Date: Mon, 5 Feb 2007 12:25:55 +0100 From: usleepless@gmail.com To: "Simon Thoustrup" <simon@thoustrup.dk> Cc: freebsd-multimedia@freebsd.org Subject: Re: Tuner code 0x71 for Hauppauge PVR-150 (pvrxxx) Message-ID: <c39ec84c0702050325hbeaf54eu4ba7b47c2241f294@mail.gmail.com> In-Reply-To: <45C70562.5040308@thoustrup.dk> References: <45B91790.9080206@thoustrup.dk> <200701281627.23403.josh@tcbug.org> <45C60C4D.7030500@thoustrup.dk> <c39ec84c0702041403i2ad28efax51723731cc50c61e@mail.gmail.com> <45C70562.5040308@thoustrup.dk>
next in thread | previous in thread | raw e-mail | index | archive | help
Simon,
On 2/5/07, Simon Thoustrup <simon@thoustrup.dk> wrote:
> usleepless@gmail.com wrote:
> >> It takes a lot longer to load the cxm module now, but I still get:
> >>
> >> kernel: cxm0: <Conexant iTVC16 MPEG Coder> mem 0xd0000000-0xd3ffffff irq
> >> 9 at device 13.0 on pci0
> >> kernel: cxm_iic0: <Conexant iTVC15 / iTVC16 I2C controller> on cxm0
> >> kernel: iicbb0: <I2C bit-banging driver> on cxm_iic0
> >> kernel: iicbus0: <Philips I2C bus> on iicbb0 master-only
> >> kernel: tuner code 113
> >> kernel: tuner_type = 20
> >> kernel: cxm0: TCL 2002N-6A tuner
> >> kernel: <2>cxm 0-0000: loaded /lib/modules/v4l-cx25840.fw firmware
> >> (16382 bytes)
> >> kernel: <2>cxm debug 0-0000: decoder set input (0)
> >> kernel: <2>cxm debug 0-0000: now setting Tuner input
> >> kernel: <2>cxm debug 0-0000: set audio input (0)
> >> kernel: <2>cxm debug 0-0000: set audio input (0)
> >> kernel: cxm0: Eeprom PAL
> >> kernel: <2>tda 0-0000: switching to v4l2
> >> kernel: <2>tda 0-0000: configure for: PAL-BG
> >> kernel: <2>tda 0-0000: writing: b=0xd4 c=0x70 e=0x09
> >> kernel: could not start iic bus
> >> kernel: probed 54
> >> kernel: probed 136
> >> kernel: probed 160
> >> kernel: probed 194
> >> kernel: probed 224
> >> kernel: probed 226
> >> kernel: probed 228
> >> kernel: probed 230
> >> kernel: <2>tda 0-0000: i2c i/o error: rc == 2 (should be 4)
> >> kernel: read error
> >> kernel: <2>tda 0-0000: i2c i/o error: rc == -597317209 (should be 1)
> >> kernel: <2>tda 0-0000: read: 0x 0
> >> kernel: <2>tda 0-0000: after power on : no
> >> kernel: <2>tda 0-0000: afc : - 12.5 kHz
> >> kernel: <2>tda 0-0000: fmif level : low
> >> kernel: <2>tda 0-0000: afc window : out
> >> kernel: <2>tda 0-0000: vfi level : low
> >> kernel: <2>cxm 0-0000: Video signal: not present
> >> kernel: <2>cxm 0-0000: Detected format: NTSC-M
> >> kernel: <2>cxm 0-0000: Detected audio mode: forced mode
> >> kernel: <2>cxm 0-0000: Detected audio standard: forced audio standard
> >> kernel: <2>cxm 0-0000: Audio muted: no
> >> kernel: <2>cxm 0-0000: Audio microcontroller: running
> >> kernel: <2>cxm 0-0000: Configured audio standard: A2-BG
> >> kernel: <2>cxm 0-0000: Configured audio mode: undefined
> >> kernel: <2>cxm 0-0000: Specified standard: PAL-BDGHI
> >> kernel: <2>cxm 0-0000: Specified input: Tuner
> >> kernel: <2>cxm 0-0000: Specified audio input: Tuner
> >> kernel: <2>cxm 0-0000: Specified audioclock freq: 48 kHz
> >> kernel: <2>cxm 0-0000: Preferred audio mode: stereo
> >> kernel: <2>cxm 0-0000: Selected 65 MHz format: system DK
> >> kernel: <2>cxm 0-0000: Selected 45 MHz format: chroma
> >> kernel: cxm0: [GIANT-LOCKED]
> >> bsd kernel: cxm0: encoder firmware version 0x2050032
> >>
> >> - and still the same error messages when trying pvr250-setchannel:
> >>
> >> ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured
> >> ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument
> >
> > what are the exact parameters you are supplying to pvr250-setchannel?
> # pvr250-setchannel -a on -m 4 231.25
> ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured
> ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument
>
> # pvr250-setchannel -m 4 231.25
> ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured
> ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument
>
> # pvr250-setchannel 231.25
> ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured
>
>
> # pvr250-setchannel -a on -m 4 11
> ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured
> ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument
> ioctl( tfd, TVTUNER_SETCHNL ) failed.: Invalid argument
>
> # pvr250-setchannel -m 4 11
> ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured
> ioctl( tfd, TVTUNER_SETTYPE ) failed.: Invalid argument
> ioctl( tfd, TVTUNER_SETCHNL ) failed.: Invalid argument
>
> # pvr250-setchannel 11
> ioctl( tfd, BT848_GAUDIO ) failed.: Device not configured
> ioctl( tfd, TVTUNER_SETCHNL ) failed.: Invalid argument
>
> As Dan also points out in his mail, I didn't expect pvr250-setchannel to
> work as it should with the i2c bus not starting correctly, but tried it
> out in case it was just a "print-error"/warning..
well, the error messages are a bit too "serious". not all is broken.
i investigated and your tuner has is not configured for properly.
i am working on a proper fix for it at the moment, but in the meantime, you could try:
1. edit cxm_tuner.c, find "TCL 2002N-6A"
2. change "CXM_TUNER_TV_SYSTEM_MN, cxm_none_system_code_style" into:
"CXM_TUNER_TV_SYSTEM_MN | CXM_TUNER_TV_SYSTEM_BG | CXM_TUNER_TV_SYSTEM_DK, cxm_none_system_code_style"
3. recompile, reinstall and retry.
4. let me know.
regards,
usleep
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?c39ec84c0702050325hbeaf54eu4ba7b47c2241f294>