Date: Tue, 1 Aug 2000 20:46:27 -0500 (CDT) From: Kevin Day <toasty@dragondata.com> To: hackers@freebsd.org Subject: Lots of PCI busses confusing newbus/Compaq Proliant ML530 Message-ID: <200008020146.UAA51673@celery.dragondata.com>
next in thread | raw e-mail | index | archive | help
I've got a Compaq Proliant ML530 server that seems to work just fine with
the funky RAID controller and management software. However, the if_sk driver
is giving me a small problem. I've got a SysKonnect dual 1000Mb ethernet
card on one of the PCI busses on the motherboard. The probe gets called, but
the attach routine never seems to happen.
skc0: <SysKonnect Gigabit Ethernet> port 0x3000-0x30ff mem 0xc6afc000-0xc6afffff
irq 10 at device 6.0 on pci2
skc0: SysKonnect SK-NET Gigabit Ethernet Adapter SK-9844 SX dual link
appears but the rest doesn't. A good boot would show:
(begin of probe routine)
skc0: <SysKonnect Gigabit Ethernet> port 0xa400-0xa4ff mem 0xde000000-0xde003fff irq 11 at device 12.0 on pci0
skc0: SysKonnect SK-NET Gigabit Ethernet Adapter SK-9844 SX dual link
(begin of attach routine)
sk0: <XaQti Corp. XMAC II> on skc0
sk0: Ethernet address: 00:00:5a:98:21:6c
sk1: <XaQti Corp. XMAC II> on skc0
sk1: Ethernet address: 00:00:5a:98:21:6d
miibus1: <MII bus> on sk0
xmphy0: <XaQti Corp. XMAC II gigabit interface> on miibus1
xmphy0: 1000baseSX, 1000baseSX-FDX, auto
miibus2: <MII bus> on sk1
xmphy1: <XaQti Corp. XMAC II gigabit interface> on miibus2
xmphy1: 1000baseSX, 1000baseSX-FDX, auto
One bizarre thing appearing on boot is this:
pcib255: <RCC LE host to PCI bridge> on motherboard
pci255: <PCI bus> on pcib255
Which doesn't seem right at all.
Has anyone seen a problem like this before, or might know what I can
tune/fiddle with?
Below is my dmesg and pciconf output.
For reference there are three PCI busses on the motherboard. Bus 0 is a
32bit/33mhz bus. Bus 1 is a 64bit/33mhz bus. Bus 2 is a 64bit/66mhz bus.
Thanks,
Kevin
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #0: Tue Aug 1 11:02:42 CDT 2000
toasty@senettest.ikadega.com:/usr/src/sys/compile/NETTEST
Calibrating clock(s) ... TSC clock: 863968785 Hz, i8254 clock: 1193236 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
CPU: Pentium III/Pentium III Xeon/Celeron (863.93-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 402636800 (393200K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x003be000 - 0x17ff3fff, 398680064 bytes (97334 pages)
avail memory = 387624960 (378540K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00ffee0
bios32: Entry = 0xf0000 (c00f0000) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x84
Other BIOS signatures found:
ACPI: 000f4f90
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00091166)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00091166)
pcib0: <RCC LE host to PCI bridge> on motherboard
found-> vendor=0x1166, dev=0x0009, revid=0x06
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0009, revid=0x06
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x0e11, dev=0xa0f0, revid=0x00
class=08-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=255
map[10]: type 1, range 32, base 00001800, size 8
map[14]: type 1, range 32, base c69fff00, size 8
found-> vendor=0x1002, dev=0x4756, revid=0x7a
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base c5000000, size 24
map[14]: type 1, range 32, base 00002000, size 8
map[18]: type 1, range 32, base c69fe000, size 12
found-> vendor=0x8086, dev=0x1229, revid=0x08
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c69fd000, size 12
map[14]: type 1, range 32, base 00002400, size 6
map[18]: type 1, range 32, base c6800000, size 20
found-> vendor=0x1166, dev=0x0200, revid=0x4f
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0211, revid=0x00
class=01-01-8a, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 00002440, size 4
found-> vendor=0x1166, dev=0x0009, revid=0x06
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x1166, dev=0x0009, revid=0x06
class=06-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x0e11, dev=0xa0f0) at 3.0
pci0: <ATI Mach64-GV graphics accelerator> (vendor=0x1002, dev=0x4756) at 5.0
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x2400-0x243f mem 0xc6800000-0xc68f
ffff,0xc69fd000-0xc69fdfff irq 5 at device 8.0 on pci0
fxp0: Ethernet address 00:50:8b:ae:c5:38
bpf: fxp0 attached
isab0: <PCI to ISA bridge (vendor=1166 device=0200)> at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Generic PCI ATA controller> port 0x2440-0x244f at device 15.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x2440
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=00 status1=00
ata0: devices = 0xc
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x2448
ata1: mask=03 status0=00 status1=00
ata1: mask=03 status0=00 status1=00
ata1: devices = 0x0
ata1: probe allocation failed
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00091166)
pcib2: <RCC LE host to PCI bridge> on motherboard
found-> vendor=0x1148, dev=0x4300, revid=0x11
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
map[10]: type 1, range 32, base c6afc000, size 14
map[14]: type 1, range 32, base 00003000, size 8
pci2: <PCI bus> on pcib2
skc0: <SysKonnect Gigabit Ethernet> port 0x3000-0x30ff mem 0xc6afc000-0xc6afffff
irq 10 at device 6.0 on pci2
skc0: SysKonnect SK-NET Gigabit Ethernet Adapter SK-9844 SX dual link
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00091166)
pcib255: <RCC LE host to PCI bridge> on motherboard
pci255: <PCI bus> on pcib255
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00091166)
pcib5: <RCC LE host to PCI bridge> on motherboard
found-> vendor=0x1000, dev=0x000b, revid=0x05
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=a, irq=11
map[10]: type 1, range 32, base 00004000, size 8
map[14]: type 1, range 64, base c6bffc00, size 10
map[1c]: type 1, range 64, base c6bfc000, size 13
found-> vendor=0x1000, dev=0x000b, revid=0x05
class=01-00-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
intpin=b, irq=15
map[10]: type 1, range 32, base 00004400, size 8
map[14]: type 1, range 64, base c6bfbc00, size 10
map[1c]: type 1, range 64, base c6bf8000, size 13
found-> vendor=0x1011, dev=0x0026, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=6 secondarybus=6
found-> vendor=0x1011, dev=0x0026, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=7 secondarybus=7
pci5: <PCI bus> on pcib5
sym0: <896> port 0x4000-0x40ff mem 0xc6bfc000-0xc6bfdfff,0xc6bffc00-0xc6bfffff i
rq 11 at device 4.0 on pci5
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: handling phase mismatch from SCRIPTS.
sym1: <896> port 0x4400-0x44ff mem 0xc6bf8000-0xc6bf9fff,0xc6bfbc00-0xc6bfbfff i
rq 15 at device 4.1 on pci5
sym1: chip clock is 40401KHz
sym1: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym1: open drain IRQ line driver, using on-chip SRAM
sym1: using LOAD/STORE-based firmware.
sym1: handling phase mismatch from SCRIPTS.
pcib1: <DEC 21154 PCI-PCI bridge> at device 7.0 on pci5
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6d80000, size 19
map[14]: type 1, range 32, base 00005000, size 8
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6d00000, size 19
map[14]: type 1, range 32, base 00005400, size 8
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6c80000, size 19
map[14]: type 1, range 32, base 00005800, size 8
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6c00000, size 19
map[14]: type 1, range 32, base 00005c00, size 8
pci6: <PCI bus> on pcib1
sf0: <Adaptec ANA-62044 10/100BaseTX> port 0x5000-0x50ff mem 0xc6d80000-0xc6dfff
ff irq 5 at device 4.0 on pci6
using shared irq5.
sf0: Ethernet address: 00:00:d1:ed:c0:e5
miibus0: <MII bus> on sf0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x0005be, model 0x0003, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf0 attached
sf1: <Adaptec ANA-62044 10/100BaseTX> port 0x5400-0x54ff mem 0xc6d00000-0xc6d7ff
ff irq 5 at device 5.0 on pci6
sf1: Ethernet address: 00:00:d1:ed:c0:e6
miibus1: <MII bus> on sf1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1: OUI 0x0005be, model 0x0003, rev. 1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf1 attached
sf2: <Adaptec ANA-62044 10/100BaseTX> port 0x5800-0x58ff mem 0xc6c80000-0xc6cfff
ff irq 5 at device 6.0 on pci6
sf2: Ethernet address: 00:00:d1:ed:c0:e7
miibus2: <MII bus> on sf2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2: OUI 0x0005be, model 0x0003, rev. 1
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf2 attached
sf3: <Adaptec ANA-62044 10/100BaseTX> port 0x5c00-0x5cff mem 0xc6c00000-0xc6c7ff
ff irq 5 at device 7.0 on pci6
sf3: Ethernet address: 00:00:d1:ed:c0:e8
miibus3: <MII bus> on sf3
ukphy3: <Generic IEEE 802.3u media interface> on miibus3
ukphy3: OUI 0x0005be, model 0x0003, rev. 1
ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf3 attached
pcib3: <DEC 21154 PCI-PCI bridge> at device 9.0 on pci5
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6f80000, size 19
map[14]: type 1, range 32, base 00006000, size 8
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6f00000, size 19
map[14]: type 1, range 32, base 00006400, size 8
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6e80000, size 19
map[14]: type 1, range 32, base 00006800, size 8
found-> vendor=0x9004, dev=0x6915, revid=0x03
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=5
map[10]: type 1, range 32, base c6e00000, size 19
map[14]: type 1, range 32, base 00006c00, size 8
pci7: <PCI bus> on pcib3
sf4: <Adaptec ANA-62044 10/100BaseTX> port 0x6000-0x60ff mem 0xc6f80000-0xc6ffff
ff irq 5 at device 4.0 on pci7
sf4: Ethernet address: 00:00:d1:ed:c0:7d
miibus4: <MII bus> on sf4
ukphy4: <Generic IEEE 802.3u media interface> on miibus4
ukphy4: OUI 0x0005be, model 0x0003, rev. 1
ukphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf4 attached
sf5: <Adaptec ANA-62044 10/100BaseTX> port 0x6400-0x64ff mem 0xc6f00000-0xc6f7ff
ff irq 5 at device 5.0 on pci7
sf5: Ethernet address: 00:00:d1:ed:c0:7e
miibus5: <MII bus> on sf5
ukphy5: <Generic IEEE 802.3u media interface> on miibus5
ukphy5: OUI 0x0005be, model 0x0003, rev. 1
ukphy5: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf5 attached
sf6: <Adaptec ANA-62044 10/100BaseTX> port 0x6800-0x68ff mem 0xc6e80000-0xc6efff
ff irq 5 at device 6.0 on pci7
sf6: Ethernet address: 00:00:d1:ed:c0:7f
miibus6: <MII bus> on sf6
ukphy6: <Generic IEEE 802.3u media interface> on miibus6
ukphy6: OUI 0x0005be, model 0x0003, rev. 1
ukphy6: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf6 attached
sf7: <Adaptec ANA-62044 10/100BaseTX> port 0x6c00-0x6cff mem 0xc6e00000-0xc6e7ff
ff irq 5 at device 7.0 on pci7
sf7: Ethernet address: 00:00:d1:ed:c0:80
miibus7: <MII bus> on sf7
ukphy7: <Generic IEEE 802.3u media interface> on miibus7
ukphy7: OUI 0x0005be, model 0x0003, rev. 1
ukphy7: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
bpf: sf7 attached
eisa0: <EISA bus> on motherboard
mainboard0: <CPQ0712 (System Board)> on eisa0 slot 0
eisa0: unknown card @@@0000 (0x00000000) at slot 5
eisa0: unknown card @@@0000 (0x00000000) at slot 6
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ata3: iobase=0x0170 altiobase=0x0376 bmaddr=0x0000
ata3: mask=03 status0=00 status1=00
ata3: mask=03 status0=00 status1=00
ata3: devices = 0x0
ata3: probe allocation failed
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0065
kbdc: TEST_AUX_PORT status:0000
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: RESET_AUX return code:00fe
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: failed to reset the aux device.
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
pcic1: not probed (disabled)
sio0: irq maps: 0x8841 0x8851 0x8841 0x8841
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x8841 0x8849 0x8841 0x8841
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port found at 0x3bc
ppc0: cannot reserve I/O port range
isa_probe_children: probing PnP devices
BIOS Geometries:
0:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
1:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
2:03fffe3f 0..1023=1024 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: sl0 attached
bpf: ppp0 attached
new masks: bio 684040, tty 63001a, net 67043a
bpf: lo0 attached
bpf: gif0 attached
bpf: gif1 attached
bpf: gif2 attached
bpf: gif3 attached
bpf: faith0 attached
ata0-slave: identify retries exceeded
ata0-master: piomode=4 dmamode=2 udmamode=-1 dmaflag=1
ata0-master: success setting up PIO4 mode on generic chip
acd0: <COMPAQ CDR-8435/0013> CDROM drive at ata0 as master
acd0: read 5512KB/s (5512KB/s), 128KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA stream, packet
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
(noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
Creating DISK da0
Creating DISK da1
Creating DISK da2
pass0 at sym0 bus 0 target 0 lun 0
pass0: <COMPAQ BB01813467 3B05> Fixed Direct Access SCSI-2 device
pass0: Serial Number 3BM0F5AN0000705021C4
pass0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabl
ed
pass1 at sym0 bus 0 target 1 lun 0
pass1: <COMPAQ BB018135B5 B013> Fixed Direct Access SCSI-2 device
pass1: Serial Number 36013966 0023
pass1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabl
ed
pass2 at sym0 bus 0 target 2 lun 0
pass2: <COMPAQ BB018135B5 B013> Fixed Direct Access SCSI-2 device
pass2: Serial Number 36015080 0024
pass2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabl
ed
da0 at sym0 bus 0 target 0 lun 0
da0: <COMPAQ BB01813467 3B05> Fixed Direct Access SCSI-2 device
da0: Serial Number 3BM0F5AN0000705021C4
da0: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
da0: 17365MB (35565080 512 byte sectors: 255H 63S/T 2213C)
da1 at sym0 bus 0 target 1 lun 0
da1: <COMPAQ BB018135B5 B013> Fixed Direct Access SCSI-2 device
da1: Serial Number 36013966 0023
da1: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
da1: 17365MB (35565080 512 byte sectors: 255H 63S/T 2213C)
da2 at sym0 bus 0 target 2 lun 0
da2: <COMPAQ BB018135B5 B013> Fixed Direct Access SCSI-2 device
da2: Serial Number 36015080 0024
da2: 80.000MB/s transfers (40.000MHz, offset 31, 16bit), Tagged Queueing Enabled
da2: 17365MB (35565080 512 byte sectors: 255H 63S/T 2213C)
Mounting root from ufs:da0s1a
da0s1: type 0xa5, start 80325, end = 35551844, size 35471520 : OK
da0s3: type 0x12, start 63, end = 80324, size 80262 : OK
start_init: trying /sbin/init
splash: image decoder found: daemon_saver
# ifconfig -a
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 88.0.0.116 netmask 0xffffff00 broadcast 88.0.0.255
inet6 fe80::250:8bff:feae:c538%fxp0 prefixlen 64 scopeid 0x1
ether 00:50:8b:ae:c5:38
media: autoselect (100baseTX <full-duplex>) status: active
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP
sf0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:00:d1:ed:c0:e5
media: autoselect (none) status: no carrier
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP none
sf1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:00:d1:ed:c0:e6
media: autoselect (none) status: no carrier
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP none
sf2: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:00:d1:ed:c0:e7
media: autoselect (none) status: no carrier
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP none
sf3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:00:d1:ed:c0:e8
media: autoselect (none) status: no carrier
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP none
sf4: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:00:d1:ed:c0:7d
media: autoselect (none) status: no carrier
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP none
sf5: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:00:d1:ed:c0:7e
media: autoselect (none) status: no carrier
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP none
sf6: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:00:d1:ed:c0:7f
media: autoselect (none) status: no carrier
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP none
sf7: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:00:d1:ed:c0:80
media: autoselect (none) status: no carrier
supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP none
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0xc
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif1: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif2: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
gif3: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
faith0: flags=8000<MULTICAST> mtu 1500
# pciconf -l
chip0@pci0:0:0: class=0x060000 card=0x00000000 chip=0x00091166 rev=0x06 hdr=0x00
chip1@pci0:0:1: class=0x060000 card=0x00000000 chip=0x00091166 rev=0x06 hdr=0x00
none0@pci0:3:0: class=0x088000 card=0xb0f30e11 chip=0xa0f00e11 rev=0x00 hdr=0x00
none1@pci0:5:0: class=0x030000 card=0x47561002 chip=0x47561002 rev=0x7a hdr=0x00
fxp0@pci0:8:0: class=0x020000 card=0xb1440e11 chip=0x12298086 rev=0x08 hdr=0x00
isab0@pci0:15:0: class=0x060100 card=0x02001166 chip=0x02001166 rev=0x4f hdr=0x00
atapci0@pci0:15:1: class=0x01018a card=0x00000000 chip=0x02111166 rev=0x00 hdr=0x00
chip2@pci0:17:0: class=0x060000 card=0x00000000 chip=0x00091166 rev=0x06 hdr=0x00
chip3@pci0:17:1: class=0x060000 card=0x00000000 chip=0x00091166 rev=0x06 hdr=0x00
skc0@pci2:6:0: class=0x020000 card=0x98441148 chip=0x43001148 rev=0x11 hdr=0x00
sym0@pci5:4:0: class=0x010000 card=0x60040e11 chip=0x000b1000 rev=0x05 hdr=0x00
sym1@pci5:4:1: class=0x010000 card=0x60040e11 chip=0x000b1000 rev=0x05 hdr=0x00
pcib1@pci5:7:0: class=0x060400 card=0x000000dc chip=0x00261011 rev=0x02 hdr=0x01
pcib3@pci5:9:0: class=0x060400 card=0x000000dc chip=0x00261011 rev=0x02 hdr=0x01
sf0@pci6:4:0: class=0x020000 card=0x00199004 chip=0x69159004 rev=0x03 hdr=0x00
sf1@pci6:5:0: class=0x020000 card=0x00199004 chip=0x69159004 rev=0x03 hdr=0x00
sf2@pci6:6:0: class=0x020000 card=0x00199004 chip=0x69159004 rev=0x03 hdr=0x00
sf3@pci6:7:0: class=0x020000 card=0x00199004 chip=0x69159004 rev=0x03 hdr=0x00
sf4@pci7:4:0: class=0x020000 card=0x00199004 chip=0x69159004 rev=0x03 hdr=0x00
sf5@pci7:5:0: class=0x020000 card=0x00199004 chip=0x69159004 rev=0x03 hdr=0x00
sf6@pci7:6:0: class=0x020000 card=0x00199004 chip=0x69159004 rev=0x03 hdr=0x00
sf7@pci7:7:0: class=0x020000 card=0x00199004 chip=0x69159004 rev=0x03 hdr=0x00
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200008020146.UAA51673>