Date: Thu, 30 Jul 1998 14:38:05 -0700 (PDT) From: sky@CSUA.Berkeley.EDU (Skyler King) To: freebsd-questions@FreeBSD.ORG Subject: Internal PCI modem lossage Message-ID: <199807302138.OAA18143@soda.CSUA.Berkeley.EDU>
next in thread | raw e-mail | index | archive | help
I am having great difficulty getting FreeBSD to recognize my internal "Rockwell HCF 56K DataFax PCI modem." The last time I ran FreeBSD or NetBSD was like 5 years ago or so, so I am a little out of date as far as the intricacies of PCI cards, PnP, and what not, go. Looking at the modem config in win 98 tells me that the modem is using irq11 and i/o range 0x02f8, but that there is some special DOS compat. mode that makes it work w/ irq3 and 0x02f8. I have tried using the visual config. managaer on bootup to assign sio1 to both irq3 and irq 11 to no success. In either case it tells me that config'd irq11 is not in bitmap of probed irqs. Looking at the pci probes, it looks to me that the item listed as pci0:3 is my modem, and it reports [no driver assigned]. Does anyone have any advice for getting this modem up and running? Relevant data follows below. Should I go out and shell out for an external modem? I never remember having any problems with any of my externel modems when I ran FreeBSD. Thanks for any help sky ---------------- from dmesg: ---------------- Probing for devices on PCI bus 0: configuration mode 1 allows 32 devices. chip0 <generic PCI bridge (vendor=8086 device=7180 subclass=0)> rev 3 on pci0:0:0 mapreg[10] type=0 addr=50000000 size=4000000. chip1 <generic PCI bridge (vendor=8086 device=7181 subclass=4)> rev 3 on pci0:1:0 bridge from pci0 to pci1 through 1. mapping regs: io:22a01010 mem:41004000 pmem:0000fff0 DPT: PCI SCSI HBA Driver, version 1.4.3 pci0:3: vendor=0x127a, device=0x1003, class=comms, subclass=0x00 int a irq 11 [no driver assigned] map(10): mem32(41100000) ... sio0: irq maps: 0x1 0x11 0x1 0x1 sio0 at 0x3f8-0x3ff irq 4 on isa sio0: type 16550A sio1: configured irq 11 not in bitmap of probed irqs 0 sio1: irq maps: 0x1 0x1 0x1 0x1 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 not found at 0x2f8 sio2: disabled, not probed. sio3: disabled, not probed. ---------------- kernel config file ---------------- controller pnp0 controller isa0 controller eisa0 controller pci0 ... device sio0 at isa? port "IO_COM1" tty irq 4 vector siointr device sio1 at isa? port "IO_COM2" tty irq 11 vector siointr device sio2 at isa? disable port "IO_COM3" tty irq 5 vector siointr device sio3 at isa? disable port "IO_COM4" tty irq 9 vector siointr To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199807302138.OAA18143>