Date: Thu, 19 Apr 2007 22:08:31 +0300 From: Toomas Aas <toomas.aas@raad.tartu.ee> To: MPavel@yandex.ru Cc: freebsd-questions@freebsd.org Subject: Re: Cant install freebsd6.2 on RAID1 Message-ID: <20070419220831.jr4v3qnzxco8sc00@webmail.raad.tartu.ee> In-Reply-To: <46274B42.000001.27211@colgate.yandex.ru> References: <46274B42.000001.27211@colgate.yandex.ru>
next in thread | previous in thread | raw e-mail | index | archive | help
N, 19 apr 2007 kirjutas "М. Павел" <MPavel@yandex.ru>: > Good Day. > > I▓ve got a problem: > Server: > - Motherboard Intel SE7320ep2 with integrated, simple, but fully > hardware raid controller. > - Two HDDs Seagate 200 gb combined into raid 1 (mirror). > > The HDD has 3 sections: > 3 √ not formated > 1 √ win2003 server > 2 √ keeps logic drives for windows > (there number means diskpart, not a order) > > While booting from installation CD (on device probing stage) i've > got following message: > ... > atapci0: <Intel 6300ESB UDMA100 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 31.1 on > pci0 > ata0: <ATA channel 0> on atapci0 > ata1: <ATA channel 1> on atapci0 > atapci1: <Intel 6300ESB SATA150 controller> port > 0xce80-0xce87,0xce00-0xce03,0xcd80-0xcd87,0xcd00-0xcd03,0xcc80-0xcc8f irq 18 > at device 31.2 on pci0 > ata2: <ATA channel 0> on atapci1 > ata3: <ATA channel 1> on atapci1 > ... > ad4: 188348MB <Seagate ST3300831AS 3.03> at ata2-master SATA150 > ad6: 188348MB <Seagate ST3300831AS 3.03> at ata3-master SATA150 > ar0: 188348MB <LSILogic v3 MegaRAID RAID1> status: READY > ar0: disk0 READY (master) using ad4 at ata2-master > ar0: disk1 READY (mirror) using ad6 at ata3-master > ... > > During the installation of freebsd6.2 there are 3 variants where > freebsd can be established: ad4,ad6,ar0. > I install the program to the drive ar0, make a slice on it and > install the Boot Manager in MBR. > After the installation before rebooting the system I make sure that > everything I need was copied. > > Also i checked what says atacontrol >> atacontrol status ar0 > ar0: ATA RAID 1 subdisks: ad4 ad6 status:READY > > and pciconf: >> pciconf -lv > ... > atapci0@pci0:31:1: class=0x01018a card=0x34508086 > chip=0x25a28086 rev=0x02 hdr=0x00 > vendor = 'Intel Corporation' > device = '6300ESB IDE Controller' > class = mass storage > subclass = ATA > atapci1@pci0:31:2: class=0x01048f card=0x34518086 > chip=0x25b08086 rev=0x02 hdr=0x00 > vendor = 'Intel Corporation' > device = '6300ESB Serial ATA Controller (RAID mode)' > class = mass storage > subclass = RAID > ... > > > This means that the drive is visible and freebsd defines it to be normal (?) > > Then Reboot. > > F1 - Successfully loads windows > F3 - after BTX Loader I receive the following message: "can▓t load > kerner. Reason: not found" > > lsdev says >> lsdev > disk devices: > disk0: BIOS drive A: > disk1: BIOS drive C: > >> show currdev > disk1s3a > > However while i loading from installation CD >> lsdev > disk devices: > disk0: BIOS drive A: > disk1: BIOS drive C: > disk1s3a: FFS > disk1s3b: swap > disk1s3d: FFS > disk1s3e: FFS > disk1s3f: FFS > > After that I reboot the computer and raid controller reports that > the RAID is in DEGRADED state and drives need synchronization. > _______________________________________________ > freebsd-questions@freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-questions > To unsubscribe, send any mail to "freebsd-questions-unsubscribe@freebsd.org" > -- Toomas Aas
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20070419220831.jr4v3qnzxco8sc00>