dwcotg0 fb0: <BCM2835 framebuffer device> on fdtbus0 sc0: Unknown <16 virtual consoles, flags=0x300> simplebus1: <Flattened device tree simple bus> on fdtbus0 Timecounters tick every 10.000 msec usbus0: 480Mbps High Speed USB v2.0 ugen0.1: <DWCOTG> at usbus0 uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 mmcsd0: 16GB <SDHC 00000 1.0 SN 201172550 MFG 02/2012 by 27 SM> at mmc0 50.0MHz/4bit/65535-block fb0: 1280x1024(0x0@0,0) 16bpp fb0: pitch 2560, base 0x58006000, screen_size 2621440 random: unblocking device. Root mount waiting for: usbus0 uhub0: 1 port with 1 removable, self powered Root mount waiting for: usbus0 ugen0.2: <vendor 0x0424> at usbus0 uhub1: <vendor 0x0424 product 0x9512, class 9/0, rev 2.00/2.00, addr 2> on usbus0 uhub1: MTT enabled uhub1: 3 ports with 2 removable, self powered Root mount waiting for: usbus0 ugen0.3: <vendor 0x0424> at usbus0 smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0 Trying to mount root from ufs:/dev/mmcsd0s2a [rw,noatime]... smsc0: chip 0xec00, rev. 0002 warning: no time-of-day clock registered, system time will not be set accurately miibus0: <MII bus> on smsc0 ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto ue0: <USB Ethernet> on smsc0 ue0: Ethernet address: xx:xx:xx:xx:xx:xx smsc0: chip 0xec00, rev. 0002 pid 814 (bash), uid 0: exited on signal 6 (core dumped) pid 842 (pkg_info), uid 0: exited on signal 6 pid 845 (pkg-static), uid 0: exited on signal 12 pid 864 (pkg-static), uid 0: exited on signal 12
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?trinity-30dc2f81-d5ac-4f77-b663-116a12bfc461-1383780565220>