Skip site navigation (1)Skip section navigation (2)
Date:      Mon, 3 Oct 2005 09:38:01 -0700
From:      Luigi Rizzo <rizzo@icir.org>
To:        Patrick Tracanelli <eksffa@freebsdbrasil.com.br>
Cc:        ipfw@freebsd.org
Subject:   Re: layer2 filtering and dummynet, bw reduced by half
Message-ID:  <20051003093801.B92958@xorpc.icir.org>
In-Reply-To: <43415BFB.1050800@freebsdbrasil.com.br>; from eksffa@freebsdbrasil.com.br on Mon, Oct 03, 2005 at 01:27:39PM -0300
References:  <4341575C.8080409@freebsdbrasil.com.br> <20051003091024.A92958@xorpc.icir.org> <43415BFB.1050800@freebsdbrasil.com.br>

next in thread | previous in thread | raw e-mail | index | archive | help
see the ipfw manpage near the eginning with the graph
showing the packet flow.

"layer2" means the rule matches only on layer2.
"not layer2" matches only on layer 3.
if you don't put anything, it matches both layer2 and layer3.

luigi

On Mon, Oct 03, 2005 at 01:27:39PM -0300, Patrick Tracanelli wrote:
> Luigi Rizzo wrote:
> > you are passing traffic through the pipe twice.
> > you have to decide if your rules should apply tto
> > layer2 or not and write the rules accordingly
> 
> Why are they going twice through the pipe? When net.link.ether.ipfw=1 
> you pass it through all rules twice? "first match wins" does not apply? 
> How should it be made to do it passing only once? I have just tried:
> 
> ipfw add 400 count log all from any to any in layer2
> ipfw add 401 count log all from any to any out layer2
> 
> Where hopefully it would be passed only once (when passing layer2 rules) 
> but it did not.
> 
> How could the rules be written to filter layer2 instead, in the given 
> circunstances? 'Cos you say it should be written to apply to layer2 or 
> not, and write the rules "accordingly", but in the following circunstance:
> 
> 00400    54     4566 count log ip from any to any in
> 00401    42     4300 count log ip from any to any out
> 00501    16     1616 pipe 1 ip from any to 172.16.52.254 in
> 00601    16     1428 pipe 2 ip from 172.16.52.254 to any out
> 65535 22052 10476881 allow ip from any to any
> 
> There is no layer2 rule, but if net.link.ether.ipfw=1 the /2 bw limiting 
> happens again. So it does not seem to be a matter of how to write the 
> rules, but instead, to have net.link.ether.ipfw=1 or not.
> 
> Or did I miss some point?
> 
> 
> >>layer2() {
> >>         ipfw add skipto 400 all from any to any mac-type ip,arp layer2
> >>         ipfw add deny all from any to any layer2
> >>}
> >>
> >>countlog() {
> >>         ipfw add 400 count log all from any to any in
> >>         ipfw add 401 count log all from any to any out
> >>}
> >>
> >>pipe() {
> >>         ipfw add pipe 1 all from any to 172.16.52.254/32 in
> >>         ipfw add pipe 2 all from 172.16.52.254/32 to any out
> >>         ipfw pipe 1 config bw 64Kbps queue 5
> >>         ipfw pipe 2 config bw 64Kbps queue 5
> >>}
> 
> 
> -- 
> Patrick Tracanelli



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20051003093801.B92958>