Date: Fri, 19 Jun 2015 23:09:30 +0200 From: Bernd Walter <ticso@cicely7.cicely.de> To: Adrian Chadd <adrian@freebsd.org> Cc: ticso@cicely.de, Bernd Walter <ticso@cicely7.cicely.de>, "freebsd-mips@freebsd.org" <freebsd-mips@freebsd.org> Subject: Re: TP-Link WDR-4300 - Success!!! Message-ID: <20150619210930.GD34133@cicely7.cicely.de> In-Reply-To: <20150619202622.GC34133@cicely7.cicely.de> References: <20150616162654.GB14540@cicely7.cicely.de> <20150616173105.GC14540@cicely7.cicely.de> <CAJ-Vmo=hyChuKyEqBfiV=%2BrptZhRezWydjKGj-EOzdrmseeqiQ@mail.gmail.com> <CAJ-VmonifEnh5SFvh65qUhPM6xcD=N_=H0Uhytt42wT-RQMoJw@mail.gmail.com> <20150616175831.GD14540@cicely7.cicely.de> <CAJ-VmokwAVx1VQ2%2BDjrRb86Fkuf-K8%2B3jChS=LoCu7C=h=vxRg@mail.gmail.com> <20150619202622.GC34133@cicely7.cicely.de>
next in thread | previous in thread | raw e-mail | index | archive | help
On Fri, Jun 19, 2015 at 10:26:22PM +0200, Bernd Walter wrote:
> On Tue, Jun 16, 2015 at 12:10:13PM -0700, Adrian Chadd wrote:
> > Ok, right. I nthat case it's just 2x2 wifi, and gige ethernet.
> >
> > the config string to put in the build cfg file, fro mopenwrt:
> >
> > $(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWDR3600V1,tl-wdr3600-v1,TL-WDR4300,ttyS0,115200,0x36000001,1,8Mlzma))
> > $(eval $(call SingleProfile,TPLINK-LZMA,64kraw,TLWDR4300V1,tl-wdr4300-v1,TL-WDR4300,ttyS0,115200,0x43000001,1,8Mlzma))
>
> So if I got it right, then all I need to change is the TPLINK_HARDWARE_ID
> from 0x36000001 to 0x43000001, right?
>
> > .. same kernel config should work fine. I'll go update
> > freebsd-wifi-build tonight once I wrap up with work.
>
> git pull didn't show up anything new.
> Nevertheless I'm building with the mentioned change right now.
It's booting :-)
Next step will be trying to populate an USB-Stick with a
full base root-fs.
Will take some time because of this UFS-byteorder thing
If anyone has a tip to do using an ARM or i386.
Last time I did a NFS-root carambola 2 and copy'ed from
NFS to local stick using this board.
U-Boot 1.1.4 (Jun 17 2013 - 12:31:57)
U-boot DB120
DRAM: 128 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment
PCIe Reset OK!!!!!!
In: serial
Out: serial
Err: serial
Net: ag934x_enet_initialize...
No valid address in Flash. Using fixed address
wasp reset mask:c03300
WASP ----> S17 PHY *
: cfg1 0x7 cfg2 0x7114
eth0: ba:be:fa:ce:08:41
athrs17_reg_init: complete
eth0 up
eth0
Autobooting in 1 seconds
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
CPU platform: Atheros AR9344 rev 2
CPU Frequency=560 MHz
CPU DDR Frequency=450 MHz
CPU AHB Frequency=225 MHz
platform frequency: 560 MHz
CPU reference clock: 40 MHz
CPU MDIO clock: 100 MHz
arguments:
a0 = 00000007
a1 = a7f8ffb0
a2 = 08000000
a3 = 00000008
Cmd line:argv is invalid
Environment:
envp is invalid
Cache info:
picache_stride = 4096
picache_loopcount = 16
pdcache_stride = 4096
pdcache_loopcount = 8
cpu0: MIPS Technologies processor v76.151
MMU: Standard TLB, 32 entries
L1 i-cache: 4 ways of 512 sets, 32 bytes per line
L1 d-cache: 4 ways of 256 sets, 32 bytes per line
Config1=0xbee3519e<PerfCount,WatchRegs,MIPS16,EJTAG>
Config3=0x2c20
Physical memory chunk(s):
0x545000 - 0x7ffffff, 128692224 bytes (31419 pages)
Maxmem is 0x8000000
ar934x_chip_init_gmac: gmac_cfg=0x00000001
ar934x_configure_gmac: ETH_CFG=0x00000001
ar71xx: Overriding MAC from EEPROM
ar71xx: Board MAC: 14:cc:20:ed:1c:7b
ar71xx: devid 'ath.0', MAC offset '0'
hint.ath.0.macaddr => 14:cc:20:ed:1c:7b
ar71xx: devid 'ath.1', MAC offset '-1'
hint.ath.1.macaddr => 14:cc:20:ed:1c:7a
ar71xx: devid 'arge.0', MAC offset '-2'
hint.arge.0.macaddr => 14:cc:20:ed:1c:79
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2015 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #0 r284544: Fri Jun 19 22:48:59 CEST 2015
ticso@cicely1.cicely.de:/home/builder/wdr4300/obj/mips/mips.mips/home/builder/wdr4300/head/sys/TL-WDR4300 mips
gcc version 4.2.1 20070831 patched [FreeBSD]
Preloaded elf kernel "kernel" at 0x8053e7c0.
real memory = 134217728 (131072K bytes)
Physical memory chunk(s):
0x005d9000 - 0x07d98fff, 125566976 bytes (30656 pages)
avail memory = 125296640 (119MB)
wlan: <802.11 Link Layer>
random: entropy device infrastructure driver
random: selecting highest priority adaptor <Dummy>
mem: <memory>
null: <full device, null device, zero device>
random: SOFT: yarrow init()
random: selecting highest priority adaptor <Yarrow>
nexus0: <MIPS32 root nexus>
clock0: <Generic MIPS32 ticker> on nexus0
Timecounter "MIPS32" frequency 280000000 Hz quality 800
Event timer "MIPS32" frequency 280000000 Hz quality 800
argemdio0: <Atheros AR71xx built-in ethernet interface, MDIO controller> at mem 0x19000000-0x19000fff on nexus0
mdio0: <MDIO> on argemdio0
mdioproxy0: <MII/MDIO proxy, MDIO side> on mdio0
arswitch0: <Atheros AR8327 Ethernet Switch (ver 1 rev 4)> on mdio0
arswitch0: ar8327_fetch_pdata_port: port 0: speed=3, duplex=1, txpause=1, rxpause=1
arswitch0: ar8327_fetch_pdata_pad: pad 0: mode=6, rxclk_sel=0, txclk_sel=0, txclk_delay_sel=1, rxclk_delay_sel=2, txclk_delay_en=1,
rxclk_enable_en=1, sgmii_delay_en=0, pipe_rxclk_sel=0
arswitch0: ar8327_phy_fixup: called; phy=0; chiprev=4
arswitch0: ar8327_phy_fixup: called; phy=1; chiprev=4
arswitch0: ar8327_phy_fixup: called; phy=2; chiprev=4
arswitch0: ar8327_phy_fixup: called; phy=3; chiprev=4
arswitch0: ar8327_phy_fixup: called; phy=4; chiprev=4
miibus0: <MII bus> on arswitch0
ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0
ukphy0: OUI 0x00c82e, model 0x0003, rev. 4
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus1: <MII bus> on arswitch0
ukphy1: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy1: OUI 0x00c82e, model 0x0003, rev. 4
ukphy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus2: <MII bus> on arswitch0
ukphy2: <Generic IEEE 802.3u media interface> PHY 2 on miibus2
ukphy2: OUI 0x00c82e, model 0x0003, rev. 4
ukphy2: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus3: <MII bus> on arswitch0
ukphy3: <Generic IEEE 802.3u media interface> PHY 3 on miibus3
ukphy3: OUI 0x00c82e, model 0x0003, rev. 4
ukphy3: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus4: <MII bus> on arswitch0
ukphy4: <Generic IEEE 802.3u media interface> PHY 4 on miibus4
ukphy4: OUI 0x00c82e, model 0x0003, rev. 4
ukphy4: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
etherswitch0: <Switch controller> on arswitch0
mdio1: <MDIO> on arswitch0
mdioproxy1: <MII/MDIO proxy, MDIO side> on mdio1
argemdio1: <Atheros AR71xx built-in ethernet interface, MDIO controller> at mem 0x1a000000-0x1a000fff on nexus0
mdio2: <MDIO> on argemdio1
mdioproxy2: <MII/MDIO proxy, MDIO side> on mdio2
arswitch1: <Atheros AR9340 Ethernet Switch (ver 0 rev 0)> on mdio2
arswitch1: ar9340_hw_global_setup: GMII
arswitch1: ar9340_hw_global_setup: PHY4 - Local
miibus5: <MII bus> on arswitch1
ukphy5: <Generic IEEE 802.3u media interface> PHY 0 on miibus5
ukphy5: OUI 0x00c82e, model 0x0004, rev. 2
ukphy5: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus6: <MII bus> on arswitch1
ukphy6: <Generic IEEE 802.3u media interface> PHY 1 on miibus6
ukphy6: OUI 0x00c82e, model 0x0004, rev. 2
ukphy6: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus7: <MII bus> on arswitch1
ukphy7: <Generic IEEE 802.3u media interface> PHY 2 on miibus7
ukphy7: OUI 0x00c82e, model 0x0004, rev. 2
ukphy7: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus8: <MII bus> on arswitch1
ukphy8: <Generic IEEE 802.3u media interface> PHY 3 on miibus8
ukphy8: OUI 0x00c82e, model 0x0004, rev. 2
ukphy8: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
miibus9: <MII bus> on arswitch1
ukphy9: <Generic IEEE 802.3u media interface> PHY 4 on miibus9
ukphy9: OUI 0x00c82e, model 0x0004, rev. 2
ukphy9: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT-FDX, 1000baseT-FDX-master, auto
etherswitch1: <Switch controller> on arswitch1
mdio3: <MDIO> on arswitch1
mdioproxy3: <MII/MDIO proxy, MDIO side> on mdio3
apb0 at irq 4 on nexus0
uart0: <16550 or compatible> at mem 0x18020003-0x1802001a irq 3 on apb0
uart0: console (115200,n,8,1)
uart0: fast interrupt
gpio0: <Atheros AR71XX GPIO driver> at mem 0x18040000-0x18040fff irq 2 on apb0
gpio0: [GIANT-LOCKED]
gpio0: gpio pinmask=0x63f800
gpio0: ar71xx_gpio_attach: GPIO 18: func=46, mode=1
gpio0: ar71xx_gpio_attach: GPIO 19: func=47, mode=1
gpiobus0: <GPIO bus> on gpio0
gpioled0: <GPIO led> at pin(s) 11 on gpiobus0
gpioled1: <GPIO led> at pin(s) 12 on gpiobus0
gpioled2: <GPIO led> at pin(s) 13 on gpiobus0
gpioled3: <GPIO led> at pin(s) 14 on gpiobus0
gpioled4: <GPIO led> at pin(s) 15 on gpiobus0
gpioc0: <GPIO controller> on gpio0
ehci0: <AR71XX Integrated USB 2.0 controller> at mem 0x1b000100-0x1b0010ff irq 1 on nexus0
usbus0: set host controller mode
usbus0: EHCI version 1.0
usbus0: set host controller mode
usbus0 on ehci0
ehci0: usbpf: Attached
pcib0 at irq 0 on nexus0
pcib0: ar724x_pci_slot_fixup: checking dev pcib0, 0/0/0
pcib0: found EEPROM at 0x1fff4000 on 0.0.0
pcib0: EEPROM firmware: 0x1fff4000 @ 16384 bytes
firmware: 'pcib.0.bus.0.0.0.eeprom_firmware' version 1: 16384 bytes loaded at 0xc0861000
pcib0: device EEPROM 'pcib.0.bus.0.0.0.eeprom_firmware' registered
pci0: <PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x168c, dev=0x0033, revid=0x01
domain=0, bus=0, slot=0, func=0
class=02-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0146, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 3 supports D0 D1 D3 current D0
MSI supports 4 messages, 64 bit, vector masks
map[10]: type Memory, range 64, base 0, size 17, enabled
ath1: <Atheros AR9580> at device 0.0 on pci0
ath1: Lazy allocation of 0x20000 bytes rid 0x10 type 3 at 0x10000000
ath1: ath_pci_attach: looking up firmware @ 'pcib.0.bus.0.0.0.eeprom_firmware'
ath1: ath_pci_attach: EEPROM firmware @ 0xc0861000
ar9300_attach: calling ar9300_hw_attach
ar9300_hw_attach: calling ar9300_eeprom_attach
ar9300_flash_map: unimplemented for now
Restoring Cal data from DRAM
ar9300_hw_attach: ar9300_eeprom_attach returned 0
ath1: RX status length: 48
ath1: RX buffer size: 4096
ath1: TX descriptor length: 128
ath1: TX status length: 36
ath1: TX buffers per descriptor: 4
ath1: ath_edma_setup_rxfifo: type=0, FIFO depth = 16 entries
ath1: ath_edma_setup_rxfifo: type=1, FIFO depth = 128 entries
ath1: [HT] enabling HT modes
ath1: [HT] enabling short-GI in 20MHz mode
ath1: [HT] 1 stream STBC receive enabled
ath1: [HT] 1 stream STBC transmit enabled
ath1: [HT] 3 RX streams; 3 TX streams
ath1: Overriding MAC address from environment: '14:cc:20:ed:1c:7a'
ath1: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath1: 3T3R
ath1: 11na MCS 20MHz
ath1: MCS 0-7: 6.5Mbps - 65Mbps
ath1: MCS 8-15: 13Mbps - 130Mbps
ath1: MCS 16-23: 19.5Mbps - 195Mbps
ath1: 11na MCS 20MHz SGI
ath1: MCS 0-7: 7Mbps - 72Mbps
ath1: MCS 8-15: 14.5Mbps - 144.5Mbps
ath1: MCS 16-23: 21.5Mbps - 216.5Mbps
ath1: 11na MCS 40MHz:
ath1: MCS 0-7: 13.5Mbps - 135Mbps
ath1: MCS 8-15: 27Mbps - 270Mbps
ath1: MCS 16-23: 40.5Mbps - 405Mbps
ath1: 11na MCS 40MHz SGI:
ath1: MCS 0-7: 15Mbps - 150Mbps
ath1: MCS 8-15: 30Mbps - 300Mbps
ath1: MCS 16-23: 45Mbps - 450Mbps
ath1: AR9580 mac 448.4 RF5110 phy 361.6
ath1: 2GHz radio: 0x0000; 5GHz radio: 0x0000
ath1: Use hw queue 1 for WME_AC_BE traffic
ath1: Use hw queue 0 for WME_AC_BK traffic
ath1: Use hw queue 2 for WME_AC_VI traffic
ath1: Use hw queue 3 for WME_AC_VO traffic
ath1: Use hw queue 8 for CAB traffic
ath1: Use hw queue 9 for beacons
ath1: using multicast key search
arge0: <Atheros AR71xx built-in ethernet interface> at mem 0x19000000-0x19000fff irq 2 on nexus0
arge0: Overriding MAC address from environment: '14:cc:20:ed:1c:79'
arge0: arge_fetch_pll_config: pll_1000 = 0x6000000
arge0: arge_attach: overriding MII mode to 'RGMII'
mii_attach_proxy: not attaching, no mdio device hint for arge0
arge0: finishing attachment, phymask 0000, proxy null
arge0: bpf attached
arge0: Ethernet address: 14:cc:20:ed:1c:79
arge1: <Atheros AR71xx built-in ethernet interface> at mem 0x1a000000-0x1a000fff irq 3 on nexus0
arge1: arge_attach: overriding MII mode to 'GMII'
arge1: Generating random ethernet address.
mii_attach_proxy: not attaching, no mdio device hint for arge1
arge1: finishing attachment, phymask 0000, proxy null
arge1: bpf attached
arge1: Ethernet address: 62:73:64:c6:e0:10
ath0: Vendor=0x168c, Device=0x0031
ath0: Vendor=0x168c, Device=0x0031
ath0: <Atheros AR934x> at mem 0x18100000-0x1811ffff irq 0 on nexus0
ath0: eeprom @ 0x1fff0000 (16384 bytes)
ath0: eeprom data @ 0xbfff0000
Bootstrap clock 40MHz
Enterprise mode: 0x00000000
ar9300_attach: calling ar9300_hw_attach
ar9300_hw_attach: calling ar9300_eeprom_attach
ar9300_flash_map: unimplemented for now
Restoring Cal data from DRAM
ar9300_hw_attach: ar9300_eeprom_attach returned 0
ath0: RX status length: 48
ath0: RX buffer size: 4096
ath0: TX descriptor length: 128
ath0: TX status length: 36
ath0: TX buffers per descriptor: 4
ath0: ath_edma_setup_rxfifo: type=0, FIFO depth = 16 entries
ath0: ath_edma_setup_rxfifo: type=1, FIFO depth = 128 entries
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 stream STBC transmit enabled
ath0: [HT] 2 RX streams; 2 TX streams
ath0: Overriding MAC address from environment: '14:cc:20:ed:1c:7b'
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: 2T2R
ath0: 11ng MCS 20MHz
ath0: MCS 0-7: 6.5Mbps - 65Mbps
ath0: MCS 8-15: 13Mbps - 130Mbps
ath0: 11ng MCS 20MHz SGI
ath0: MCS 0-7: 7Mbps - 72Mbps
ath0: MCS 8-15: 14.5Mbps - 144.5Mbps
ath0: 11ng MCS 40MHz:
ath0: MCS 0-7: 13.5Mbps - 135Mbps
ath0: MCS 8-15: 27Mbps - 270Mbps
ath0: 11ng MCS 40MHz SGI:
ath0: MCS 0-7: 15Mbps - 150Mbps
ath0: MCS 8-15: 30Mbps - 300Mbps
ath0: AR9340 mac 768.2 RF5110 phy 850.9
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
ath0: Use hw queue 1 for WME_AC_BE traffic
ath0: Use hw queue 0 for WME_AC_BK traffic
ath0: Use hw queue 2 for WME_AC_VI traffic
ath0: Use hw queue 3 for WME_AC_VO traffic
ath0: Use hw queue 8 for CAB traffic
ath0: Use hw queue 9 for beacons
ath0: using multicast key search
spi0: <AR71XX SPI> at mem 0x1f000000-0x1f00000f on nexus0
spibus0: <spibus bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 on spibus0
mx25l0: w25q64, sector 65536 bytes, 128 sectors
ar71xx_wdog0: <Atheros AR71XX watchdog timer> on nexus0
Device configuration finished.
Timecounters tick every 1.000 msec
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 2048
lo0: bpf attached
arswitch0port1: link state changed to DOWN
arswitch0port2: link state changed to DOWN
arswitch0port3: link state changed to DOWN
arswitch0port4: link state changed to DOWN
arswitch0port5: link state changed to DOWN
arswitch1port1: link state changed to DOWN
arswitch1port2: link state changed to DOWN
arswitch1port3: link state changed to DOWN
arswitch1port4: link state changed to DOWN
arswitch1port5: link state changed to DOWN
GEOM: new disk flash/spi0
usbus0: 480Mbps High Speed USB v2.0
MAP: flash/spi0: 0x20000, data=0x20000 "/dev/map/u-boot"
MAP: search flash/spi0 for key ".!/bin/sh" from 0x20000, step 0x10000
ugen0.1: <Atheros> at usbus0
uhub0: <Atheros EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
MAP: flash/spi0: 20000x160000, data=0x160000 "/dev/map/kernel"
MAP: search flash/spi0 for key ".!/bin/sh" from 0x20000, step 0x10000
MAP: flash/spi0: 180000x650000, data=0x650000 "/dev/map/rootfs"
MAP: flash/spi0: 7d0000x10000, data=0x10000 "/dev/map/cfg"
MAP: flash/spi0: 7e0000x10000, data=0x10000 "/dev/map/mib0"
MAP: flash/spi0: 7f0000x10000, data=0x10000 "/dev/map/ART"
map/rootfs.uncompress: GEOM_ULZMA image found
map/rootfs.uncompress: 276 x 65536 blocks
MAP: No valid partition found at map/rootfs.uncompress
random: unblocking device.
Root mount waiting for: usbus0
uhub0: 1 port with 1 removable, self powered
arswitch0: arswitch_miipollstat: port 4: port -> UP
arswitch0port5: link state changed to UP
ugen0.2: <vendor 0x05e3> at usbus0
uhub1: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/85.36, addr 2> on usbus0
Root mount waiting for: usbus0
uhub1: 4 ports with 4 removable, self powered
Trying to mount root from ufs:map/rootfs.uncompress []...
warning: no time-of-day clock registered, system time will not be set accurately
start_init: trying /sbin/init
Jun 19 20:49:54 init: login_getclass: unknown class 'daemon'
MAP: No valid partition found at md0
MAP: No valid partition found at md0
MAP: No valid partition found at md1
MAP: No valid partition found at md1
MAP: No valid partition found at md2
MAP: No valid partition found at md2
*** Populating /var ..
*** Loading configuration files ..
*** Restoring from /dev/map/cfg ..
gunzip: unknown compression format
1+0 records in
1+0 records out
65536 bytes transferred in 3.963786 secs (16534 bytes/sec)
0 blocks
*** Completed.
*** setting up hostname
*** Load kernel modules
.. bridgestp
kldload: can't load bridgestp: module already loaded or in kernel
.. if_bridge
kldload: can't load if_bridge: No such file or directory
.. random
kldload: can't load random: No such file or directory
*** bringing up loopback ..
*** Default password/login databases ..
*** Starting networking via /etc/rc.d/base/net
*** Interface: arge0: start
*** Interface: arge0: done
*** Interface: bridge0: start
bridge0: bpf attached
bridge0: Ethernet address: ee:30:74:00:5a:28
arge0: promiscuous mode enabled
bridge0: link state changed to UP
*** Interface: bridge0: done
*** inetd
*** Done!
FreeBSD/mips (freebsd-wifi) (ttyu0)
login:
--
B.Walter <bernd@bwct.de> http://www.bwct.de
Modbus/TCP Ethernet I/O Baugruppen, ARM basierte FreeBSD Rechner uvm.
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20150619210930.GD34133>