Date: Sun, 15 Feb 1998 17:04:31 +0100 From: palme@uni-wuppertal.de (Hubert Palme) To: AIC7xxx@FreeBSD.ORG Cc: palme@rz.uni-wuppertal.de, palme@wrin27.urz.uni-wuppertal.de Subject: Non Ending Tape Problems :-( Message-ID: <199802151604.RAA11799@palme-pc.urz.Uni-Wuppertal.DE>
next in thread | raw e-mail | index | archive | help
Hello,
after upgrading the kernel to 2.0.33 (The former 2.0.29 suddenly begun
again with process hangups :-(), I have a new tape problem: After some
(long) time of writing, tar is cancelled with I/O Error. I tried
another tape, but the same problem. Short tars's were
successfull. This is the log:
Feb 15 14:58:45 palme-pc kernel: scsi0: Referenced SCB 255 not valid during SELTO.
Feb 15 14:58:45 palme-pc kernel: SCSISEQ = 0x5a SEQADDR = 0x4 SSTAT0 = 0x15 SSTAT1 = 0x8a
Feb 15 14:59:05 palme-pc kernel: scsi : aborting command due to timeout : pid 138981, scsi0, channel 0, id 1, lun 0 Read (10) 00 00 39 f9 34 00 00 02 00
Feb 15 14:59:06 palme-pc kernel: SCSI host 0 abort (pid 138981) timed out - resetting
Feb 15 14:59:06 palme-pc kernel: SCSI bus is being reset for host 0 channel 0.
And the second trial:
Feb 15 15:25:01 palme-pc kernel: scsi0: Referenced SCB 255 not valid during SELTO.
Feb 15 15:25:01 palme-pc kernel: SCSISEQ = 0x5a SEQADDR = 0x4 SSTAT0 = 0x15 SSTAT1 = 0x8a
Feb 15 15:25:21 palme-pc kernel: scsi : aborting command due to timeout : pid 157842, scsi0, channel 0, id 1, lun 0 Read (10) 00 00 28 d2 66 00 00 2e 00
Feb 15 15:25:21 palme-pc kernel: scsi : aborting command due to timeout : pid 157843, scsi0, channel 0, id 1, lun 0 Read (10) 00 00 39 f9 36 00 00 02 00
Feb 15 15:25:22 palme-pc kernel: SCSI host 0 abort (pid 157842) timed out - resetting
Feb 15 15:25:22 palme-pc kernel: SCSI bus is being reset for host 0 channel 0.
My configuration:
[16:47] ~>cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: IBM Model: DORS-32160 Rev: WA0A
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: TEAC Model: CD-ROM CD-56S Rev: 1.0D
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: HP Model: HP35480A Rev: T503
Type: Sequential-Access ANSI SCSI revision: 02
[16:51] ~>cat /proc/scsi/aic7xxx/0
Adaptec AIC7xxx driver version: 4.1.1/3.2.1
Compile Options:
AIC7XXX_RESET_DELAY : 15
AIC7XXX_TAGGED_QUEUEING: Enabled
AIC7XXX_PAGE_ENABLE : Enabled
AIC7XXX_PROC_STATS : Disabled
Adapter Configuration:
SCSI Adapter: Adaptec AHA-294X SCSI host adapter
(AIC-787x chipset)
Host Bus: Single
Base IO: 0x6100
Base IO Memory: 0xe2000000
IRQ: 11
SCBs: Used 9, HW 16, Page 255
Interrupts: 165633
Serial EEPROM: True
Extended Translation: Enabled
SCSI Bus Reset: Enabled
Ultra SCSI: Disabled
Disconnect Enable Flags: 0xff
Thanks in advance for any help!
--
Hubert Palme
palme@uni-wuppertal.de
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199802151604.RAA11799>