Date: Thu, 26 Jan 2012 13:54:23 -0500 From: Super Bisquit <superbisquit@gmail.com> To: Justin Hibbits <chmeeedalf@gmail.com> Cc: FreeBSD PowerPC ML <freebsd-ppc@freebsd.org> Subject: Re: Has source been updated with Hibbits' recent patches? Message-ID: <CA%2BWntOsdQpTiAgFor4FVjYw4KjNVvyiatXPo8wg5bNs9%2BLZ6=g@mail.gmail.com> In-Reply-To: <CA%2BWntOvbyPUv58uC-Ycc6KjiBpo8_mzGz6inZdXi-SgsCq5mcA@mail.gmail.com> References: <CA%2BWntOuBdgcXow13BtfgVLfD3Bj0gT-WJ55X5HfUHoXxx7GD9Q@mail.gmail.com> <6B0E21DA-728B-43ED-8194-76D48A65B885@gmail.com> <CA%2BWntOt-MgYmuYjCgnbkUpyPmpWXgRM1UababbR8VabaYrP-Zw@mail.gmail.com> <CA%2BWntOvfJyXq2Ev%2BEAHS2GoiOX7qgpvfNb0uDW8WJ9TFvY9jNA@mail.gmail.com> <CAHSQbTC7amxv_4E8yj0LfTSXYGgdiyZ2hxv-hw3Fy3P_h5PNFA@mail.gmail.com> <CA%2BWntOvbyPUv58uC-Ycc6KjiBpo8_mzGz6inZdXi-SgsCq5mcA@mail.gmail.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Okay. Is there a new patch available? Would you like for me to boot the device with a Linux PPC disk to see what exact card it is? On 1/20/12, Super Bisquit <superbisquit@gmail.com> wrote: > No wi0 comes up but there is the ukphy0 which is an 802.3u device. > There is a chance of recognizing the exact card with an OpenBSD or Linux > PowerPC disk. > > On Thu, Jan 19, 2012 at 3:21 PM, Justin Hibbits > <chmeeedalf@gmail.com>wrote: > >> On Wed, Jan 18, 2012 at 9:52 PM, Super Bisquit >> <superbisquit@gmail.com>wrote: >> >>> I've successfully applied the patches. Now, is the next step rebuilding >>> the kernel? >>> tima# kldstat >>> Id Refs Address Size Name >>> 1 24 0x100000 923e20 kernel >>> 2 1 0xd1480000 1d000 if_wi.ko >>> 3 9 0xd149d000 7a000 wlan.ko >>> 4 1 0xd1523000 13000 wlan_acl.ko >>> 5 1 0xd1536000 12000 wlan_amrr.ko >>> 6 1 0xd1548000 17000 wlan_ccmp.ko >>> 7 1 0xd155f000 12000 wlan_rssadapt.ko >>> 8 1 0xd1571000 14000 wlan_tkip.ko >>> 9 1 0xd1585000 12000 wlan_wep.ko >>> 10 1 0xd1597000 11000 wlan_xauth.ko >>> >>> tima# ifconfig -a >>> usbus0: flags=10001<UP> metric 0 mtu 0 >>> usbus1: flags=10001<UP> metric 0 mtu 0 >>> fwe0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 >>> options=8<VLAN_MTU> >>> ether 02:0a:95:93:a8:20 >>> ch 1 dma -1 >>> gem0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu >>> 1500 >>> options=8000b<RXCSUM,TXCSUM,VLAN_MTU,LINKSTATE> >>> ether 00:0a:95:93:a8:20 >>> inet 98.211.76.206 netmask 0xfffffc00 broadcast 255.255.255.255 >>> media: Ethernet autoselect (100baseTX <full-duplex>) >>> status: active >>> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 >>> options=3<RXCSUM,TXCSUM> >>> inet 127.0.0.1 netmask 0xff000000 >>> inet6 ::1 prefixlen 128 >>> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 >>> nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> >>> tima# dmesg|grep miibus >>> miibus0: <MII bus> on gem0 >>> ukphy0: <Generic IEEE 802.3u media interface> PHY 0 on miibus0 >>> interface miibus.1 already present in the KLD 'kernel'! >>> >>> tima# pciconf -l -b >>> hostb0@pci0:0:11:0: class=0x060000 card=0x00000000 chip=0x0027106b >>> rev=0x00 hdr=0x00 >>> vgapci0@pci0:0:16:0: class=0x030000 card=0x00000000 chip=0x011010de >>> rev=0xb2 hdr=0x00 >>> bar [10] = type Memory, range 32, base 0x91000000, size 16777216, >>> enabled >>> bar [14] = type Prefetchable Memory, range 32, base 0x98000000, >>> size 134217728, enabled >>> macio0@pci1:0:23:0: class=0xff0000 card=0x00000000 chip=0x0025106b >>> rev=0x00 hdr=0x00 >>> bar [10] = type Memory, range 32, base 0x80000000, size 524288, >>> enabled >>> ohci0@pci1:0:24:0: class=0x0c0310 card=0x00000000 chip=0x0026106b >>> rev=0x00 hdr=0x00 >>> bar [10] = type Memory, range 32, base 0x80081000, size 4096, >>> enabled >>> ohci1@pci1:0:25:0: class=0x0c0310 card=0x00000000 chip=0x0026106b >>> rev=0x00 hdr=0x00 >>> bar [10] = type Memory, range 32, base 0x80080000, size 4096, >>> enabled >>> hostb1@pci1:0:11:0: class=0x060000 card=0x00000000 chip=0x0028106b >>> rev=0x00 hdr=0x00 >>> fwohci0@pci2:0:14:0: class=0x0c0010 card=0x0030106b chip=0x0030106b >>> rev=0x00 hdr=0x00 >>> bar [10] = type Memory, range 32, base 0xf5000000, size 4096, >>> enabled >>> gem0@pci2:0:15:0: class=0x020000 card=0x00000000 chip=0x0024106b >>> rev=0x00 hdr=0x00 >>> bar [10] = type Memory, range 32, base 0xf5200000, size 2097152, >>> enabled >>> hostb2@pci2:0:11:0: class=0x060000 card=0x00000000 chip=0x0029106b >>> rev=0x00 hdr=0x00 >>> >>> ima# ifconfig wlan create wlandev gem0 >>> ifconfig: SIOCIFCREATE2: Device not configured >>> tima# >>> >>> Unfortunately, I'm having trouble creating the interface. >>> >>> I haven't rebuilt the kernel for the ofw brightness patch. >>> >>> >>> >>> >>> >>> On Tue, Jan 17, 2012 at 7:37 PM, Super Bisquit >>> <superbisquit@gmail.com>wrote: >>> >>>> I should have an internet connection up again in the next few days. I >>>> downloaded the two files. >>>> Wow. Nobody? That blows. >>>> Give me a few days or less to get back to you. >>>> >>>> On 1/17/12, Justin Hibbits <chmeeedalf@gmail.com> wrote: >>>> > On Jan 17, 2012, at 5:19 PM, Super Bisquit wrote: >>>> > >>>> >> I'm referring to the AirPort and tty/syscons brightness patches. >>>> > >>>> > No. The brightness patch may or may not go in. The Airport patch >>>> > will go in once I get some test results (have you tested it?). >>>> > Nobody's given me any test results, and last time I tried I was >>>> > having >>>> > issues (attached fine, but couldn't send/receive). Haven't looked at >>>> > it in a couple months though. >>>> > >>>> > - Justin >>>> > >>>> >>> >>> >> This shows to me that it hasn't found the airport card, because there's >> no >> wi0 listed in ifconfig. Can you boot verbose and send me the dmesg from >> that boot? >> >> - Justin >> >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?CA%2BWntOsdQpTiAgFor4FVjYw4KjNVvyiatXPo8wg5bNs9%2BLZ6=g>