Date: Fri, 21 Jul 2000 07:00:30 -0700 (PDT) From: Sean Shilton <sean_shilton@yahoo.com> To: questions@freebsd.org Subject: ATA 66 controller only running the HD at 33MHZ Message-ID: <20000721140030.19322.qmail@web3305.mail.yahoo.com>
next in thread | raw e-mail | index | archive | help
I've got a dell dimension 550r running FreeBSD 4.0-Release. I am using vinum
to stripe two identical seagate 30GB HD's. Each HD has it's own promise ata 66
controller, yet the first drive of the stripe only runs at 33MHZ. Here's the
output from dmesg, is there anything i can do to get both drives running at
66mhz?
Thanks for any help.
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-RELEASE #0: Tue Jul 11 12:10:31 EDT 2000
root@deal.nj.sonusnet.com:/usr/src/sys/compile/NFSRAID
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium III/Pentium III Xeon (548.34-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x683 Stepping = 3
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,XMM>
real memory = 132907008 (129792K bytes)
avail memory = 125751296 (122804K bytes)
Preloaded elf kernel "kernel" at 0xc02f2000.
ccd0-3: Concatenated disk drivers
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82810E (i810E GMCH) Host To Hub bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <Intel 82810E (i810E GMCH) SVGA controller> at 1.0 irq 11
pcib1: <Intel 82801AA (ICH) Hub to PCI bridge> at device 30.0 on pci0
pci1: <PCI bus> on pcib1
fxp0: <Intel EtherExpress Pro 10/100B Ethernet> port 0xdd80-0xddbf mem
0xff700000-0xff7fffff,0xff89f000-0xff89ffff irq 10 at device 9.0 on pci1
fxp0: Ethernet address 00:d0:b7:8f:cf:72
atapci0: <Promise ATA66 controller> port
0xde80-0xdebf,0xdf98-0xdf9b,0xdf90-0xdf97,0xdf9c-0xdf9f,0xdfa0-0xdfa7 mem
0xff8a0000-0xff8bffff irq 9 at device 10.0 on pci1
ata2: at 0xdfa0 on atapci0
atapci1: <Promise ATA66 controller> port
0xdf00-0xdf3f,0xdfe0-0xdfe3,0xdfa8-0xdfaf,0xdfe4-0xdfe7,0xdff0-0xdff7 mem
0xff8e0000-0xff8fffff irq 6 at device 11.0 on pci1
ata4: at 0xdff0 on atapci1
isab0: <Intel 82801AA (ICH) PCI to LPC bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci2: <Intel ICH ATA66 controller> port 0xffa0-0xffaf at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci2
ata1: at 0x170 irq 15 on atapci2
pci0: <Intel 82801AA (ICH) USB controller> at 31.2 irq 6
pci0: <unknown card> (vendor=0x8086, dev=0x2413) at 31.3 irq 10
fdc0: cannot reserve interrupt line
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
plip0: <PLIP network interface> on ppbus0
ad0: 9765MB <Maxtor 51024U2> [19841/16/63] at ata0-master using UDMA66
ad4: 29188MB <ST330630A> [59303/16/63] at ata2-master using UDMA33
ad8: 29188MB <ST330630A> [59303/16/63] at ata4-master using UDMA66
acd0: CDROM <CRD-8480C> at ata1-master using PIO4
Mounting root from ufs:/dev/ad0s1a
vinum: loaded
vinum: reading configuration from /dev/ad8s1e
vinum: updating configuration from /dev/ad4s1e
__________________________________________________
Do You Yahoo!?
Get Yahoo! Mail – Free email you can access from anywhere!
http://mail.yahoo.com/
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20000721140030.19322.qmail>