From owner-freebsd-current Tue Aug 10 20: 5: 9 1999 Delivered-To: freebsd-current@freebsd.org Received: from web1002.mail.yahoo.com (web1002.mail.yahoo.com [128.11.23.92]) by hub.freebsd.org (Postfix) with SMTP id F360D14F3F for ; Tue, 10 Aug 1999 20:05:06 -0700 (PDT) (envelope-from bvmcg@yahoo.com) Message-ID: <19990811030509.3860.rocketmail@web1002.mail.yahoo.com> Received: from [24.29.199.43] by web1002.mail.yahoo.com; Tue, 10 Aug 1999 20:05:09 PDT Date: Tue, 10 Aug 1999 20:05:09 -0700 (PDT) From: Brian McGroarty Reply-To: brian@pobox.com Subject: Re: ATA - Trouble mounting secondary master To: Kevin Street , freebsd-current@FreeBSD.ORG Cc: brian@pobox.com MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Sender: owner-freebsd-current@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Also of interest - I have a seperate access light for each of my drives, as they're in removable bays. I notice the access light for the secondary master remaining on after the kernel driver has done its scanning. The light goes off on this, the failed first access. I believe the light for the primary slave stays on as well, but goes off on the first access to the primary master (which does -not- fail). --- Kevin Street wrote: > Brian McGroarty writes: > > > In using the ATA driver, I'm unable to automatically mount a > > partition on a master drive on the secondary controller. > fsck > > complains that device rwd2s1e isn't configured and exists. > > Immediately mounting by hand works perfectly. > > Nice timing, I was about to send a message with a description > of a > similar (the same?) problem. The first access to any IDE disk > (except > the one I'm booting from - wd1) fails with 'device not > configured'. This > affects swapon for wd2s2b during the boot as well as the first > mount > for wd0 which happens to have only dos partitions on it. So > the > problem is not restricted to ufs partitions or to the > secondary > controller. > > Repeating the swapon or mount command works normally. > > I've been seeing this problem for about a month, but I've been > away on > vacation so am just beginning to look into it. I made changes > to all > my drives and put them in LBA mode at about the same time as I > began > seeing this, but I'm not sure if that is related. > > ata-pci0: at device 4.1 on pci0 > ata-pci0: Busmastering DMA supported > ata0 at 0x01f0 irq 14 on ata-pci0 > ata1 at 0x0170 irq 15 on ata-pci0 > > ata0: master: setting up UDMA2 mode on PIIX4 chip OK > ad0: ATA-4 disk at ata0 as master > ad0: 9787MB (20044080 sectors), 19885 cyls, 16 heads, 63 S/T, > 512 B/S > ad0: piomode=4, dmamode=2, udmamode=2 > ad0: 16 secs/int, 0 depth queue, DMA mode > ata0: slave: setting up UDMA2 mode on PIIX4 chip OK > ad1: ATA-3 disk at ata0 as slave > ad1: 8063MB (16514064 sectors), 16383 cyls, 16 heads, 63 S/T, > 512 B/S > ad1: piomode=4, dmamode=2, udmamode=2 > ad1: 16 secs/int, 0 depth queue, DMA mode > ata1: master: setting up UDMA2 mode on PIIX4 chip OK > ad2: ATA-4 disk at ata1 as master > ad2: 6149MB (12594960 sectors), 13328 cyls, 15 heads, 63 S/T, > 512 B/S > ad2: piomode=4, dmamode=2, udmamode=2 > ad2: 16 secs/int, 0 depth queue, DMA mode > acd0: CDROM drive at ata1 as slave > acd0: drive speed 5515KB/sec, 256KB cache > acd0: supported read types: CD-R, CD-RW, CD-DA > acd0: Audio: play, 256 volume levels > acd0: Mechanism: ejectable tray > acd0: Medium: CD-ROM 120mm data disc loaded, unlocked _____________________________________________________________ Do You Yahoo!? Bid and sell for free at http://auctions.yahoo.com To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-current" in the body of the message