Date: Fri, 31 Oct 2003 20:09:05 +0100 From: Jonas Sonntag <jonas.sonntag@jbhosting.de> To: Jonas Sonntag <jonas.sonntag@jbhosting.de> Cc: freebsd-questions@freebsd.org Subject: Re: vinum on atapi raid Message-ID: <3FA2B351.9050407@jbhosting.de> In-Reply-To: <3FA19C72.2050607@jbhosting.de> References: <3FA19C72.2050607@jbhosting.de>
next in thread | previous in thread | raw e-mail | index | archive | help
hi again just for the record: this really seems to be an issue with the ar device. i took one of the drives off from the promise controller (ar), attached it to the onboard controller (ad) and everything works fine. i'm cc'ing to freebsd-hackers because of this post: http://www.geocrawler.com/mail/msg.php3?msg_id=6949487&list=159 (see below). now, another question: looking at dmesg i found that ar2 is also given the device name ad7 (don't be confused by my previous post, the order of the disks changed): ar2: 117246MB <ATA RAID0 array> [14946/255/63] status: READY subdisks: 0 READY ad7: 117246MB <Maxtor 6Y120L0> [238216/16/63] at ata3-slave UDMA100 so i though i might use ad7 instead of ar2 but trying to use /dev/ad7 with disklabel gives me 'Device is busy' error. please note that this is in fact no raid configuration. the disks just appear as ar because they are attached to the promise controller. hum... again, any hints how i could build a concatenated vinum volume from the single ar drives ? thanks and br, jonas Jonas Sonntag wrote: > hi list > > i'm trying to set up a concatenated vinum volume. i read chapter 13 in > the handbook and as so often i've found a nice how-to on > freebsddiary.org but somehow i'm stuck. > > my /etc/vinum.conf file is like this: > drive a device /dev/ar1h > drive b device /dev/ar2h > volume stuff > plex org concat > sd length 117239m drive a > sd length 78528m drive b > > > disklabels: > # /dev/ar1c: > type: ESDI > disk: ar1s1 > label: > flags: > bytes/sector: 512 > sectors/track: 63 > tracks/cylinder: 255 > sectors/cylinder: 16065 > cylinders: 14945 > sectors/unit: 240107427 > rpm: 3600 > interleave: 1 > trackskew: 0 > cylinderskew: 0 > headswitch: 0 # milliseconds > track-to-track seek: 0 # milliseconds > drivedata: 0 > > 8 partitions: > # size offset fstype [fsize bsize bps/cpg] > c: 240107427 0 unused 0 0 # (Cyl. 0 - > 14945*) > h: 240107427 0 vinum # (Cyl. 0 - > 14945*) > > # /dev/ar2c: > type: ESDI > disk: ar2s1 > label: > flags: > bytes/sector: 512 > sectors/track: 63 > tracks/cylinder: 255 > sectors/cylinder: 16065 > cylinders: 10010 > sectors/unit: 160826652 > rpm: 3600 > interleave: 1 > trackskew: 0 > cylinderskew: 0 > headswitch: 0 # milliseconds > track-to-track seek: 0 # milliseconds > drivedata: 0 > > 8 partitions: > # size offset fstype [fsize bsize bps/cpg] > c: 160826652 0 unused 0 0 # (Cyl. 0 - > 10010*) > h: 160826652 0 vinum # (Cyl. 0 - > 10010*) > > > fidsk also looks good: > > /dev/ar1: > The data for partition 1 is: > sysid 165,(FreeBSD/NetBSD/386BSD) > start 63, size 240107427 (117239 Meg), flag 80 (active) > beg: cyl 0/ head 1/ sector 1; > end: cyl 1023/ head 254/ sector 63 > > /dev/ar2: > The data for partition 1 is: > sysid 165,(FreeBSD/NetBSD/386BSD) > start 63, size 160826652 (78528 Meg), flag 80 (active) > beg: cyl 0/ head 1/ sector 1; > end: cyl 1023/ head 254/ sector 63 > > > now i seem to be missing something here.. when i do > vinum create -f /etc/vinum.conf > > what i get is: > > 1: drive a device /dev/ar1h > ** 1 Can't initialize drive a: Operation not supported by device > 2: drive b device /dev/ar2h > ** 2 Can't initialize drive b: Operation not supported by device > 0 drives: > 1 volumes: > V stuff State: down Plexes: 1 Size: > 191 GB > > 1 plexes: > P stuff.p0 C State: faulty Subdisks: 2 Size: > 191 GB > > 2 subdisks: > S stuff.p0.s0 State: crashed PO: 0 B Size: > 114 GB > S stuff.p0.s1 State: crashed PO: 114 GB Size: > 76 GB > > messages says: > /kernel: vinum: stuff.p0.s0 is crashed > /kernel: vinum: stuff.p0 is faulty > /kernel: vinum: stuff.p0.s1 is crashed > > > i have 'obliterated' the volume, i have remade the devices i allways > end up with "Operation not supported by device". > > something similar happens when i'm using the concat command to vinum: > vinum -> concat -v /dev/ar1h /dev/ar2h > volume vinum0 > plex name vinum0.p0 org concat > drive vinumdrive0 device /dev/ar1h > Can't create drive vinumdrive0, device /dev/ar1h: Can't initialize > drive vinumdrive0 > > i have come across this post: > http://www.geocrawler.com/mail/msg.php3?msg_id=6949487&list=159 > could that be the case with /dev/ar, too? i'm on 4.8-stable. > > any hints how to go on would be great. please cc me, as i'm not on the > list. > > thanks and br > jonas >
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?3FA2B351.9050407>