Skip site navigation (1)Skip section navigation (2)
Date:      Wed, 19 Nov 2003 13:07:48 -0500
From:      "John Straiton" <jsmailing@clickcom.com>
To:        "'Chip McClure'" <vhm3@gigguardian.com>
Cc:        freebsd-isp@freebsd.org
Subject:   RE: Dual Ethernet NIC w/ failover
Message-ID:  <20031119181529.E6061146C67@mx1.clickcom.com>
In-Reply-To: <23310.216.195.235.103.1069264920.squirrel@webmail.gigguardian.com>

next in thread | previous in thread | raw e-mail | index | archive | help
I had thought about that as a possibility. My thought was if I created like
a /dev/ether0 and then symlink'ed it to /dev/fxp0, in the event of a
failure, I could just change the link over to fxp1 and my firewall rules,
dhcpd configurations, et al would still work since they were just reference
the symlink (assuming I can do something oddball like that).

I was just hoping that someone with more skill than I had put together a
more fluid means of all this happening..

Thanks,
John
 

> -----Original Message-----
> From: Chip McClure [mailto:vhm3@gigguardian.com] 
> Sent: Wednesday, November 19, 2003 1:02 PM
> To: jsmailing@clickcom.com
> Cc: freebsd-isp@freebsd.org
> Subject: Re: Dual Ethernet NIC w/ failover
> 
> John Straiton said:
> 
> Hello John,
> 
> Although I didn't do this for any gigabit nic's, it should 
> work the same, no less.
> 
> I worte up a small shell script, that pings the gateway 
> device. If the ping fails, the shell script de-configures the 
> primary interface of that card, and configures the secondary 
> interface, assuming the identity of the 1st interface. she 
> shell script also write a value to a text file, as to which 
> is the active interface, so it knows to revert back, if the 
> secondary were to fail. This script was added into the cron 
> job, to run every minute.
> 
> Chip
> 
> > Greets!
> > 	I have seen a number of posts regarding support of the 
> dual ethernet 
> > cards, however I haven't seen a lot of posts regarding the 
> > availability of dual ethernet cards with working failover 
> software... 
> > I have a couple of the Intel 10/100/1000's on hand but it 
> appears that 
> > the software they use only comes in a linux binary. I'm a 
> bit leary of 
> > trying to shoehorn it into working with the linux binary 
> compatibility 
> > (assuming I could) since the whole purpose of having a dual 
> ethernet 
> > NIC is to take variables *out* of the networking.
> > 	I'm looking to try to hook a 5.1-R machine up to two separate 
> > switches that connect to the same core and run spanning 
> tree so that a 
> > failure in either a switch or a network cable would 
> automagically fail 
> > over to the other port at the same IP.
> > 	Does anyone have any suggestions on dual gigabit NICs 
> that they have 
> > been able to get into switch-failover mode?
> >
> > John Straiton
> > jks@ clickcom.com
> > Clickcom, Inc
> > 704-365-9970x101
> >
> >
> > _______________________________________________
> > freebsd-isp@freebsd.org mailing list
> > http://lists.freebsd.org/mailman/listinfo/freebsd-isp
> > To unsubscribe, send any mail to 
> "freebsd-isp-unsubscribe@freebsd.org"
> 
> 
> -----
> Chip McClure
> Sr. Unix Administrator
> GigGuardian, Inc.
> 
> http://www.gigguardian.com/
> -----
> 
> 
> 




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20031119181529.E6061146C67>