Date: Sat, 2 Dec 2006 09:46:16 +0000 From: MQ <antinvidia@gmail.com> To: "Vladimir Terziev" <vlady@gbservices.biz> Cc: Josh Paetzel <josh@tcbug.org>, freebsd-net@freebsd.org, freebsd-hackers@freebsd.org Subject: Re: FreeBSD-6.1/amd64 bge(4) driver performance problems Message-ID: <be0088ce0612020146w16aab944gfeccf5b3aab89437@mail.gmail.com> In-Reply-To: <20061129182534.5300947f.vlady@gbservices.biz> References: <20061128204732.3e8790fd.vlady@gbservices.biz> <200611290709.34059.josh@tcbug.org> <20061129182534.5300947f.vlady@gbservices.biz>
next in thread | previous in thread | raw e-mail | index | archive | help
2006/11/29, Vladimir Terziev <vlady@gbservices.biz>: > > > The cable and the switch port, both were one and the same in the > test with Broadcom NIC and in the test with D-Link NIC. So, the reason is > not in them for sure. > > I didn't mention in my initial e-mail, that since the swtich is > 100Mbps, the Broadcom NIC was forced to work on 100mbit, full-duplex. For > some reason, when using autodect, the Broadcom NIC negotiates 100mbit, > half-duplex. > > Vladimir > > On Wed, 29 Nov 2006 07:09:33 -0600 > Josh Paetzel <josh@tcbug.org> wrote: > > > On Tuesday 28 November 2006 12:47, Vladimir Terziev wrote: > > > Hi, > > > > > > i have a machine with Pentium 4-D processor utilizing > > > FreeBSD-6.1-RELEASE-p10/amd64. > > > > > > The machine is running SMP kernel. > > > > > > The machine has 2 on-board Broadcom BCM5721 NICs, which are > > > handeled by the bge(4) driver and 4 D-Link DL10050 NICs, which are > > > handeled by the ste(4) driver. Machine is targeted for a > > > gateway/firewall and will handle a big amount of network traffic. > > > > > > It seems the bge(4) driver has severe performance problems (may be > > > especially in my configuration). I tried test scp(1) to a remote > > > machine, using one of the BCM5721 NICs. The average speed which has > > > been reached was 200kBps. > > > > > > Just for comparison, when i tryed the same test scp(1), to the > > > same remote machine, but using one of the D-Link DL10050 NICs, the > > > average speed which has been reached was 10MBps. > > > > > > Could someone point me to a good performance tuning document for > > > bge(4) handeled NICs, under SMP kernel or at all? > > > > > > Thanks in advance! > > > > > > Vladimir > > > > So you have 2 gig-E and 4 100tx interfaces on the same PCI bus? If so > > you're going to run into bus saturation long before you're able to > > max out the throughput on the NICs. > > > > Which isn't to say that 200 kBps isn't a problem, but perhaps you are > > dealing with a bad cable or switchport. > > > > -- > > Thanks, > > > > Josh Paetzel > _______________________________________________ > freebsd-net@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-net > To unsubscribe, send any mail to "freebsd-net-unsubscribe@freebsd.org" > Yes, maybe the current bge(4) has some problems with the media type. When connecting a 5780 to another 5701, it completely refused to work. But when I use the 5701 to work with Intel 82547, it works great.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?be0088ce0612020146w16aab944gfeccf5b3aab89437>