Skip site navigation (1)Skip section navigation (2)
Date:      Thu, 1 Jan 2015 15:15:29 -0800
From:      Thomas Skibo <thomasskibo@sbcglobal.net>
To:        Adrian Chadd <adrian@freebsd.org>
Cc:        "freebsd-arm@freebsd.org" <freebsd-arm@freebsd.org>
Subject:   Re: FreeBSD 11-CURRENT image does not boot on the Raspberry PI B
Message-ID:  <7959322F-CE0A-4516-BC68-CE4D3534DD6B@sbcglobal.net>
In-Reply-To: <CAJ-VmokhSGFNbCs-ayH943sh4wRxHsGJbp-3Yp5bYUmTdBRP=A@mail.gmail.com>
References:  <CAM=N1ucDYkmhCyaw_n%2Bqv_xx%2BTwbksK9ndp0O4PET%2BnjMc13tQ@mail.gmail.com> <CAJ-VmokhSGFNbCs-ayH943sh4wRxHsGJbp-3Yp5bYUmTdBRP=A@mail.gmail.com>

next in thread | previous in thread | raw e-mail | index | archive | help


> On Jan 1, 2015, at 2:30 PM, Adrian Chadd <adrian@freebsd.org> wrote:
>=20
> hi!
>=20
> can you plug in a serial UART and see if anything else gets spat out =
there?
>=20
>=20
>=20
> -adrian
>=20
>=20

I think I am having the same problem.  Here=E2=80=99s the UART output:



U-Boot 2013.01-rc1-svn18531 (Dec 24 2014 - 16:51:42)

DRAM:  480 MiB
WARNING: Caches not enabled
MMC:   bcm2835_sdhci: 0
Using default environment

In:    serial
Out:   lcd
Err:   lcd
mbox: Timeout waiting for response
bcm2835: Could not set USB power state
Net:   Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot:  0=20
reading uEnv.txt
89 bytes read in 8959 ms (0 Bytes/s)
Importing environment from mmc ...
reading ubldr
251119 bytes read in 56398 ms (3.9 KiB/s)
## Starting application at 0x02000054 ...
Consoles: U-Boot console =20
Compatible U-Boot API signature found @1db682a8

FreeBSD/armv6 U-Boot loader, Revision 1.2
(root@grind.freebsd.org, Wed Dec 24 16:51:33 UTC 2014)

DRAM: 480MB
Number of U-Boot devices: 1
U-Boot env: loaderdev not set, will probe all devices.
Found U-Boot device: disk
  Probing all disk devices...
  Checking unit=3D0 slice=3D<auto> partition=3D<auto>... good.
Loading /boot/defaults/loader.conf=20
/boot/kernel/kernel data=3D0x4f54a4+0xb6b5c =
syms=3D[0x4+0x8cbd0+0x4+0x53f47]

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel] in 5 seconds... Booting =
[/boot/kernel/kernel] in 1 second... Booting [/boot/kernel/kernel]...    =
          =20
Using DTB provided by U-Boot at address 0x100.
Kernel entry at 0x100100...
Kernel args: (null)
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2014 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights =
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #0 r276066: Wed Dec 24 16:49:32 UTC 2014
    root@grind.freebsd.org:/usr/obj/arm.armv6/usr/src/sys/RPI-B arm
FreeBSD clang version 3.4.1 (tags/RELEASE_34/dot1-final 208032) 20140512
VT: init without driver.
CPU: ARM1176JZ-S rev 7 (ARM11J core)
 Supported features: ARM_ISA THUMB2 JAZELLE ARMv4 Security_Ext
 WB enabled LABT branch prediction enabled
  16KB/32B 4-way instruction cache
  16KB/32B 4-way write-back-locking-C data cache
real memory  =3D 536866816 (511 MB)
avail memory =3D 483196928 (460 MB)
random device not loaded/active; using insecure pseudo-random number =
generator
random: entropy device infrastructure driver
random: selecting highest priority adaptor <Dummy>
random: SOFT: yarrow init()
random: selecting highest priority adaptor <Yarrow>
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> mem 0x20000000-0x20ffffff =
on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
bcm2835_cpufreq0: <CPU Frequency Control> on cpu0
intc0: <BCM2835 Interrupt Controller> mem 0xb200-0xb3ff on simplebus0
systimer0: <BCM2835 System Timer> mem 0x3000-0x3fff irq 8,9,10,11 on =
simplebus0
Event timer "BCM2835 Event Timer 3" frequency 1000000 Hz quality 1000
Timecounter "BCM2835 Timecounter" frequency 1000000 Hz quality 1000
bcmwd0: <BCM2708/2835 Watchdog> mem 0x10001c-0x100027 on simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x200000-0x2000af irq =
57,59,58,60 on simplebus0
gpio0: read-only pins: 46,47,48,49,50,51,52,53.
gpio0: reserved pins: 48,49,50,51,52,53.
gpioc0: <GPIO controller> on gpio0
gpiobus0: <OFW GPIO bus> on gpio0
gpioled0: <GPIO led> at pin(s) 16 on gpiobus0
iichb0: <BCM2708/2835 BSC controller> mem 0x205000-0x20501f irq 61 on =
simplebus0
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <BCM2708/2835 BSC controller> mem 0x804000-0x80401f irq 61 on =
simplebus0
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
spi0: <BCM2708/2835 SPI controller> mem 0x204000-0x20401f irq 62 on =
simplebus0
spibus0: <OFW SPI bus> on spi0
bcm_dma0: <BCM2835 DMA Controller> mem 0x7000-0x7fff,0xe05000-0xe05fff =
irq 24,25,26,27,28,29,30,31,32,33,34,35,36 on simplebus0
mbox0: <BCM2835 VideoCore Mailbox> mem 0xb880-0xb8bf irq 1 on simplebus0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x300000-0x3000ff irq =
70 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
uart0: <PrimeCell UART (PL011)> mem 0x201000-0x201fff irq 65 on =
simplebus0
uart0: console (115200,n,8,1)
dwcotg0: <DWC OTG 2.0 integrated USB controller> mem 0x980000-0x99ffff =
irq 17 on simplebus0
usbus0 on dwcotg0
fb0: <BCM2835 VT framebuffer driver> on ofwbus0
Timecounters tick every 10.000 msec
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get clock rate (id=3D3)
usbus0: 480Mbps High Speed USB v2.0
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get clock rate (id=3D8)
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get min clock rate (id=3D3)
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get min clock rate (id=3D4)
ugen0.1: <DWCOTG> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get min clock rate (id=3D8)
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get max voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get min voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get max voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get max voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get max voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get min voltage
bcm2835_cpufreq0: mbox response error
bcm2835_cpufreq0: can't get min voltage
bcm2835_cpufreq0: ARM -999MHz, Core 250MHz, SDRAM -999MHz, Turbo OFF
bcm2835_cpufr


=E2=80=94=E2=80=94=E2=80=94
Thomas Skibo
thomasskibo@sbcglobal.net




Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?7959322F-CE0A-4516-BC68-CE4D3534DD6B>