Date: Sat, 26 Dec 1998 16:35:35 -0800 From: yliao@pacbell.net To: Thierry.Herbelot@alcatel.fr, freebsd-questions@FreeBSD.ORG Subject: Re: Re : Question about installing FreeBSD 2.2.6 Message-ID: <368580D6.68CB2336@postoffice.pacbell.net> References: <H000057c01b3d12e@MHS>
next in thread | previous in thread | raw e-mail | index | archive | help
Hi, Could you give me more detailed explanations about installing 2.2.6-Release from hard disk, (How to copy files from CD to a FAT partition on hard disk? Which file to run to install and how to fetch updated versions of the atapi.c and atapi.h in the kernel sources.) because I am really not familiar with these procedures. Thanks. Carl Liao Thierry.Herbelot@alcatel.fr wrote: > Hello > > 2.2.6-Release has problems with ATAPI CD-ROMS (there are messages on > topic in the archives) > I would sugest : > - install a later release if you can (2.2.8 is released) > - if you can't : > * copy the minimal dists from the CD to a FAT partition on > your hard disk (including the kernel sources) > * install from the hard disk > * fetch updated versions of the atapi.c and atapi.h in the > kernel sources > * rebuild your kernel (read the handbook if you are not sure > of how to do it) > => then you can see your CD-ROM with 2.2.6 > > happy FreeBSD'ing > > TfH > > PS : anyway, booting from a CD-ROM is a matter of luck ;-) > > Dear Sir: > > > > I have a Dell Dimension XPS P100. It contains following components: > > Logitec System Mouse, 4X CD-ROM (IDE), US Robotics V.34 Sportster > > Data/Fax Modem (28.8), Creative Labs AWE32 Wavetable Soundcard, #9 Tri > > Graphics Accelerator PCI (2MB DRAM), 1 GB EIDE hard drive, 6.4 GB EIDE > > hard drive. > > > > When I tried to install FreeBSD 2.2.6 to my computer, I failed. The > > procedure I used is: > > a. Boot from CD-ROM. > > b. In the Kernel Configuration Menu, select Start kernel configuration > > in Visual Mode. > > c. Delete those devices my computer does not have ( but I do not know > > how I can add the information about Soundcard). > > d. Save changes and continue. > > > > After probing floppy, serial ports and hard drive etc. successfully, the > > system was locked up. Only the message "Probing devices, please wait ... > > " was displayed on the screen with blue background and never exited from > > such a state. > > > > Could somebody show me what is wrong with my installation and what I > > should do to solve installation problem. Thank you very much for your > > help. > > > > Carl Liao > > > > P.S.: following is the detailed information about my computer: > > > > >>> Logging System Resources > > > > === Current Configuration of Mother Board === > > # of functions = 17 > > slot # = 0 > > > > Function: Interrupt Controller > > not disabled, not locked, no config error > > I/O port: (20h-21h) (A0h-A1h) > > Interrupt: 2 > > > > Function: DMA Controller > > not disabled, not locked, no config error > > I/O port: (0h-Fh) (80h-90h) (94h-9Fh) (C0h-DEh) (40Bh-40Bh) > > (410h-42Fh) (430h-43Fh) (481h-483h) (487h-487h) > > (489h-48Ch) > > (4D6h-4D6h) > > DMA: 4 > > > > Function: System Timer Controller > > not disabled, not locked, no config error > > I/O port: (40h-43h) > > Interrupt: 0 > > > > Function: Real Time Clock Controller > > not disabled, not locked, no config error > > I/O port: (70h-71h) > > Interrupt: 8 > > > > Function: System Peripheral > > not disabled, not locked, no config error > > I/O port: (61h-61h) > > > > Function: System Peripheral > > not disabled, not locked, no config error > > I/O port: (F0h-FFh) > > Interrupt: 13 > > > > Function: Keyboard Controller > > not disabled, not locked, no config error > > I/O port: (60h-60h) (64h-64h) > > Interrupt: 1 > > > > Function: Mouse Controller > > not disabled, not locked, no config error > > Interrupt: 12 > > > > Function: RAM Controller > > not disabled, not locked, no config error > > Memory: (E8000h-FFFFFh) (0h-9FFFFh) (100000h-1FFFFFFh) > > (FFFC0000h-FFFFFFFFh) > > > > > > Function: PCI Bridge > > not disabled, not locked, no config error > > I/O port: (CF8h-CFFh) > > > > Function: Floppy Controller > > not disabled, not locked, no config error > > I/O port: (3F0h-3F5h) (3F7h-3F7h) > > DMA: 2 > > Interrupt: 6 > > > > Function: Parallel Port > > not disabled, not locked, no config error > > I/O port: (378h-37Bh) > > Interrupt: 7(sh) > > > > Function: Serial Port > > not disabled, not locked, no config error > > I/O port: (3F8h-3FFh) > > Interrupt: 4(sh) > > > > Function: Serial Port > > not disabled, not locked, no config error > > I/O port: (3E8h-3EFh) > > Interrupt: 4(sh) > > > > Function: IDE Controller > > not disabled, not locked, no config error > > I/O port: (1F0h-1F7h) (3F6h-3F6h) (FFA0h-FFA7h) > > Interrupt: 14 > > > > Function: IDE Controller > > not disabled, not locked, no config error > > I/O port: (170h-177h) (376h-376h) (FFA8h-FFAFh) > > Interrupt: 15 > > > > Function: System Peripheral > > not disabled, not locked, no config error > > I/O port: (78h-79h) > > > > === Current Configuration of unknown ISA card (ID: DEL0183) === > > # of functions = 3 > > slot # = 1 > > > > Function #1 > > not disabled, not locked, no config error > > I/O port: (220h-233h) (300h-301h) (388h-38Bh) > > DMA: 1 5 > > Interrupt: 5 > > > > Function #2 > > not disabled, not locked, no config error > > I/O port: (200h-207h) > > > > Function #3 > > not disabled, not locked, no config error > > > > === Current Configuration of ISA card USR 14,400 BPS DATA/FAX PC > > Internal Modem === > > # of functions = 1 > > slot # = 2 > > > > Function #1 > > not disabled, not locked, no config error > > I/O port: (2F8h-2FFh) > > Interrupt: 3 > > > > === Current Configuration of unknown ISA card (ID: A0) === > > # of functions = 0 > > slot # = 16 > > > > === Current Configuration of unknown ISA card (ID: PNPFFFF) === > > # of functions = 1 > > slot # = 15 > > > > Function #1 > > not disabled, not locked, no config error > > DMA: 3 7 > > Interrupt: 10 > > > > === Current Configuration of PCI card === > > # of functions = 1 > > slot # = 17 > > > > Function: VGA Controller > > not disabled, not locked, no config error > > I/O port: (3B4h-3B5h) (3BAh-3BAh) (3C0h-3CAh) (3CCh-3CCh) > > (3CEh-3CFh) > > (3D4h-3D5h) (3DAh-3DAh) > > Interrupt: 11(sh) > > Memory: (FF000000h-FF7FFFFFh) (C0000h-C7FFFh) (A0000h-AFFFFh) > > (B0000h-BFFFFh) > > > > > > > > > > To Unsubscribe: send mail to majordomo@FreeBSD.org > > with "unsubscribe freebsd-questions" in the body of the message To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?368580D6.68CB2336>