Date: Sun, 13 May 2007 05:22:32 GMT From: Sepherosa Ziehau <sephe@FreeBSD.org> To: Perforce Change Reviews <perforce@FreeBSD.org> Subject: PERFORCE change 119755 for review Message-ID: <200705130522.l4D5MWFw054522@repoman.freebsd.org>
next in thread | raw e-mail | index | archive | help
http://perforce.freebsd.org/chv.cgi?CH=119755 Change 119755 by sephe@sephe_zealot:sam_wifi on 2007/05/13 05:21:31 u_intX_t -> uintX_t Approved by: sam Affected files ... .. //depot/projects/wifi/sys/net80211/ieee80211_radiotap.h#11 edit Differences ... ==== //depot/projects/wifi/sys/net80211/ieee80211_radiotap.h#11 (text+ko) ==== @@ -60,18 +60,18 @@ * Note well: all radiotap fields are little-endian. */ struct ieee80211_radiotap_header { - u_int8_t it_version; /* Version 0. Only increases + uint8_t it_version; /* Version 0. Only increases * for drastic changes, * introduction of compatible * new fields does not count. */ - u_int8_t it_pad; - u_int16_t it_len; /* length of the whole + uint8_t it_pad; + uint16_t it_len; /* length of the whole * header in bytes, including * it_version, it_pad, * it_len, and data fields. */ - u_int32_t it_present; /* A bitmap telling which + uint32_t it_present; /* A bitmap telling which * fields are present. Set bit 31 * (0x80000000) to extend the * bitmap by another 32 bits. @@ -84,22 +84,22 @@ * Name Data type Units * ---- --------- ----- * - * IEEE80211_RADIOTAP_TSFT u_int64_t microseconds + * IEEE80211_RADIOTAP_TSFT uint64_t microseconds * * Value in microseconds of the MAC's 64-bit 802.11 Time * Synchronization Function timer when the first bit of the * MPDU arrived at the MAC. For received frames, only. * - * IEEE80211_RADIOTAP_CHANNEL 2 x u_int16_t MHz, bitmap + * IEEE80211_RADIOTAP_CHANNEL 2 x uint16_t MHz, bitmap * * Tx/Rx frequency in MHz, followed by flags (see below). * - * IEEE80211_RADIOTAP_FHSS u_int16_t see below + * IEEE80211_RADIOTAP_FHSS uint16_t see below * * For frequency-hopping radios, the hop set (first byte) * and pattern (second byte). * - * IEEE80211_RADIOTAP_RATE u_int8_t 500kb/s or index + * IEEE80211_RADIOTAP_RATE uint8_t 500kb/s or index * * Tx/Rx data rate. If bit 0x80 is set then it represents an * an MCS index and not an IEEE rate. @@ -116,30 +116,30 @@ * RF noise power at the antenna, decibel difference from one * milliwatt. * - * IEEE80211_RADIOTAP_DB_ANTSIGNAL u_int8_t decibel (dB) + * IEEE80211_RADIOTAP_DB_ANTSIGNAL uint8_t decibel (dB) * * RF signal power at the antenna, decibel difference from an * arbitrary, fixed reference. * - * IEEE80211_RADIOTAP_DB_ANTNOISE u_int8_t decibel (dB) + * IEEE80211_RADIOTAP_DB_ANTNOISE uint8_t decibel (dB) * * RF noise power at the antenna, decibel difference from an * arbitrary, fixed reference point. * - * IEEE80211_RADIOTAP_LOCK_QUALITY u_int16_t unitless + * IEEE80211_RADIOTAP_LOCK_QUALITY uint16_t unitless * * Quality of Barker code lock. Unitless. Monotonically * nondecreasing with "better" lock strength. Called "Signal * Quality" in datasheets. (Is there a standard way to measure * this?) * - * IEEE80211_RADIOTAP_TX_ATTENUATION u_int16_t unitless + * IEEE80211_RADIOTAP_TX_ATTENUATION uint16_t unitless * * Transmit power expressed as unitless distance from max * power set at factory calibration. 0 is max power. * Monotonically nondecreasing with lower power levels. * - * IEEE80211_RADIOTAP_DB_TX_ATTENUATION u_int16_t decibels (dB) + * IEEE80211_RADIOTAP_DB_TX_ATTENUATION uint16_t decibels (dB) * * Transmit power expressed as decibel distance from max power * set at factory calibration. 0 is max power. Monotonically @@ -152,20 +152,20 @@ * reference). This is the absolute power level measured at * the antenna port. * - * IEEE80211_RADIOTAP_FLAGS u_int8_t bitmap + * IEEE80211_RADIOTAP_FLAGS uint8_t bitmap * * Properties of transmitted and received frames. See flags * defined below. * - * IEEE80211_RADIOTAP_ANTENNA u_int8_t antenna index + * IEEE80211_RADIOTAP_ANTENNA uint8_t antenna index * * Unitless indication of the Rx/Tx antenna for this packet. * The first antenna is antenna 0. * - * IEEE80211_RADIOTAP_XCHANNEL u_int32_t bitmap - * u_int16_t MHz - * u_int8_t channel number - * u_int8_t .5 dBm + * IEEE80211_RADIOTAP_XCHANNEL uint32_t bitmap + * uint16_t MHz + * uint8_t channel number + * uint8_t .5 dBm * * Extended channel specification: flags (see below) followed by * frequency in MHz, the corresponding IEEE channel number, and
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?200705130522.l4D5MWFw054522>