Date: Fri, 30 Mar 2001 13:25:05 +0200 From: Andre Albsmeier <andre@akademie3000.de> To: freebsd-mobile@freebsd.org Subject: Code 136/138 not found with Xircom CM-56G Message-ID: <20010330132505.A512@schlappy.mobile.tld>
next in thread | raw e-mail | index | archive | help
Using 4.3-BETA, I get the following message when
pccardd starts up:
Code 136 not found
Code 136 not found
code Unknown ignored
Code 138 not found
Code 138 not found
code Unknown ignored
sio2 at port 0x2e8-0x2ef irq 11 slot 1 on pccard1
sio2: type 16550A
This is with a Xircom CM-56G card. The card seems to work fine
otherwise. The corresponding dumpcis command gives us:
Code 136 not found
Code 136 not found
code Unknown ignored
Code 138 not found
Code 138 not found
code Unknown ignored
Configuration data for card in slot 1
Tuple #1, code = 0x1 (Common memory descriptor), length = 2
000: 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #2, code = 0x17 (Attribute memory descriptor), length = 2
000: 00 ff
Attribute memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = reserved, 32 units
Tuple #3, code = 0x15 (Version 1 info), length = 57
000: 05 00 58 69 72 63 6f 6d 00 43 72 65 64 69 74 43
010: 61 72 64 20 4d 6f 64 65 6d 20 35 36 20 2d 20 47
020: 6c 6f 62 61 6c 41 43 43 45 53 53 00 43 4d 2d 35
030: 36 47 00 31 2e 30 30 00 ff
Version = 5.0, Manuf = [Xircom], card vers = [CreditCard Modem 56 - GlobalACCESS]
Addit. info = [CM-56G],[1.00]
Tuple #4, code = 0x0 (Null tuple), length = 8
000: 56 1b 05 00 00 00 00 00
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This is the 136 code...
Tuple #5, code = 0x20 (Manufacturer ID), length = 5
000: 05 01 0a 10 45
PCMCIA ID = 0x105, OEM ID = 0x100a
Tuple #6, code = 0x44 (Card init date), length = 4
000: ef 05 0b 27
Tuple #7, code = 0x1a (Configuration map), length = 5
000: 01 3f 80 ff 67
Reg len = 2, config register addr = 0xff80, last config = 0x3f
Registers: XXX--XX-
Tuple #8, code = 0x1b (Configuration entry), length = 20
000: e7 c1 9d 0f 55 4d 5d 26 e0 17 17 ea 60 e8 02 07
010: f0 bc 8e 20
Config index = 0x27(default)
Interface byte = 0xc1 (I/O) +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 2 x 100mA
Wait scale Speed = 1.2 x 10 ms
RDY/BSY scale Speed = 1.2 x 10 ms
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x2e8 block length = 0x8
IRQ modes: Level, Pulse, Shared
IRQs: 2 3 4 5 7 9 10 11 15
Max twin cards = 0
Misc attr: (Power down supported)
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 1f 08 ea 60 e8 03 07
Config index = 0x1f
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x3e8 block length = 0x8
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 17 08 ea 60 f8 02 07
Config index = 0x17
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x2f8 block length = 0x8
Tuple #11, code = 0x1b (Configuration entry), length = 7
000: 0f 08 ea 60 f8 03 07
Config index = 0xf
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x3f8 block length = 0x8
Tuple #12, code = 0x1b (Configuration entry), length = 3
000: 3f 08 63
Config index = 0x3f
Card decodes 3 address lines, full 8/16 Bit I/O
Tuple #13, code = 0x21 (Functional ID), length = 2
000: 02 00
Serial port/modem
Tuple #14, code = 0x22 (Functional EXT), length = 4
000: 00 02 0f 5c
Serial interface extension:
16550 UART, Parity - Space,Mark,Odd,Even
Data bit - 7bit,8bit, Stop bit - 1bit,2bit
Tuple #15, code = 0x22 (Functional EXT), length = 12
000: 02 06 00 3f 1c 03 03 0f 07 00 01 b5
Data modem services available:
Tuple #16, code = 0x22 (Functional EXT), length = 8
000: 13 06 00 00 00 00 00 00
Fax1/modem services available:
Tuple #17, code = 0x0 (Null tuple), length = 12
000: 39 41 30 30 44 43 30 35 31 42 35 36
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This is the 138 code...
Tuple #18, code = 0x14 (No link), length = 0
Tuple #19, code = 0xff (Terminator), length = 0
2 slots found
Anything wrong here? Or should I simply ignore it? I have seen
similar messages when using a Intel EtherExpress(TM) PRO/100 PC
Card Mobile Adapter16...
Thanks,
-Andre
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-mobile" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20010330132505.A512>