Date: Fri, 07 Jul 2000 10:23:33 -0400 From: "Andresen,Jason R." <jandrese@mitre.org> To: "freebsd-questions@FreeBSD.ORG" <freebsd-questions@FreeBSD.ORG> Subject: Wavelan card driver (wi) not even trying Message-ID: <3965E7E5.F94FA77B@mitre.org>
next in thread | raw e-mail | index | archive | help
Hi all,
I've been trying for some time now to get FreeBSD 4.0 to talk to
some Wavelan 11M Turbo Gold cards I have, which are in the ISA adaptors
on a Dell Dimention XPS P166s. When I boot the machine, neither the
pccard controller nor the wi device show on the boot messages. Not even
a "device wi0 not found".
I tried putting the if_wi_enable="YES" into the loader.conf, but that
didn't help.
I have also patched the wi device to use ALTQ, however this problem
occured before the patch.
GENERIC also fails to see either the wi or the pccard devices.
I'm including the boot messages and kernel config below. Thanks.
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
FreeBSD 4.0-RELEASE #3: Fri Jul 7 09:40:03 EDT 2000
root@hobo.nomadic.ie.org:/usr/src/sys-altq/compile/ALTQ-MITRE
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium/P54C (166.19-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x52c Stepping = 12
Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory = 33554432 (32768K bytes)
avail memory = 28819456 (28144K bytes)
Preloaded elf kernel "kernel" at 0xc03bc000.
Preloaded elf module "if_wi.ko" at 0xc03bc09c.
Intel Pentium detected, installing workaround for F00F bug
md0: Malloc disk
altq: major number is 96
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <Intel 82371SB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 ATA controller> port 0xffa0-0xffaf at device 7.1
on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <S3 ViRGE graphics accelerator> at 13.0
xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xfc80-0xfcff mem
0xffbdfc00-0xffbd
fc7f irq 10 at device 14.0 on pci0
xl0: Ethernet address: 00:50:da:bc:92:44
miibus0: <MII bus> on xl0
xlphy0: <3Com internal media interface> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: supplying EUI64: 00:50:da:ff:fe:bc:92:44
xl1: <3Com 3c905-TX Fast Etherlink XL> port 0xff00-0xff3f irq 11 at
device 15.0
on pci0
xl1: Ethernet address: 00:60:08:19:43:04
miibus1: <MII bus> on xl1
nsphy0: <DP83840 10/100 media interface> on miibus1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on
isa0
fdc0: FIFO enabled, 8 bytes threshold
atkbdc0: <keyboard controller (i8042)> at port 0x60-0x6f on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
unknown0: <WaveTable> at port 0x620-0x623 on isa0
unknown1: <Audio> at port 0x220-0x22f,0x330-0x331,0x388-0x38b irq 5 drq
1,5 on i
sa0
unknown2: <Game> at port 0x200-0x207 on isa0
ad0: 3098MB <IBM-DAQA-33240> [6296/16/63] at ata0-master using PIO4
acd0: CDROM <CD-ROM CDU311> at ata1-master using PIO3
And the kernel config (it actually ins't Generic :)
#
# GENERIC -- Generic kernel configuration file for FreeBSD/i386
#
# For more information on this file, please read the handbook section on
# Kernel Configuration Files:
#
# http://www.freebsd.org/handbook/kernelconfig-config.html
#
# The handbook is also available locally in /usr/share/doc/handbook
# if you've installed the doc distribution, otherwise always see the
# FreeBSD World Wide Web server (http://www.FreeBSD.ORG/) for the
# latest information.
#
# An exhaustive list of options and more detailed explanations of the
# device lines is also present in the ./LINT configuration file. If you
are
# in doubt as to the purpose or necessity of a line, check first in
LINT.
#
# $FreeBSD: src/sys/i386/conf/GENERIC,v 1.246 2000/03/09 16:32:55 jlemon
Exp $
machine i386
cpu I386_CPU
cpu I486_CPU
cpu I586_CPU
cpu I686_CPU
ident ALTQ-MITRE
maxusers 32
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug
symbols
options MATH_EMULATE #Support for x87 emulation
options INET #InterNETworking
options INET6 #IPv6 communications protocols
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep
this!]
options MFS #Memory Filesystem
options MD_ROOT #MD is a potential root device
options NFS #Network Filesystem
options NFS_ROOT #NFS usable as root device, NFS
required
options MSDOSFS #MSDOS Filesystem
options CD9660 #ISO 9660 Filesystem
options CD9660_ROOT #CD-ROM usable as root, CD9660
required
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP
THIS!]
options SCSI_DELAY=15000 #Delay (in ms) before probing
SCSI
options UCONSOLE #Allow users to grab the console
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time
extentions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
# To make an SMP kernel, the next two are needed
#options SMP # Symmetric MultiProcessor
Kernel
#options APIC_IO # Symmetric (APIC) I/O
# Optionally these may need tweaked, (defaults shown):
#options NCPU=2 # number of CPUs
#options NBUS=4 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
# options added for ALTQ
options NMBCLUSTERS=2048
options MROUTING # Multicast routing
#options NATM #native mode atm
# ALTQ options
options ALTQ #alternate queueing
options CBQ #class based queueing
#options WFQ #weighted fair queueing
#options FIFOQ #fifo queueing
#options RED #random early detection
#options FLOWVALVE #flowvalve for RED (needs RED)
#options RIO #twin red for diffserv (needs RED)
#options CBQ_RED #red for cbq (needs CBQ and RED)
#options CBQ_RIO #rio for cbq (needs CBQ, RIO, RED,
CBQ_RED)
#options LOCALQ #local use
#options HFSC #hierarchical fair service curve
#options HFSC_RED #red for hfsc (needs HFSC and RED)
#options HFSC_RIO #rio for hfsc (needs HFSC, RIO, RED,
HFSC_RED)
#options ALTQ_ACCOUNT #altq accounting
#options ALTQ_ECN #ecn extention to tcp
#options CDNR #diffserv traffic conditioner
#options BLUE #blue by wu-chang feng
# you might want to set kernel timer to 1kHz if you use CBQ,
# especially with 100baseT
#options HZ=1
device isa
device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
device fd1 at fdc0 drive 1
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata1 at isa? port IO_WD2 irq 15
device ata
device atadisk # ATA disk drives
device atapicd # ATAPI CDROM drives
device atapifd # ATAPI floppy drives
device atapist # ATAPI tape drives
options ATA_STATIC_ID #Static device numbering
#options ATA_ENABLE_ATAPI_DMA #Enable DMA on ATAPI devices
# SCSI Controllers
device ahb # EISA AHA1742 family
device ahc # AHA2940 and onboard AIC7xxx devices
device amd # AMD 53C974 (Teckram DC-390(T))
device dpt # DPT Smartcache - See LINT for options!
device isp # Qlogic family
device ncr # NCR/Symbios Logic
device sym # NCR/Symbios Logic (newer chipsets)
device adv0 at isa?
device adw
device bt0 at isa?
device aha0 at isa?
device aic0 at isa?
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device sa # Sequential Access (tape etc)
device cd # CD
device pass # Passthrough device (direct SCSI
access)
# RAID controllers
device ida # Compaq Smart RAID
device amr # AMI MegaRAID
device mlx # Mylex DAC960 family
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa?
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
#device vt0 at isa?
#options XSERVER # support for X server on a vt
console
#options FAT_CURSOR # start with block cursor
# If you have a ThinkPAD, uncomment this along with the rest of the PCVT
lines
#options PCVT_SCANSET=2 # IBM keyboards are non-std
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# Power management support (see LINT for more options)
device apm0 at nexus? disable flags 0x20 # Advanced Power
Management
# PCCARD (PCMCIA) support
device pcic0 at isa?
device pcic1 at isa?
device card
# You may ned to reset all pccards after resuming
# In the mid-towers, we don't suspend/resume, so we shouldn't need this
#options PCIC_RESSUME_RESET # Reset after resume
# Serial (COM) ports
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
device sio1 at isa? port IO_COM2 irq 3
device sio2 at isa? disable port IO_COM3 irq 5
device sio3 at isa? disable port IO_COM4 irq 9
# Parallel port
device ppc0 at isa? irq 7
device ppbus # Parallel port bus (required)
device lpt # Printer
device plip # TCP/IP over parallel
device ppi # Parallel port interface device
#device vpo # Requires scbus and da
# PCI Ethernet NICs.
device de # DEC/Intel DC21x4x (``Tulip'')
device fxp # Intel EtherExpress PRO/100B (82557,
82558)
device tx # SMC 9432TX (83c170 ``EPIC'')
device vx # 3Com 3c590, 3c595 (``Vortex'')
device wx # Intel Gigabit Ethernet Card
(``Wiseman'')
# PCI Ethernet NICs that use the common MII bus controller code.
device miibus # MII bus support
device dc # DEC/Intel 21143 and various workalikes
device rl # RealTek 8129/8139
device sf # Adaptec AIC-6915 (``Starfire'')
device sis # Silicon Integrated Systems SiS 900/SiS
7016
device ste # Sundance ST201 (D-Link DFE-550TX)
device tl # Texas Instruments ThunderLAN
device vr # VIA Rhine, Rhine II
device wb # Winbond W89C840F
device xl # 3Com 3c90x (``Boomerang'',
``Cyclone'')
# ISA Ethernet NICs.
device ed0 at isa? port 0x280 irq 9
#device ed1 at isa? port 0x300 irq 10
#device ex
#device ep
# WaveLAN/IEEE 802.11 wireless NICs. Note: the WaveLAN/IEEE really
# exists only as a PCMCIA device, so there is no ISA attatement needed
# and resources will always be dynamically assigned by the pccard code.
device wi
# Aironet 4500/4800 802.11 wireless NICs. Note: the declaration below
will
# work for PCMCIA and PCI cards, as well as ISA cards set to ISA PnP
# mode (the factory default). If you set the switches on your ISA
# card for a manually chosen I/O address and IRQ, you must specify
# those paremeters here.
#device an
# The probe order of these is presently determined by
i386/isa/isa_compat.c.
#device ie0 at isa? port 0x300 irq 10 iomem 0xd0000
#device fe0 at isa? port 0x300
#device le0 at isa? port 0x300 irq 5 iomem 0xd0000
#device lnc0 at isa? port 0x280 irq 10 drq 0
#device cs0 at isa? port 0x300
#device sn0 at isa? port 0x300 irq 10
# requires PCCARD (PCMCIA) support to be activated
#device xe0 at isa?
# Pseudo devices - the number indicates how many units to allocated.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device sl 1 # Kernel SLIP
pseudo-device ppp 1 # Kernel PPP
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
pseudo-device md # Memory "disks"
pseudo-device gif 4 # IPv6 and IPv4 tunneling
pseudo-device faith 1 # IPv6-to-IPv4 relaying (translation)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# USB support
#device uhci # UHCI PCI->USB interface
#device ohci # OHCI PCI->USB interface
#device usb # USB Bus (required)
#device ugen # Generic
#device uhid # "Human Interface Devices"
#device ukbd # Keyboard
#device ulpt # Printer
#device umass # Disks/Mass storage - Requires scbus
and da
#device ums # Mouse
# USB Ethernet, requires mii
#device aue # ADMtek USB ethernet
#device cue # CATC USB ethernet
#device kue # Kawasaki LSI USB ethernet
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-questions" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3965E7E5.F94FA77B>