Date: Thu, 10 Nov 2011 19:29:48 +0100 From: rank1seeker@gmail.com To: hackers@freebsd.org, freebsd-acpi@FreeBSD.org Subject: Adventure into S3 state and back Message-ID: <20111110.182948.630.1@DOMY-PC>
next in thread | raw e-mail | index | archive | help
8.2-p4 RELEASE amd64
I've built a custom kernel, only with drivers, that I need
After resuming from S3 ...
I hit:
# ifconfig
and all hells breaks loose:
----
bge0: PHY read timed out (phy 1, reg 5, val 0xffffffff)
bge0: PHY read timed out (phy 1, reg 10, val 0xffffffff)
bge0: PHY read timed out (phy 1, reg 25, val 0xffffffff)
media: Ethernet autoselect
status: no carrier
bge0: PHY read timed out (phy 1, reg 1, val 0xffffffff)
bge0: PHY read timed out (phy 1, reg 1, val 0xffffffff)
bge0: PHY read timed out (phy 1, reg 0, val 0xffffffff)
ugen3.2: <Logitech> at usbus3 (disconnected)
ukbd0: at uhub3, port 1, addr 2 (disconnected)
ums0: at uhub3, port 1, addr 2 (disconnected)
uhid0: at uhub3, port 1, addr 2 (disconnected)
bge0: PHY read timed out (phy 1, reg 4, val 0xffffffff)
ugen3.2: <Logitech> at usbus3
ukbd0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 2> on usbus3
kbd2 at ukbd0
ums0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 2> on usbus3
ums0: 16 buttons and [XYZT] coordinates ID=2
uhid0: <Logitech USB Receiver, class 0/0, rev 2.00/12.01, addr 2> on usbus3
bge0: PHY read timed out (phy 1, reg 5, val 0xffffffff)
bge0: PHY read timed out (phy 1, reg 10, val 0xffffffff)
bge0: PHY read timed out (phy 1, reg 25, val 0xffffffff)
pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
nd6 options=3<PERFORMNUD,ACCEPT_RTADV>
cruiser# ifconfig
bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8009b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,LINKSTATE>
ether 00:21:70:70:01:df
bge0: PHY read timed out (phy 1, reg 1, val 0xffffffff)
bge0: PHY read timed out (phy 1, reg 1, val 0xffffffff)
... ... ... <You get the point>
----
So, taking into account:
"A common problem with suspend/resume is that many device drivers do not save, restore, or reinitialize their firmware, registers, or device memory properly."
Next step was to get rid of 'bge' device from my KERNCONF and recompile it.
Voila! S3 works!
But another, mouse problem, didn't go away!
In 9 out of 10 cases, mouse doesn't resume.
As it is USB mouse, I've did:
# camcontrol rescan all
didn't help
I've also tried adding into loader.conf and nada:
---
hint.psm.0.flags="0x3000"
---
But i think it is PS/2 related
What works 100% for a mouse is to unplug and then plug back it's USB receiver
This is Dell D830 laptop
Domagoj Smolčić
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20111110.182948.630.1>