Skip site navigation (1)Skip section navigation (2)
Date:      Tue, 28 Mar 2006 03:16:24 +0400
From:      Boris Samorodov <bsam@ipt.ru>
To:        freebsd-acpi@FreeBSD.org
Subject:   Re: 6.1-PRERELEASE: freezing
Message-ID:  <62957879@ho.ipt.ru>
In-Reply-To: <84395955@ho.ipt.ru> (Boris Samorodov's message of "Mon, 27 Mar 2006 22:30:04 %2B0400")
References:  <84395955@ho.ipt.ru>

next in thread | previous in thread | raw e-mail | index | archive | help
forwarding to acpi@.

On Mon, 27 Mar 2006 22:30:04 +0400 Boris Samorodov wrote:

> I've had 6.0-STABLE as of jan-2006. Yesterday it was upgraded to
> current 6.1-PRERELEASE (tag=RELENG_6). The hardware is HP/Compaq
> nx6110 notebook.

> After upgrading mashine is freezing under load. After booting the
> OS without any actions it's OK for two hours. But after starting of
> make buildkernel the mashine freezes.

> I run top on ttyv1 (make buildkernel on ttyv2). After aprox. 3-5
> minutes it freezes. I have at kernel config:

> options         KDB
> options         KDB_TRACE
> options         DDB
> options         DDB_NUMSYM

> So pressing <C-A-Esc> then "c", <enter> let make buildkernel to
> proceed a couple of seconds. And so on. Each command followed by
> <C-A-Esc>, "c", <enter> unfreezes my notebook for awhile. "Top" shows
> only two commands at RUN state: make (cc) and devd.

> I launched devd -Dd. There is the result (written many times) after
> unfreezing the mashine with the magic keystrokes:
> -----
> Processing event '!system=ACPI subsystem=Thermal type=\_TZ_.TZ1_ notify=0x80'
> Pushing table
> setting system=ACPI
> setting subsystem=Thermal
> setting type=\_TZ_.TZ1_

Shouldn't it be TZ0? Seems that TZ1 is not used at my machine.
-----
hw.acpi.supported_sleep_state: S3 S4 S5
hw.acpi.power_button_state: S5
hw.acpi.sleep_button_state: S3
hw.acpi.lid_switch_state: NONE
hw.acpi.standby_state: S1
hw.acpi.suspend_state: S3
hw.acpi.sleep_delay: 1
hw.acpi.s4bios: 1
hw.acpi.verbose: 1
hw.acpi.reset_video: 1
hw.acpi.cpu.cx_supported: C1/1 C2/2 C3/38
hw.acpi.cpu.cx_lowest: C1
hw.acpi.cpu.cx_usage: 100.00% 0.00% 0.00%
hw.acpi.battery.life: 100
hw.acpi.battery.time: -1
hw.acpi.battery.state: 0
hw.acpi.battery.units: 2
hw.acpi.battery.info_expire: 5
hw.acpi.acline: 1
hw.acpi.thermal.min_runtime: 0
hw.acpi.thermal.polling_rate: 10
hw.acpi.thermal.tz0.temperature: 47.0C
hw.acpi.thermal.tz0.active: 3
hw.acpi.thermal.tz0.passive_cooling: 1
hw.acpi.thermal.tz0.thermal_flags: 0
hw.acpi.thermal.tz0._PSV: 100.0C
hw.acpi.thermal.tz0._HOT: -1
hw.acpi.thermal.tz0._CRT: 102.0C
hw.acpi.thermal.tz0._ACx: 80.0C 65.0C 55.0C 40.0C -1 -1 -1 -1 -1 -1
hw.acpi.thermal.tz1.temperature: 44.0C
hw.acpi.thermal.tz1.active: -1
hw.acpi.thermal.tz1.passive_cooling: 0
hw.acpi.thermal.tz1.thermal_flags: 0
hw.acpi.thermal.tz1._PSV: -1
hw.acpi.thermal.tz1._HOT: -1
hw.acpi.thermal.tz1._CRT: 103.0C
hw.acpi.thermal.tz1._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
hw.acpi.thermal.tz2.temperature: 30.2C
hw.acpi.thermal.tz2.active: -1
hw.acpi.thermal.tz2.passive_cooling: 0
hw.acpi.thermal.tz2.thermal_flags: 0
hw.acpi.thermal.tz2._PSV: 60.0C
hw.acpi.thermal.tz2._HOT: -1
hw.acpi.thermal.tz2._CRT: 102.0C
hw.acpi.thermal.tz2._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
-----

> setting notify=0x80
> Processing notify event
> Testing system=ACPI against ^ACPI
> Testing subsystem=Thermal against ^ACAD
> Testing system=ACPI against ^ACPI
> Testing subsystem=Thermal against ^Thermal
> Testing notify=0x80 against ^0xcc
> Testing system=ACPI against ^IFNET
> Testing system=ACPI against ^IFNET
> Popping table
> -----

> Booting with ACPI disabled helps as well as kernel.old with it's
> modules.

> /etc/make.conf:
> -----
> KERNCONF?=      NX6110
> X_WINDOW_SYSTEM=xorg
> OVERRIDE_LINUX_BASE_PORT=fc3
> PERL_VER=5.8.7
> PERL_VERSION=5.8.7
> -----

> What type of debugging should I do to find up what's up?

> Thanks.


WBR
-- 
Boris B. Samorodov, Research Engineer
InPharmTech Co,     http://www.ipt.ru
Telephone & Internet Service Provider



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?62957879>