Date: Sat, 4 Jan 2003 22:49:32 -0500 From: Rahul Siddharthan <rsidd@online.fr> To: Craig Rodrigues <rodrigc@attbi.com> Cc: current@freebsd.org Subject: Re: Unable to mount ext2fs partition Message-ID: <20030105034932.GA65111@papagena.rockefeller.edu> In-Reply-To: <20030105034150.GA995@attbi.com> References: <20030105022547.GA40477@papagena.rockefeller.edu> <20030105025059.GA761@papagena.rockefeller.edu> <20030105034150.GA995@attbi.com>
next in thread | previous in thread | raw e-mail | index | archive | help
Craig Rodrigues said on Jan 4, 2003 at 22:41:50:
>
> You truncated too much stuff, can you repost the whole dmesg output,
> not just the parts you think are relevant.
OK, here it is at the bottom.
> Also, what do you get when you do the following:
>
> file - < /dev/ad0s1a
standard input: x86 boot sector, system, BSD disklabel
> file - < /dev/ad0s1b
standard input: Unix Fast File system (little-endian), last mounted on /usr2, last written at Fri Jan 11 13:34:17 2002, clean flag 1, number of blocks 6853713, number of data blocks 6642013, number of cylinder groups 210, block size 8192, fragment size 1024, minimum percentage of free blocks 8, rotational delay 0ms, disk rotational speed 60rps, TIME optimization
> file - < /dev/ad0s1c
standard input: x86 boot sector, system, BSD disklabel
> file - < /dev/ad0s1e
standard input: Unix Fast File system (little-endian), last mounted on /usr, last written at Sat Jan 4 22:46:06 2003, clean flag 0, number of blocks 6657105, number of data blocks 6451453, number of cylinder groups 204, block size 8192, fragment size 1024, minimum percentage of free blocks 8, rotational delay 0ms, disk rotational speed 60rps, TIME optimization
And for file - < /dev/ad0s2, it gives
standard input: x86 boot sector, BSD disklabel
HTH
- Rahul
---
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.0-CURRENT #0: Sat Jan 4 13:49:25 EST 2003
root@bluerondo.a.la.turk:/usr/obj/usr/src/sys/BLUERONDO_CURRENT
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0540000.
Preloaded elf module "/boot/kernel/acpi.ko" at 0xc05400a8.
Calibrating clock(s) ... TSC clock: 799980311 Hz, i8254 clock: 1193294 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 799914775 Hz
CPU: Pentium III/Pentium III Xeon/Celeron (799.91-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x686 Stepping = 6
Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory = 129957888 (123 MB)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x00567000 - 0x07be7fff, 124260352 bytes (30337 pages)
avail memory = 120438784 (114 MB)
bios32: Found BIOS32 Service Directory header at 0xc00f74f0
bios32: Entry = 0xfd720 (c00fd720) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xfd720+0x11e
pnpbios: Found PnP BIOS data at 0xc00f7540
pnpbios: Entry = f0000:a2f9 Rev = 1.0
pnpbios: OEM ID 1500110e
Other BIOS signatures found:
Initializing GEOMetry subsystem
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <PTLTD RSDT > on motherboard
ACPI-0625: *** Info: GPE Block0 defined as GPE0 to GPE15
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=06011106)
Using $PIR table, 5 entries at 0xc00fdf70
PCI-Only Interrupts: none
Location Bus Device Pin Link IRQs
embedded 0 9 A 0x02 11
embedded 0 9 B 0x03 9
embedded 0 11 A 0x05 11
embedded 0 7 A 0x01 9
embedded 0 7 B 0x02 11
embedded 0 7 C 0x03 9
embedded 0 7 D 0x05 11
embedded 0 1 A 0x01 9
acpi0: power button is handled as a fixed feature programming model.
ACPI timer looks BAD min = 1, max = 6, width = 6
ACPI timer looks GOOD min = 1, max = 2, width = 2
ACPI timer looks GOOD min = 1, max = 3, width = 3
ACPI timer looks GOOD min = 1, max = 2, width = 2
ACPI timer looks GOOD min = 1, max = 2, width = 2
ACPI timer looks GOOD min = 1, max = 2, width = 2
ACPI timer looks GOOD min = 1, max = 2, width = 2
ACPI timer looks GOOD min = 1, max = 2, width = 2
ACPI timer looks GOOD min = 1, max = 2, width = 2
ACPI timer looks GOOD min = 1, max = 2, width = 2
Timecounter "ACPI-safe" frequency 3579545 Hz
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0
acpi_cpu0: <CPU> on acpi0
acpi_tz0: <thermal zone> on acpi0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
acpi_acad0: <AC adapter> on acpi0
acpi_cmbat0: <Control method Battery> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
\\_SB_.PCI0.PIB_.LNKA irq 9: [ 9 11 12] low,level,sharable 0.1.0
\\_SB_.PCI0.PIB_.LNKA irq 9: [ 9 11 12] low,level,sharable 0.7.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 9 11 12] low,level,sharable 0.7.1
\\_SB_.PCI0.PIB_.LNKC irq 9: [ 9 11 12] low,level,sharable 0.7.2
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 9 11 12] low,level,sharable 0.7.3
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 9 11 12] low,level,sharable 0.11.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 9 11 12] low,level,sharable 0.9.0
\\_SB_.PCI0.PIB_.LNKC irq 9: [ 9 11 12] low,level,sharable 0.9.1
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
\\_SB_.PCI0.PIB_.LNKA irq 9: [ 9 11 12] low,level,sharable 0.1.0
\\_SB_.PCI0.PIB_.LNKA irq 9: [ 9 11 12] low,level,sharable 0.7.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 9 11 12] low,level,sharable 0.7.1
\\_SB_.PCI0.PIB_.LNKC irq 9: [ 9 11 12] low,level,sharable 0.7.2
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 9 11 12] low,level,sharable 0.7.3
\\_SB_.PCI0.PIB_.LNKD irq 11: [ 9 11 12] low,level,sharable 0.11.0
\\_SB_.PCI0.PIB_.LNKB irq 11: [ 9 11 12] low,level,sharable 0.9.0
\\_SB_.PCI0.PIB_.LNKC irq 9: [ 9 11 12] low,level,sharable 0.9.1
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base f8000000, size 26, enabled
found-> vendor=0x1106, dev=0x0601, revid=0x05
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0xa290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x8601, revid=0x00
bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0xa230, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0686, revid=0x22
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x0087, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 00001420, size 4, enabled
found-> vendor=0x1106, dev=0x0571, revid=0x10
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[20]: type 4, range 32, base 00001400, size 5, enabled
found-> vendor=0x1106, dev=0x3038, revid=0x10
bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0013, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
powerspec 2 supports D0 D3 current D0
found-> vendor=0x1106, dev=0x3057, revid=0x30
bus=0, slot=7, func=4
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 4, range 32, base 00001000, size 8, enabled
map[14]: type 4, range 32, base 00001434, size 2, enabled
map[18]: type 4, range 32, base 00001430, size 2, enabled
found-> vendor=0x1106, dev=0x3058, revid=0x20
bus=0, slot=7, func=5
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=c, irq=9
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base f4000000, size 16, enabled
map[14]: type 4, range 32, base 00001438, size 3, enabled
found-> vendor=0x14f1, dev=0x2013, revid=0x01
bus=0, slot=9, func=0
class=07-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0003, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
found-> vendor=0x104c, dev=0xac50, revid=0x01
bus=0, slot=11, func=0
class=06-07-00, hdrtype=0x02, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0xc0 (48000 ns), maxlat=0x03 (750 ns)
intpin=a, irq=255
powerspec 1 supports D0 D1 D2 D3 current D0
agp0: <VIA Generic host to PCI bridge> mem 0xf8000000-0xfbffffff at device 0.0 on pci0
agp0: allocating GATT for aperture of size 256M
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xf000-0xfff
pcib1: memory decode 0xf4100000-0xf57fffff
pcib1: prefetched decode 0xfff00000-0xfffff
pcib1: could not get PCI interrupt routing table for \\_SB_.PCI0.AGP_ - AE_NOT_FOUND
pci1: <ACPI PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 1, range 32, base f5000000, size 23, enabled
map[14]: type 1, range 32, base f4100000, size 17, enabled
map[18]: type 1, range 32, base f4800000, size 23, enabled
found-> vendor=0x1023, dev=0x8520, revid=0x6a
bus=1, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0203, statreg=0x02b0, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=9
powerspec 1 supports D0 D1 D2 D3 current D0
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA66 controller> port 0x1420-0x142f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1420
ata0: mask=03 ostat0=50 ostat2=00
ata0-slave: ATAPI 00 00
ata0-master: ATAPI 00 00
ata0: mask=03 stat0=50 stat1=50
ata0-master: ATA 01 a5
ata0: devices=01
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1428
ata1: mask=03 ostat0=50 ostat2=01
ata1-master: ATAPI 14 eb
ata1-slave: ATAPI 00 00
ata1: mask=03 stat0=00 stat1=01
ata1-slave: ATA 24 a5
ata1: devices=06
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0x1400-0x141f irq 11 at device 7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.4 (no driver attached)
pcm0: <VIA VT82C686A> port 0x1430-0x1433,0x1434-0x1437,0x1000-0x10ff irq 9 at device 7.5 on pci0
pcm0: ac97 codec id 0x41445348 (Analog Devices AD1881A)
pcm0: ac97 codec features headphone, 6 bit master volume, Analog Devices Phat Stereo
pcm0: ac97 primary codec extended features variable rate PCM
pcm0: sndbuf_setmap 6b9000, 1000; 0xc2305000 -> 6b9000
pcm0: sndbuf_setmap 717000, 1000; 0xc2303000 -> 717000
pci0: <simple comms> at device 9.0 (no driver attached)
pcib0: matched entry for 0.11.INTA (source \\_SB_.PCI0.PIB_.LNKD)
pcib0: slot 11 INTA is routed to irq 11
pcic0: <TI PCI-1410 PCI-CardBus Bridge> irq 11 at device 11.0 on pci0
pcic0: PCI Memory allocated: 0x88000000
pcic0: TI12XX PCI Config Reg: [ring enable][speaker enable][pwr save][CSC serial isa irq]
pcic0: PCI Configuration space:
0x00: 0xac50104c 0x02100007 0x06070001 0x00022000
0x10: 0x88000000 0x020000a0 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x0760010b
0x40: 0xb1030e11 0x00000001 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0xc0449061 0x00000000 0x00000000 0x00001002
0x90: 0x616482c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe110001 0x00c00100 0x00000000 0x0000001f
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
pccard0: <PC Card 16-bit bus (classic)> on pcic0
psmcpnp0 irq 12 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 2 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
unknown: not probed (disabled)
unknown: not probed (disabled)
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 1 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
plip0: <PLIP network interface> on ppbus0
lp0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
acpi_ec0: <embedded controller> port 0x66,0x62 on acpi0
unknown: not probed (disabled)
unknown: not probed (disabled)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
pcic: pcic0 already exists; skipping it
ppc: ppc0 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROM> at iomem 0xc0000-0xcbfff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0x1 0x1 0x1 0x1
sio0: probe failed test(s): 0 1 2 4 6 7 9
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250 or not responding
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0x1 0x1 0x1 0x1
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 6b 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 6b 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounters tick every 10.000 msec
lo0: bpf attached
acpi_acad0: acline initialization start
acpi_acad0: On Line
acpi_acad0: acline initialization done, tried 1 times
acpi_cmbat0: battery initialization start
acpi_cmbat0: battery initialization done, tried 1 times
ata1-slave: timeout waiting for interrupt
ata1-slave: ATA identify failed
ad0: success setting UDMA4 on VIA chip
GEOM: new disk ad0
ar: FreeBSD check1 failed
ad0: <TOSHIBA MK1517GAP/A1.04 H> ATA-5 disk at ata0-master
ad0: 9590MB (19640880 sectors), 19485 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA66
ad0: piomode=4 dmamode=2 udmamode=5 cblid=1
ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata1-master: success setting UDMA2 on VIA chip
acd0: <LG DVD-ROM DRN-8080B/3.10> DVD-ROM drive at ata1 as master
acd0: 512KB buffer, UDMA33
acd0: Reads: CD-R, CD-RW, CD-DA stream, DVD-ROM, DVD-R, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
GEOM: Configure ad0s1, start 32256 length 7123060224 end 7123092479
GEOM: Configure ad0s2, start 7123092480 length 2928199680 end 10051292159
GEOM: Add ad0s1 hot[0] start 512 length 276 end 787
GEOM: Configure ad0s1a, start 0 length 104857600 end 104857599
GEOM: Configure ad0s1b, start 104857600 length 201326592 end 306184191
GEOM: Configure ad0s1c, start 0 length 7123060224 end 7123060223
GEOM: Configure ad0s1e, start 306184192 length 6816876032 end 7123060223
Mounting root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
Linux ELF exec handler installed
linprocfs registered
acpi_acad0: Notify 0
pcic0: Event mask 0x4
pcic0: Event mask 0x4
pcic0: Event mask 0x6
pcic0: Autodetected 5.0V card
pccard: card inserted, slot 0
pcic0: reset 1 int is 10 stat is 4f
pcic0: reset 2 int is 70 stat is 4f
pcic0: Event mask 0x9
pcic0: reset 3 int is 70 stat is 6f
pccard0: Assigning ed1: io 0x300-0x31f irq 11 flags 0x80000
pcic: I/O win 0 flags 15 300-31f
ed1: Forcing IRQ to 11
pcic: I/O win 0 flags 5 300-31f
ed1 at port 0x300-0x31f irq 11 flags 0x80000 slot 0 on pccard0
pcic: I/O win 0 flags 15 300-31f
ed1: Forcing IRQ to 11
ed1: bpf attached
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-current" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20030105034932.GA65111>