Date: Mon, 16 Feb 1998 16:26:17 -0800 From: Amancio Hasty <hasty@rah.star-gate.com> To: Ken Krebs <schrade@schrade.com> Cc: multimedia@FreeBSD.ORG Subject: Re: Quake2 - it works! (Single and Multi!) Message-ID: <199802170026.QAA28297@rah.star-gate.com> In-Reply-To: Your message of "Mon, 16 Feb 1998 15:36:03 PST." <Pine.BSF.3.96.980216150934.18860A-100000@shell3.ba.best.com>
next in thread | previous in thread | raw e-mail | index | archive | help
[-- Attachment #1 --]
[-- Attachment #2 --]
# Configuration file for svgalib. Default location is /etc/vga.
# Lines starting with '#' are ignored.
# Have a deep look at README.config to see what can do here (especially
# for mach32).
# Mouse type:
# mouse Microsoft # Microsoft
# mouse MouseSystems # Mouse Systems
# mouse MMSeries # Logitech MM Series
# mouse Logitech # Logitech protocol (old, newer mice use Microsoft protocol)
# mouse Busmouse # Bus mouse
# mouse PS2 # PS/2 mouse
# mouse MouseMan # Logitech MouseMan
# mouse Spaceball # Spacetec Spaceball
# mouse none # None
mouse PS2
mdev /dev/psm1
# Usually /dev/mouse will be a link to the mouse device.
# However, esp. with the Spacetec Spaceball you may
# want to specify a different device for svgalib to use
# mdev /dev/ttyS0 # mouse is at /dev/ttyS0
# Some multiprotocol mice will need one of the following:
# setRTS # set the RTS wire.
# clearRTS # clear the RTS wire.
# leaveRTS # leave the RTS wire alone (default) (Wire is usually set)
# setDTR # set the DTR wire.
# clearDTR # clear the DTR wire.
# leaveDTR # leave the DTR wire alone (default) (Wire is usually set)
# Monitor type:
# Only one range can be specified for the moment. Format:
# HorizSync min_kHz max_kHz
# VertRefresh min_Hz max_Hz
# Typical Horizontal sync ranges
# (Consult your monitor manual for Vertical sync ranges)
#
# 31.5 - 31.5 kHz (Standard VGA monitor, 640x480 @ 60 Hz)
# 31.5 - 35.1 kHz (Old SVGA monitor, 800x600 @ 56 Hz)
# 31.5 - 35.5 kHz (Low-end SVGA, 8514, 1024x768 @ 43 Hz interlaced)
# 31.5 - 37.9 kHz (SVGA monitor, 800x600 @ 60 Hz, 640x480 @ 72 Hz)
# 31.5 - 48.3 kHz (SVGA non-interlaced, 800x600 @ 72 Hz, 1024x768 @ 60 Hz)
# 31.5 - 56.0 kHz (high frequency, 1024x768 @ 70 Hz)
# 31.5 - ???? kHz (1024x768 @ 72 Hz)
# 31.5 - 64.3 kHz (1280x1024 @ 60 Hz)
HorizSync 31.5 35.5
VertRefresh 50 90
# Montitor timings
#
# These are prefered over the default timings (if monitor and chipset
# can handle them). Not all drivers use them at the moment, and Mach32
# has its own syntax (see below).
# The format is identical to the one used by XFree86, but the label
# following the modeline keyword is ignored by vgalib.
#
# Here some examples:
# modeline "640x480@100" 43 640 664 824 848 480 483 490 504
# modeline "800x600@73" 50 800 856 976 1024 600 637 643 666
# modeline "1024x768@75" 85 1024 1048 1376 1400 768 771 780 806
# Mach32 timings:
# e.g. Setup a 320x200 mode for the mach32:
define 320x200x32K 320x200x64K 320x200x16M 320x200x16M32
16 320 392 464 552 200 245 265 310
# These are REQUIRED for above mode, please edit to suit your monitor.
# (No, I won't pay for a new one)
# HorizSync 29 65
# VertRefresh 42 93.5
# Chipset type:
#
# Use one of the following force chipset type.
# Autodetects if no chipset is specified.
# If a chipset driver gives trouble, try forcing VGA.
chipset VGA # Standard VGA
# chipset EGA # EGA
# chipset ET3000 # Tseng ET3000
# chipset ET4000 # Tseng ET4000
# chipset Cirrus # Cirrus Logic GD542x
# chipset TVGA # Trident TVGA8900/9000
# chipset Oak # Oak Technologies 037/067/077
# chipset S3 # S3 chipsets
# chipset GVGA6400 # Genoa 6400
# chipset ARK # ARK Logic
# chipset ATI # old ATI VGA
# chipset Mach32 # ATI Mach32
# chipset ALI # ALI2301
# chipset Mach64 # ATI Mach64
# EGA Color/mono mode:
# Required if chipset is EGA.
#
# Use one of the following digits to force color/mono:
# monotext # Card is in monochrome emulation mode
# colortext # Card is in color emulation mode
colortext
# RAMDAC support:
# Some chipsets (e.g. S3 and ARK) allows specifying a RAMDAC type.
# If your RAMDAC is not autodetected, you can try specifying it.
# Do NOT specify a RAMDAC if you card uses the S3 Trio chipset
# (the RAMDAC is built in).
# Ramdac Sierra32K
# Ramdac SC15025
# Ramdac SDAC # S3 SDAC
# Ramdac GenDAC # S3 GenDAC
# Ramdac ATT20C490 # AT&T 20C490, 491, 492 (and compatibles)
# Ramdac ATT20C498 # AT&T 20C498
# Ramdac IBMRGB52x # IBM RGB524, 526, 528 (and compatibles)
# Dotclocks:
# Some chipsets needs a list of dot clocks for optimum operation. Some
# includes or supports a programmable clock chip. You'll need to specify
# them here.
# Fixed clocks example:
# (The following is just an example, get the values for your card from
# you XF86Config)
# Clocks 25.175 28.3 40 70 50 75 36 44.9 0 118 77 31.5 110 65 72 93.5
# Programmable clockchip example:
# Clockchip ICD2061A # The only one supported right now
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199802170026.QAA28297>