From owner-freebsd-questions Sun Apr 7 13: 6:30 2002 Delivered-To: freebsd-questions@freebsd.org Received: from web9205.mail.yahoo.com (web9205.mail.yahoo.com [216.136.129.38]) by hub.freebsd.org (Postfix) with SMTP id C5FBB37B405 for ; Sun, 7 Apr 2002 13:06:23 -0700 (PDT) Message-ID: <20020407200623.76631.qmail@web9205.mail.yahoo.com> Received: from [67.241.164.218] by web9205.mail.yahoo.com via HTTP; Sun, 07 Apr 2002 13:06:23 PDT Date: Sun, 7 Apr 2002 13:06:23 -0700 (PDT) From: William Gnadt Reply-To: wgnadt@rri-usa.org Subject: help with USB hard drive To: freebsd-questions@freebsd.org Cc: wgnadt@rri-usa.org MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk List-ID: List-Archive: (Web Archive) List-Help: (List Instructions) List-Subscribe: List-Unsubscribe: X-Loop: FreeBSD.ORG Hi: I've recently acquired a USB (1.1) hard disk enclosure. I can use it successfully under Windows AFTER installing the supllied drivers. However, it's unclear how (or if) I can mount this drive under FreeBSD. Below is the output from my /var/run/dmesg.boot. The ATAPI-4 bridge is listed as device 'ugen0'. Is it possible to talk to the bridge? If so, how can I mount the HD? Thanks for any help or pointers. (My web searches turned up very little on the subject.) --Bill Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.5-STABLE #0: Thu Feb 21 10:04:48 EST 2002 wgnadt@merlin.local.net:/usr/src/sys/compile/MYKERNEL Timecounter "i8254" frequency 1193182 Hz CPU: AMD-K6(tm) 3D processor (400.91-MHz 586-class CPU) Origin = "AuthenticAMD" Id = 0x58c Stepping = 12 Features=0x8021bf AMD Features=0x80000800 real memory = 268369920 (262080K bytes) avail memory = 256061440 (250060K bytes) Preloaded elf kernel "kernel" at 0xc04f5000. K6-family MTRR support enabled (2 registers) md0: Malloc disk Using $PIR table, 6 entries at 0xc00fdd10 npx0: on motherboard npx0: INT 16 interface pcib0: on motherboard pci0: on pcib0 pcib1: at device 1.0 on pci0 pci1: on pcib1 pci1: at 0.0 irq 11 isab0: at device 7.0 on pci0 isa0: on isab0 atapci0: port 0xb400-0xb40f at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 uhci0: port 0xb000-0xb01f irq 11 at device 7.2 on pci0 usb0: on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ugen0: Prolific Technology Inc. ATAPI-4 Bridge Controller, rev 1.00/1.00, addr 2pcib2: at device 7.3 on pci0 atapci1: port 0xc800-0xc83f,0xc400-0xc403,0xc000-0xc007,0xbc00-0xbc03,0xb800-0xb807 mem 0xe9000000-0xe901ffff irq 11 at device 9.0 on pci0 ata2: at 0xb800 on atapci1 ata3: at 0xc000 on atapci1 pcm0: port 0xcc00-0xcc3f irq 11 at device 10.0 on pci0 orm0: