Date: Thu, 3 Apr 2003 13:03:09 -0500 From: Jason Cribbins <freebsd@kibserv.org> To: questions@freebsd.org Subject: Install SCSI CD-R Message-ID: <200304031303.09427.freebsd@kibserv.org>
next in thread | raw e-mail | index | archive | help
I have had no luck at all finding the correct procedure to install a SCSI=
CD-R=20
under FreeBSD. I am uses an AHA-1701 SCSI controller but I believe this =
is=20
not being seen at all by the hardware probe...although I may not even kno=
w=20
what I am looking for.
I Am running FreeBSD 5.0-RELEASAE installed from the FTP site about 2 mon=
ths=20
ago so everything is pretty recent versions of everything. The only reas=
on I=20
am runing 5.0-RELEASE is because it seems to be the only one that support=
s my=20
SB Live sound card.
Anyhow below is the dmesg.today. Anyone see if my card is even being=20
reconized by FreeBSD...and if not is there an driver I can load before th=
e=20
kernel boots much like then one I use for my sb live?
THanks
Jason Cribbins
12:53pm butters:/var/log # cat dmesg.today
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE #0: Thu Jan 16 22:16:53 GMT 2003
root@hollin.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc064e000.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc064e0a8.
Preloaded elf module "/boot/kernel/snd_emu10k1.ko" at 0xc064e154.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 451024572 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (451.02-MHz 686-class CPU)
Origin =3D "GenuineIntel" Id =3D 0x673 Stepping =3D 3
=20
Features=3D0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,=
CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory =3D 268435456 (256 MB)
avail memory =3D 252944384 (241 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using $PIR table, 8 entries at 0xc00fded0
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherb=
oard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe8000000-0xebffff=
ff at=20
device 0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 2.1 =
on=20
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd000-0xd01f irq 1=
1 at=20
device 2.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Cypress Sem PS2/USB Browser Combo Mouse, rev 1.00/0.10, addr 2, icl=
ass=20
3/1
ums0: 5 buttons and Z dir.
pci0: <bridge, PCI-unknown> at device 2.3 (no driver attached)
pci0: <display, VGA> at device 13.0 (no driver attached)
dc0: <82c169 PNIC 10/100BaseTX> port 0xd800-0xd8ff mem 0xee010000-0xee010=
0ff=20
irq 12 at device 15.0 on pci0
dc0: Ethernet address: 00:a0:cc:28:41:fa
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcm0: <Creative EMU10K1> port 0xdc00-0xdc1f irq 11 at device 16.0 on pci0
orm0: <Option ROMs> at iomem 0xcc000-0xcdfff,0xc0000-0xc8fff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port=20
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <OKI DATA CORP OKIPAGE 10e> PJL,PCLXL,PCL,EPSONFX,IBMPPR
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0a03> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
Timecounters tick every 10.000 msec
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: 19541MB <Maxtor 2B020H1> [39703/16/63] at ata0-master UDMA33
acd0: CDROM <ATAPI CDROM> at ata0-slave PIO4
Mounting root from ufs:/dev/ad0s1a
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE #0: Thu Jan 16 22:16:53 GMT 2003
root@hollin.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc064e000.
Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc064e0a8.
Preloaded elf module "/boot/kernel/snd_emu10k1.ko" at 0xc064e154.
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 451024572 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (451.02-MHz 686-class CPU)
Origin =3D "GenuineIntel" Id =3D 0x673 Stepping =3D 3
=20
Features=3D0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,=
CMOV,PAT,PSE36,PN,MMX,FXSR,SSE>
real memory =3D 268435456 (256 MB)
avail memory =3D 252944384 (241 MB)
Initializing GEOMetry subsystem
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
Using $PIR table, 8 entries at 0xc00fded0
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> at pcibus 0 on motherb=
oard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe8000000-0xebffff=
ff at=20
device 0.0 on pci0
pcib1: <PCIBIOS PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xf000-0xf00f at device 2.1 =
on=20
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xd000-0xd01f irq 1=
1 at=20
device 2.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ums0: Cypress Sem PS2/USB Browser Combo Mouse, rev 1.00/0.10, addr 2, icl=
ass=20
3/1
ums0: 5 buttons and Z dir.
pci0: <bridge, PCI-unknown> at device 2.3 (no driver attached)
pci0: <display, VGA> at device 13.0 (no driver attached)
dc0: <82c169 PNIC 10/100BaseTX> port 0xd800-0xd8ff mem 0xee010000-0xee010=
0ff=20
irq 12 at device 15.0 on pci0
dc0: Ethernet address: 00:a0:cc:28:41:fa
miibus0: <MII bus> on dc0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcm0: <Creative EMU10K1> port 0xdc00-0xdc1f irq 11 at device 16.0 on pci0
orm0: <Option ROMs> at iomem 0xcc000-0xcdfff,0xc0000-0xc8fff on isa0
pmtimer0 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port=20
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <OKI DATA CORP OKIPAGE 10e> PJL,PCLXL,PCL,EPSONFX,IBMPPR
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=3D0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0c02> can't assign resources (memory)
unknown: <PNP0a03> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0400> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
Timecounters tick every 10.000 msec
ad0: DMA limited to UDMA33, non-ATA66 cable or device
ad0: 19541MB <Maxtor 2B020H1> [39703/16/63] at ata0-master UDMA33
acd0: CDROM <ATAPI CDROM> at ata0-slave PIO4
Mounting root from ufs:/dev/ad0s1a
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
dc0: failed to force tx and rx to idle state
12:53pm butters:/var/log #
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200304031303.09427.freebsd>