Date: Fri, 15 Aug 2003 08:18:30 -0500 From: "Joey Mingrone" <mingrone@hotmail.com> To: support@bluetooth-shop.sk Cc: questions@freebsd.org Subject: Re: Nwe kernel and dmesg question Message-ID: <Sea2-F42Y6dc6S3GE8Z00039379@hotmail.com>
next in thread | raw e-mail | index | archive | help
Hey Peter, To get rid of the error messages on boot up, you can remove devices you are not using from /boot/kernel.conf. Joey > >Hello everybody, > >I'm sorry for the long mail, but I really need your help. Please read it >before removing :-) > >I just have my new kernel (where I disabled almost SCSI devices) but during >start-up there are errors as follows: > >config> di pcic0 >No such device: pcic0 >Invalid command or syntax. Type `?' for help. >config> di bt0 >No such device: bt0 >Invalid command or syntax. Type `?' for help. >config> di aic0 >No such device: aic0 >Invalid command or syntax. Type `?' for help. >config> di aha0 >No such device: aha0 >Invalid command or syntax. Type `?' for help. >config> di adv0 >No such device: adv0 >Invalid command or syntax. Type `?' for help. >config> en ed0 >No such device: ed0 >Invalid command or syntax. Type `?' for help. >config> po ed0 0x280 >No such device: ed0 >Invalid command or syntax. Type `?' for help. >config> ir ed0 10 >No such device: ed0 >Invalid command or syntax. Type `?' for help. >config> iom ed0 0xd8000 >No such device: ed0 >Invalid command or syntax. Type `?' for help. >config> f ed0 0 >No such device: ed0 >Invalid command or syntax. Type `?' for help. > >What are these devices ? Why they are there, when I rem all lines >concerning >about them in my kernel config file ? > > >Also, my machine has Matrox Millenium card. I tried tu set it up into VESA >mode and use 132x43 cols/lns, but the last message before showing login >screen is: "vidcontrol: cannot set video mode. Operation not supported by >device". Matrox was found: > >VESA: v2.0, 2048k memory, flags:0x1, mode table:0xc030a302 (1000022) >VESA: Matrox Graphics Inc. >[skipped] >pci0: <Matrox MGA Millennium 2064W graphics accelerator> at 11.0 irq 11 > >but sc0 still goes into VGA mode: > >vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 >sc0: <System console> at flags 0x100 on isa0 >sc0: VGA <16 virtual consoles, flags=0x300> > >How to make it to go into VESA mode ? How to make kernel to use Matrox >Millenium driver ? > > >The last question is about CD-ROM. Ata is working properly: > >atapci0: <Generic PCI ATA controller> port >0x2000-0x200f,0-0x3,0-0x7,0-0x3,0-0x7 irq 15 at device 20.1 on pci0 >ata0: at 0x1f0 irq 14 on atapci0 >ata1: at 0x170 irq 15 on atapci0 >[skipped] >acd0: CDROM <SAMSUNG CD-ROM SC-148C> at ata0-master PIO4 > >CD-ROM is found, but I still can not use it (mount does not work, writing: >READ_TOC command timeout - resetting >resetting devices ... done >read data overrun 12/0 > >I encountered this problem during installation, too. I was not able to >install FreeBSD from the CD the install boot from, so I installed it from >MSDOS partition (I mounted temporarily. I have only one SCSI HDD and ATA >CD-ROM in my machine. > >Why I can not use my CDROM :-( ? > >Please help, if you can :-) > >Peter Rosa _________________________________________________________________ Tired of spam? Get advanced junk mail protection with MSN 8. http://join.msn.com/?page=features/junkmail
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?Sea2-F42Y6dc6S3GE8Z00039379>