Skip site navigation (1)Skip section navigation (2)
Date:      Sat, 23 Aug 1997 08:16:13 +0200 (MET DST)
From:      Daniel Unruh <unruh@informatik.uni-freiburg.de>
To:        aic7xxx@freebsd.org
Subject:   ``Unexpected busfree'' with 2.1.51
Message-ID:  <XFMail.970823084201.unruh@informatik.uni-freiburg.de>

next in thread | raw e-mail | index | archive | help
When booting 2.1.51, the kernel hangs during SCSI device detection:

[...]
scsi target 3 [...] refusing wide [...]
(scsi0:3:0) Reset device  active_scb 0
scsi0: (targ 3, chan A) matching scb to (targ 3/chan A)
scsi0: (targ 3, chan A) matching scb to (targ 3/chan A)
scsi0: Unexpected busfree, LASTPHASE=0xe0, SEQADDR=0x4f

Then it spews out kernel debug messages and reboots.



Hardware:  Gigabyte GA-586DX w/ onboard AIC7880.

Compile Options:
  AIC7XXX_RESET_DELAY    : 15
  AIC7XXX_TAGGED_QUEUEING: Enabled
  AIC7XXX_PAGE_ENABLE    : Enabled
  AIC7XXX_PROC_STATS     : Disabled

Adapter Configuration:
          SCSI Adapter: Adaptec AIC-7880 Ultra SCSI host adapter
                        (AIC-788x chipset)
              Host Bus: Wide
               Base IO: 0x6200
        Base IO Memory: 0xe0804000
                   IRQ: 9
                  SCBs: Used 1, HW 16, Page 255
            Interrupts: 94
         Serial EEPROM: True
  Extended Translation: Enabled
        SCSI Bus Reset: Disabled
            Ultra SCSI: Enabled
     Target Disconnect: Enabled

Attached devices: 
Host: scsi0 Channel: 00 Id: 02 Lun: 00
  Vendor: TOSHIBA  Model: CD-ROM XM-5301TA Rev: 0925
  Type:   CD-ROM                           ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 03 Lun: 00
  Vendor: SEAGATE  Model: ST43400N         Rev: 1028
  Type:   Direct-Access                    ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 04 Lun: 00
  Vendor: TANDBERG Model:  TDC 3800        Rev: =04:
  Type:   Sequential-Access                ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 05 Lun: 00
  Vendor: IMS      Model: CDD2000/00       Rev: 1.26
  Type:   CD-ROM                           ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 12 Lun: 00
  Vendor: IBM      Model: DCAS-34330W      Rev: S61A
  Type:   Direct-Access                    ANSI SCSI revision: 02



Turning on/off tagged queueing, paging and scsi bios does not help.
Disconnecting the Seagate fixes the problem.

2.0.30 runs just fine.

Is there anything I can do to get the driver running?

---------------------------------------------
  Daniel Unruh                unruh@acm.org
http://www.informatik.uni-freiburg.de/~unruh/
------m-a-i-l---f-r-o-m---B-e-r-m-u-d-a------



Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?XFMail.970823084201.unruh>