Date: Wed, 11 Dec 2002 15:09:14 +0100 From: "Paul A. Mayer" <paul@fnug.net> To: hackers@freebsd.org Subject: Crash with 5.0-RC1 Message-ID: <3DF7470A.2060904@fnug.net>
next in thread | raw e-mail | index | archive | help
Greetings, I understand that this is the place to send debugging dumps from kernel crashes. If I'm misinformed, please advise. The original problem is described here and other thread contributor indicates a similar problem on similar hardware: http://marc.theaimsgroup.com/?l=freebsd-current&m=103954227212045&w=2 There is another person with an acpi crash problem here: http://marc.theaimsgroup.com/?l=freebsd-current&m=103955920101157&w=2 The gdb output from "where" is below. Please let me know what I can do to help. The configuration ran without a hitch under DP2. /Paul -bash-2.05b$ gdb -k kernel.debug.0 vmcore.1 GNU gdb 5.2.1 (FreeBSD) Copyright 2002 Free Software Foundation, Inc. GDB is free software, covered by the GNU General Public License, and you are welcome to change it and/or distribute copies of it under certain conditions. Type "show copying" to see the conditions. There is absolutely no warranty for GDB. Type "show warranty" for details. This GDB was configured as "i386-undermydesk-freebsd"... panic: from debugger panic messages: --- Fatal trap 12: page fault while in kernel mode fault virtual address = 0x42 fault code = supervisor read, page not present instruction pointer = 0x8:0xc042c517 stack pointer = 0x10:0xdf0caa04 frame pointer = 0x10:0xdf0caa1c code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 6 (acpi_task1) panic: from debugger Fatal trap 3: breakpoint instruction fault while in kernel mode instruction pointer = 0x8:0xc045c4f4 stack pointer = 0x10:0xdf0ca784 frame pointer = 0x10:0xdf0ca790 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = IOPL = 0 current process = 6 (acpi_task1) panic: from debugger Uptime: 31s Dumping 1023 MB ata0: resetting devices .. done 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320 336 352 368 384 400 416 432 448 464 480 496 512 528 544 560 576 592 608 624 640 656 672 688 704 720 736 752 768 784 800 816 832 848 864 880 896 912 928 944 960 976 992 1008Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-RC1 #0: Sat Dec 7 22:16:29 GMT 2002 root@freebsd-current.sentex.ca:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc06b5000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06b50a8. Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 1200049432 Hz CPU: Pentium 4 (1200.05-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 Features=0xffffffffbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,<b31>> real memory = 1073713152 (1023 MB) avail memory = 1036169216 (988 MB) Initializing GEOMetry subsystem Pentium Pro MTRR support enabled npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <ASUS P4_L3CS > on motherboard ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15 ACPI-0625: *** Info: GPE Block1 defined as GPE16 to GPE31 Using $PIR table, 6 entries at 0xc00f13b0 acpi0: power button is handled as a fixed feature programming model. Timecounter "ACPI-fast" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_tz0: <thermal zone> on acpi0 acpi_button0: <Sleep Button> on acpi0 acpi_acad0: <AC adapter> on acpi0 acpi_cmbat0: <Control method Battery> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xefffffff at device 0.0 on pci0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xb800-0xb81f irq 5 at device 29.0 on pci0 usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0xb400-0xb41f irq 9 at device 29.1 on pci0 usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib2 rl0: <RealTek 8139 10/100BaseTX> port 0xa800-0xa8ff mem 0xd6800000-0xd68000ff irq 9 at device 5.0 on pci2 rl0: Realtek 8139B detected. Warning, this may be unstable in autoselect mode rl0: Ethernet address: 00:e0:18:bc:f6:85 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto cbb0: <RF5C476 PCI-CardBus Bridge> irq 5 at device 7.0 on pci2 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb1: <RF5C476 PCI-CardBus Bridge> irq 11 at device 7.1 on pci2 cardbus1: <CardBus bus> on cbb1 pccard1: <16-bit PCCard bus> on cbb1 pci2: <serial bus, FireWire> at device 7.2 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH3 ATA100 controller> port 0x8400-0x840f,0x8800-0x8803,0x9000-0x9007,0x9400-0x9403,0x9800-0x9807 mem 0xd5800000-0xd58003ff irq 9 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <multimedia, audio> at device 31.5 (no driver attached) pci0: <simple comms> at device 31.6 (no driver attached) fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0 orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 10.000 msec acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5% ad0: 57231MB <TOSHIBA MK6021GAS> [116280/16/63] at ata0-master UDMA100 acd0: CD-RW <TOSHIBA DVD-ROM SD-R2212> at ata1-master PIO4 MBREXT Slice 5 on ad0s3: 0000 00 01 81 fc 0c fe ff ff 3f 00 00 00 9d f1 30 01 |........?.....0.| [0] f:00 typ:12 s(CHS):252/1/129 e(CHS):255/254/255 s:63 l:19984797 0000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 Mounting root from ufs:/dev/ad0s4a WARNING: / was not properly dismounted WARNING: /tmp was not properly dismounted WARNING: /usr was not properly dismounted WARNING: /var was not properly dismounted /var: mount pending error: blocks 40 files 9 /var: superblock summary recomputed WARNING: /work was not properly dismounted system power profile changed to 'economy' system power profile changed to 'performance' system power profile changed to 'economy' system power profile changed to 'performance' Waiting (max 60 seconds) for system process `vnlru' to stop...stopped Waiting (max 60 seconds) for system process `bufdaemon' to stop...stopped Waiting (max 60 seconds) for system process `syncer' to stop...stopped syncing disks, buffers remaining... 1 1 done Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-RC1 #0: Sat Dec 7 22:16:29 GMT 2002 root@freebsd-current.sentex.ca:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc06b5000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc06b50a8. Timecounter "i8254" frequency 1193182 Hz Timecounter "TSC" frequency 2000079748 Hz CPU: Pentium 4 (2000.08-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 Features=0xffffffffbfebf9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,<b31>> real memory = 1073713152 (1023 MB) avail memory = 1036169216 (988 MB) Initializing GEOMetry subsystem Pentium Pro MTRR support enabled npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <ASUS P4_L3CS > on motherboard ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15 ACPI-0625: *** Info: GPE Block1 defined as GPE16 to GPE31 Using $PIR table, 6 entries at 0xc00f13b0 acpi0: power button is handled as a fixed feature programming model. Timecounter "ACPI-fast" frequency 3579545 Hz acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_tz0: <thermal zone> on acpi0 acpi_button0: <Sleep Button> on acpi0 acpi_acad0: <AC adapter> on acpi0 acpi_cmbat0: <Control method Battery> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <Intel 82845 host to AGP bridge> mem 0xe0000000-0xefffffff at device 0.0 on pci0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0xb800-0xb81f irq 5 at device 29.0 on pci0 usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0xb400-0xb41f irq 9 at device 29.1 on pci0 usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib2 rl0: <RealTek 8139 10/100BaseTX> port 0xa800-0xa8ff mem 0xd6800000-0xd68000ff irq 9 at device 5.0 on pci2 rl0: Realtek 8139B detected. Warning, this may be unstable in autoselect mode rl0: Ethernet address: 00:e0:18:bc:f6:85 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto cbb0: <RF5C476 PCI-CardBus Bridge> irq 5 at device 7.0 on pci2 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb1: <RF5C476 PCI-CardBus Bridge> irq 11 at device 7.1 on pci2 cardbus1: <CardBus bus> on cbb1 pccard1: <16-bit PCCard bus> on cbb1 pci2: <serial bus, FireWire> at device 7.2 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH3 ATA100 controller> port 0x8400-0x840f,0x8800-0x8803,0x9000-0x9007,0x9400-0x9403,0x9800-0x9807 mem 0xd5800000-0xd58003ff irq 9 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 pci0: <multimedia, audio> at device 31.5 (no driver attached) pci0: <simple comms> at device 31.6 (no driver attached) fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0 port 0x778-0x77b,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model Generic PS/2 mouse, device ID 0 acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0 orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 10.000 msec acpi_cpu: CPU throttling enabled, 8 steps from 100% to 12.5% ad0: 57231MB <TOSHIBA MK6021GAS> [116280/16/63] at ata0-master UDMA100 acd0: CD-RW <TOSHIBA DVD-ROM SD-R2212> at ata1-master PIO4 MBREXT Slice 5 on ad0s3: 0000 00 01 81 fc 0c fe ff ff 3f 00 00 00 9d f1 30 01 |........?.....0.| [0] f:00 typ:12 s(CHS):252/1/129 e(CHS):255/254/255 s:63 l:19984797 0000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 Mounting root from ufs:/dev/ad0s4a Fatal trap 12: page fault while in kernel mode fault virtual address = 0x42 fault code = supervisor read, page not present instruction pointer = 0x8:0xc042c517 stack pointer = 0x10:0xdf0c7a04 frame pointer = 0x10:0xdf0c7a1c code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 5 (acpi_task0) panic: from debugger Fatal trap 3: breakpoint instruction fault while in kernel mode instruction pointer = 0x8:0xc045c4f4 stack pointer = 0x10:0xdf0c7784 frame pointer = 0x10:0xdf0c7790 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = IOPL = 0 current process = 5 (acpi_task0) Fatal trap 12: page fault while in kernel mode fault virtual address = 0x42 fault code = supervisor read, page not present instruction pointer = 0x8:0xc042c517 stack pointer = 0x10:0xdf0c7a04 frame pointer = 0x10:0xdf0c7a1c code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 5 (acpi_task0) panic: from debugger Uptime: 1m14s Dumping 1023 MB ata0: resetting devices .. done 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320 336 352 368 384 400 416 432 448 464 480 496 512 528 544 560 576 592 608 624 640 656 672 688 704 720 736 752 768 784 800 816 832 848 864 880 896 912 928 944 960 976 992 1008 --- #0 doadump () at /usr/src/sys/kern/kern_shutdown.c:232 232 dumping++; (kgdb) where #0 doadump () at /usr/src/sys/kern/kern_shutdown.c:232 #1 0xc02ecfce in boot (howto=260) at /usr/src/sys/kern/kern_shutdown.c:364 #2 0xc02ed213 in panic () at /usr/src/sys/kern/kern_shutdown.c:517 #3 0xc015f7d2 in db_panic () at /usr/src/sys/ddb/db_command.c:450 #4 0xc015f752 in db_command (last_cmdp=0xc04f4500, cmd_table=0x0, aux_cmd_tablep=0xc04ea77c, aux_cmd_tablep_end=0xc04ea794) at /usr/src/sys/ddb/db_command.c:346 #5 0xc015f866 in db_command_loop () at /usr/src/sys/ddb/db_command.c:472 #6 0xc016255a in db_trap (type=12, code=0) at /usr/src/sys/ddb/db_trap.c:72 #7 0xc045c252 in kdb_trap (type=12, code=0, regs=0xdf0c79c4) at /usr/src/sys/i386/i386/db_interface.c:166 #8 0xc046dec2 in trap_fatal (frame=0xdf0c79c4, eva=0) at /usr/src/sys/i386/i386/trap.c:839 #9 0xc046dbd2 in trap_pfault (frame=0xdf0c79c4, usermode=0, eva=66) at /usr/src/sys/i386/i386/trap.c:758 #10 0xc046d72d in trap (frame= {tf_fs = 24, tf_es = 16, tf_ds = 16, tf_edi = -1038297720, tf_esi = 0, tf_ebp = -552830436, tf_isp = -552830480, tf_ebx = 1, tf_edx = -1038322144, tf_ecx = 1, tf_eax = 1, tf_trapno = 12, tf_err = 0, tf_eip = -1069365993, tf_cs = 8, tf_eflags = 66118, tf_esp = -1068373024, tf_ss = 1}) at /usr/src/sys/i386/i386/trap.c:445 #11 0xc045da38 in calltrap () at {standard input}:98 #12 0xc042332d in vm_fault (map=0xc0832000, vaddr=3735928832, fault_type=1 '\001', fault_flags=0) at /usr/src/sys/vm/vm_fault.c:281 #13 0xc046db71 in trap_pfault (frame=0xdf0c7bc0, usermode=0, eva=3735929054) at /usr/src/sys/i386/i386/trap.c:746 #14 0xc046d72d in trap (frame= {tf_fs = -1070727144, tf_es = -1066794992, tf_ds = 1039597584, tf_edi = 0, tf_esi = -1066784226, tf_ebp = -552829952, tf_isp = -552829972, tf_ebx = -1066784221, tf_edx = -559038242, tf_ecx = 1, tf_eax = 0, tf_trapno = 12, tf_err = 0, tf_eip = -1066903824, tf_cs = 8, tf_eflags = 66195, tf_esp = -552829912, tf_ss = -1066900995}) at /usr/src/sys/i386/i386/trap.c:445 #15 0xc045da38 in calltrap () at {standard input}:98 #16 0xc06861fd in ?? () #17 0xc0698933 in ?? () #18 0xc069a0e8 in ?? () #19 0xc0691b6d in ?? () #20 0xc069a06f in ?? () #21 0xc06999e4 in ?? () #22 0xc069c7d0 in ?? () #23 0xc02d98b5 in fork_exit (callout=0xc06a2a23, arg=0x0, frame=0x0) at /usr/src/sys/kern/kern_fork.c:866 (kgdb) up 12 #12 0xc042332d in vm_fault (map=0xc0832000, vaddr=3735928832, fault_type=1 '\001', fault_flags=0) at /usr/src/sys/vm/vm_fault.c:281 281 vm_object_pip_add(fs.first_object, 1); (kgdb) p fs.first_object $1 = (struct vm_object *) 0x0 To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-hackers" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3DF7470A.2060904>