Date: Tue, 28 Mar 2006 03:16:24 +0400 From: Boris Samorodov <bsam@ipt.ru> To: freebsd-acpi@FreeBSD.org Subject: Re: 6.1-PRERELEASE: freezing Message-ID: <62957879@ho.ipt.ru> In-Reply-To: <84395955@ho.ipt.ru> (Boris Samorodov's message of "Mon, 27 Mar 2006 22:30:04 %2B0400") References: <84395955@ho.ipt.ru>
next in thread | previous in thread | raw e-mail | index | archive | help
forwarding to acpi@. On Mon, 27 Mar 2006 22:30:04 +0400 Boris Samorodov wrote: > I've had 6.0-STABLE as of jan-2006. Yesterday it was upgraded to > current 6.1-PRERELEASE (tag=RELENG_6). The hardware is HP/Compaq > nx6110 notebook. > After upgrading mashine is freezing under load. After booting the > OS without any actions it's OK for two hours. But after starting of > make buildkernel the mashine freezes. > I run top on ttyv1 (make buildkernel on ttyv2). After aprox. 3-5 > minutes it freezes. I have at kernel config: > options KDB > options KDB_TRACE > options DDB > options DDB_NUMSYM > So pressing <C-A-Esc> then "c", <enter> let make buildkernel to > proceed a couple of seconds. And so on. Each command followed by > <C-A-Esc>, "c", <enter> unfreezes my notebook for awhile. "Top" shows > only two commands at RUN state: make (cc) and devd. > I launched devd -Dd. There is the result (written many times) after > unfreezing the mashine with the magic keystrokes: > ----- > Processing event '!system=ACPI subsystem=Thermal type=\_TZ_.TZ1_ notify=0x80' > Pushing table > setting system=ACPI > setting subsystem=Thermal > setting type=\_TZ_.TZ1_ Shouldn't it be TZ0? Seems that TZ1 is not used at my machine. ----- hw.acpi.supported_sleep_state: S3 S4 S5 hw.acpi.power_button_state: S5 hw.acpi.sleep_button_state: S3 hw.acpi.lid_switch_state: NONE hw.acpi.standby_state: S1 hw.acpi.suspend_state: S3 hw.acpi.sleep_delay: 1 hw.acpi.s4bios: 1 hw.acpi.verbose: 1 hw.acpi.reset_video: 1 hw.acpi.cpu.cx_supported: C1/1 C2/2 C3/38 hw.acpi.cpu.cx_lowest: C1 hw.acpi.cpu.cx_usage: 100.00% 0.00% 0.00% hw.acpi.battery.life: 100 hw.acpi.battery.time: -1 hw.acpi.battery.state: 0 hw.acpi.battery.units: 2 hw.acpi.battery.info_expire: 5 hw.acpi.acline: 1 hw.acpi.thermal.min_runtime: 0 hw.acpi.thermal.polling_rate: 10 hw.acpi.thermal.tz0.temperature: 47.0C hw.acpi.thermal.tz0.active: 3 hw.acpi.thermal.tz0.passive_cooling: 1 hw.acpi.thermal.tz0.thermal_flags: 0 hw.acpi.thermal.tz0._PSV: 100.0C hw.acpi.thermal.tz0._HOT: -1 hw.acpi.thermal.tz0._CRT: 102.0C hw.acpi.thermal.tz0._ACx: 80.0C 65.0C 55.0C 40.0C -1 -1 -1 -1 -1 -1 hw.acpi.thermal.tz1.temperature: 44.0C hw.acpi.thermal.tz1.active: -1 hw.acpi.thermal.tz1.passive_cooling: 0 hw.acpi.thermal.tz1.thermal_flags: 0 hw.acpi.thermal.tz1._PSV: -1 hw.acpi.thermal.tz1._HOT: -1 hw.acpi.thermal.tz1._CRT: 103.0C hw.acpi.thermal.tz1._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 hw.acpi.thermal.tz2.temperature: 30.2C hw.acpi.thermal.tz2.active: -1 hw.acpi.thermal.tz2.passive_cooling: 0 hw.acpi.thermal.tz2.thermal_flags: 0 hw.acpi.thermal.tz2._PSV: 60.0C hw.acpi.thermal.tz2._HOT: -1 hw.acpi.thermal.tz2._CRT: 102.0C hw.acpi.thermal.tz2._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 ----- > setting notify=0x80 > Processing notify event > Testing system=ACPI against ^ACPI > Testing subsystem=Thermal against ^ACAD > Testing system=ACPI against ^ACPI > Testing subsystem=Thermal against ^Thermal > Testing notify=0x80 against ^0xcc > Testing system=ACPI against ^IFNET > Testing system=ACPI against ^IFNET > Popping table > ----- > Booting with ACPI disabled helps as well as kernel.old with it's > modules. > /etc/make.conf: > ----- > KERNCONF?= NX6110 > X_WINDOW_SYSTEM=xorg > OVERRIDE_LINUX_BASE_PORT=fc3 > PERL_VER=5.8.7 > PERL_VERSION=5.8.7 > ----- > What type of debugging should I do to find up what's up? > Thanks. WBR -- Boris B. Samorodov, Research Engineer InPharmTech Co, http://www.ipt.ru Telephone & Internet Service Provider
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?62957879>