From owner-freebsd-questions Thu May 21 15:45:20 1998 Return-Path: Received: (from majordom@localhost) by hub.freebsd.org (8.8.8/8.8.8) id PAA19340 for freebsd-questions-outgoing; Thu, 21 May 1998 15:45:20 -0700 (PDT) (envelope-from owner-freebsd-questions@FreeBSD.ORG) Received: from abby.skypoint.net (abby.skypoint.net [199.86.32.252]) by hub.freebsd.org (8.8.8/8.8.8) with ESMTP id PAA19158 for ; Thu, 21 May 1998 15:44:17 -0700 (PDT) (envelope-from rpj@fep.hirshfields.com) Received: (from uucp@localhost) by abby.skypoint.net (8.8.7/jl 1.3) with UUCP id RAA22825 for freebsd-questions@freebsd.org; Thu, 21 May 1998 17:44:09 -0500 (CDT) Received: (from rpj@localhost) by fep.hirshfields.com (8.8.5/8.8.5) id QAA02379 for freebsd-questions@freebsd.org; Thu, 21 May 1998 16:58:03 -0500 (CDT) From: "Roger P. Johnson" Message-Id: <199805212158.QAA02379@fep.hirshfields.com> Subject: I got 2940UW timeout problem also ... help please ... To: freebsd-questions@FreeBSD.ORG Date: Thu, 21 May 1998 16:58:02 -0500 (CDT) X-Mailer: ELM [version 2.4ME+ PL22 (25)] MIME-Version: 1.0 Content-Type: text/plain; charset=US-ASCII Content-Transfer-Encoding: 7bit Sender: owner-freebsd-questions@FreeBSD.ORG Precedence: bulk X-Loop: FreeBSD.ORG Hi. OK. I have searched the archives, etc. and still need help on what appears to be an age old problem with these 2940UW's. I cannot install FreeBSD 2.2.6 or 2.2.2 onto this configuration: DEC Celebris 590 16 MB RAM 2940UW BIOS ver. 1.32 Seagate ST34572W 4550MB Barracuda (Ultra Wide; 68 pin) Panasonic SCSI-2 CD-ROM. At the very basic level, I only have the 2940UW and the HD installed. Forget the CD-ROM at this point. Don't even have the 50 pin cable attached (not that it mattered). I am only using the 68 pin cable to the hard drive which is terminated by the hard drive on the very last connector. After FreeBSD boots up from the floppy, I finish the visual configuration and the 2940UW is reconized, and I have to wait for the SCSI devices to settle. Then big long pause while it times out on all along the chain. If you leave it long enough you get the installation menu, and then she reboots and does it all over again. So I try this: I have a working FreeBSD 2.2.2 on a 1GB narrow SCSI-3 hd via 2940AU card. I plug this working hard drive into the end connector of the 50 pin ribbon cable attached to the 2940UW, remove the 68 pin wide cable an try to boot. I get the same problem. It will load the boot block off of the hard disk, but after letting the scsi devices settle, it times out etc etc. etc. Help! What can I do? I have tried dinging with the 2940UW BIOS settings many a times, and can't get see what's wrong. Tried the messing with the termination settings (don't see what was wrong with them anyways). Using the adaptors defaults, with the wide hard drive w/termination, all in its basic form doesn't work either. Any patches I need? Any pointers are really welcomed here. I know there are lots of people using the aic-7880 controller. roger rjohnson@hirshfields.com To Unsubscribe: send mail to majordomo@FreeBSD.org with "unsubscribe freebsd-questions" in the body of the message