Date: Tue, 22 Jun 2021 03:09:38 -0700 From: Mark Millard via freebsd-arm <freebsd-arm@freebsd.org> To: dsl@mcusim.org Cc: freebsd-arm <freebsd-arm@freebsd.org> Subject: Re: HoneyComb first-boot notes Message-ID: <A8469092-0001-4442-B90C-F3960B85D829@yahoo.com> In-Reply-To: <YNGrdIhpdupSXm2a@x230.ds> References: <8A6C415F-A57B-4F2F-861F-052B487166D6.ref@yahoo.com> <8A6C415F-A57B-4F2F-861F-052B487166D6@yahoo.com> <YNGT5hcHOBd6cU4T@x230.ds> <40AE6447-77AF-4D0E-864F-AD52D9F3346F@yahoo.com> <YNGf999RsaTfNhcp@x230.ds> <0DF376DC-C4A5-494C-BAA5-782516596CF0@yahoo.com> <YNGrdIhpdupSXm2a@x230.ds>
next in thread | previous in thread | raw e-mail | index | archive | help
> On 2021-Jun-22, at 02:20, Dmitry Salychev via freebsd-arm <freebsd-arm = at freebsd.org> wrote: >=20 >=20 >>>>>> I put an existing FreeBSD Optane into a just delivered >>>>>> HoneyComb, put in the RAM and the matching UEFI/ACPI >>>>>> image on a microsd card and put the card in the slot. >>>>>> I plugged in a USB3 Ethernet dongle, like I use on some >>>>>> other systems. Serial console via its USB port for such. >>>>>> (Optane instead of video card.) The UEFI/ACPI image was >>>>>> extracted from: >>>>>>=20 >>>>>> = https://solid-run-images.sos-de-fra-1.exo.io/LX2k/lx2160a_uefi/lx2160acex7= _2000_700_2900_8_5_2_sd_81b4bbe.img.xz >>>>>>=20 >>>>>> in order to match the RAM and being based on the >>>>>> most current vintage at: >>>>>>=20 >>>>>> https://github.com/SolidRun/lx2160a_uefi/ >>>>>>=20 >>>>>> It booted. >>>>>=20 >>>>> Could you share whole dmesg? >>>>=20 >>>> I've not done a "boot -v" . The below is actually from a >>>> captured serial console output. It is lightly edited. I >>>> have omitted nearly all loader output (and before). >>>>=20 >>>=20 >>> Thanks for sharing. Have you seen somewhere in output from UEFI = (before >>> the loader) that "DPAA2 Management Complex initialized"? >>=20 >> The text "DPAA2" does not occur in the captured output >> at all. However, that is my understanding of the expected >> status. >=20 > That's strange because DPAA2 firmware should be included into UEFI = built from > lx2160a_uefi: >=20 > = https://github.com/SolidRun/edk2-platforms/blob/edk2-stable202102-lx2160ac= ex7/Platform/SolidRun/LX2160aCex7/LX2160aCex7.fdf#L252 >=20 > I assumed that there might be any output that firmware has been loaded = correctly > at least. The edk2 build is not a debug build and, before putting up the menu, only outputs (I stripped some escape sequences): =00NOTICE: BL2: v2.4(release):v2.0-4462-ge7b392d0a NOTICE: BL2: Built : 07:47:06, May 31 2021 NOTICE: UDIMM KHX2933C17S4/32G =20 NOTICE: DDR4 UDIMM with 2-rank 64-bit bus (x8) NOTICE: 64 GB DDR4, 64-bit, CL=3D17, ECC off, 256B, CS0+CS1 NOTICE: BL2: Booting BL31 NOTICE: BL31: v2.4(release):v2.0-4462-ge7b392d0a NOTICE: BL31: Built : 07:47:10, May 31 2021 NOTICE: Welcome to lx2160acex7 BL31 Phase UEFI firmware built at 07:44:26 on May 31 2021. version: 202102 SOC: LX2160ACE Rev2.0 (0x87360020) UEFI firmware (version 202102 built at 07:44:28 on May 31 2021) Tianocore/EDK2 firmware version 202102 Press ESCAPE for boot options .... After the menu things start with basically: Consoles: serial port =20 = |=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08= \=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08-=08\=08|=08/=08= -=08\=08|=08/=08-=08\=08 Reading loader env vars from = /efi/freebsd/loader.env Setting currdev to disk2p1: |=08/=08-=08\=08|=08/=08FreeBSD/arm64 EFI loader, Revision 1.1 Command line arguments: loader.efi Image base: 0xedc89000 EFI version: 2.70 EFI Firmware: EDK II (rev 0.00) Console: comconsole (0) Load Path: \EFI\BOOT\BOOTAA64.EFI . . . One might be able to make inferences from the content of some potential menu displays. Otherwise, I expect that a debug build would be required to see DPAA2 references. I do not expect one can validly infer much from the lack of "DPAA2" text in my boot sequence (with any capitalization vs. lower case status). =3D=3D=3D Mark Millard marklmi at yahoo.com ( dsl-only.net went away in early 2018-Mar)
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?A8469092-0001-4442-B90C-F3960B85D829>