Date: Thu, 07 Mar 2024 07:26:05 +0000 From: bugzilla-noreply@freebsd.org To: wireless@FreeBSD.org Subject: [Bug 272732] hostapd error with rtwn0: MAC/BB RTL8192EU, RF 6052 2T2R Message-ID: <bug-272732-21060-rRtzUpu3l7@https.bugs.freebsd.org/bugzilla/> In-Reply-To: <bug-272732-21060@https.bugs.freebsd.org/bugzilla/> References: <bug-272732-21060@https.bugs.freebsd.org/bugzilla/>
next in thread | previous in thread | raw e-mail | index | archive | help
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=3D272732 --- Comment #8 from St=C3=A9phane Rochoy <stephane.rochoy@stormshield.eu> -= -- I upgraded (using handbook's procedure[1]) to latest stable/13, namely 8c6964b779ce (2024-03-05 00:18:58 +0000) and didn't notice any improvement.= =20 [1] https://docs.freebsd.org/en/books/handbook/cutting-edge/ When the hardware is plugged, its LED start to blink and here's what writte= n to msgbuf: rtwn0 on uhub2 rtwn0: <802.11n NIC > on usbus2 rtwn0: MAC/BB RTL8192EU, RF 6052 2T2R rtwn0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps rtwn0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mb= ps 36Mbps 48Mbps 54Mbps rtwn0: 2T2R rtwn0: 11ng MCS 20MHz rtwn0: MCS 0-7: 6.5Mbps - 65Mbps rtwn0: MCS 8-15: 13Mbps - 130Mbps rtwn0: 11ng MCS 20MHz SGI rtwn0: MCS 0-7: 7Mbps - 72Mbps rtwn0: MCS 8-15: 14.5Mbps - 144.5Mbps wlan0: bpf attached wlan0: Ethernet address: 28:87:ba:77:e2:0c firmware: 'rtwn-rtl8192eufw' version 111: 31818 bytes loaded at 0xffffffff82ef7000 pflog0: bpf attached pflog0: promiscuous mode enabled rtwn0: rtwn_tx_beacon_check: cannot push beacon into chip, error 60! rtwn0: unable to push beacon into the chip, error 60 rtwn0: rtwn_newstate: could not move to RUN state and here's what `ifconfig wlan0` say: wlan0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 15= 00 ether 28:87:ba:77:e2:0c inet 172.28.199.56 netmask 0xfffc0000 broadcast 172.31.255.255 groups: wlan ssid Hu0eenee channel 10 (2457 MHz 11g ht/20) bssid 28:87:ba:77:e2:= 0c regdomain ETSI country FR authmode OPEN privacy OFF txpower 30 scanvalid 60 protmode CTS ht20 ampdulimit 64k ampdudensity 16 short= gi -stbc -ldpc -uapsd wme dtimperiod 1 -dfs parent interface: rtwn0 media: IEEE 802.11 Wireless Ethernet autoselect mode 11ng <hostap> status: running nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> As vendor and product IDs cannot be seen in msgbuf, here's content of the `dev.rtwn.0` sysctl node: dev.rtwn.0.rx_buf_size: 24 dev.rtwn.0.ratectl_selected: 1 dev.rtwn.0.ratectl: 1 dev.rtwn.0.hwcrypto: 1 dev.rtwn.0.debug: 0 dev.rtwn.0.ht40: 0 dev.rtwn.0.%parent: uhub1 dev.rtwn.0.%pnpinfo: vendor=3D0x2357 product=3D0x0109 devclass=3D0x00 devsubclass=3D0x00 devproto=3D0x00 sernum=3D"00e04c000001" release=3D0x0200= mode=3Dhost intclass=3D0xff intsubclass=3D0xff intprotocol=3D0xff dev.rtwn.0.%location: bus=3D2 hubaddr=3D1 port=3D4 devaddr=3D4 interface=3D= 0 ugen=3Dugen2.4 dev.rtwn.0.%driver: rtwn dev.rtwn.0.%desc: 802.11n NIC My /etc/hostapd.conf is as follow: debug=3D2 accept_mac_file=3D/etc/hostapd.accept ap_isolate=3D1 auth_algs=3D3 #channel=3D0 ctrl_interface=3D/var/run/hostapd #driver=3Dbsd hw_mode=3Dg #ignore_broadcast_ssid=3D0 interface=3Dwlan0 macaddr_acl=3D1 wpa=3D2 wpa_pairwise=3DCCMP wpa_passphrase=3DPASSWORD wpa_key_mgmt=3DWPA-PSK (I tried to be clever by adding `debug=3D2` to later discover it is depreca= ted x_x) And here's what happen when I `service start hostapd`: Starting hostapd. Configuration file: /etc/hostapd.conf Line 2: DEPRECATED: 'debug' configuration variable is not used anymore bsd_ctrl_iface: if wlan0 (changed) enable 0 IFF_UP 0 BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits) Completing interface initialization hostapd_setup_bss(hapd=3D0x16dc9433f000 (wlan0), first=3D1) bsd_set_privacy: enabled=3D0 bsd_set_key: alg=3D0 addr=3D0x0 key_idx=3D0 set_tx=3D0 seq_len=3D0 key_len= =3D0 bsd_del_key: key_idx=3D0 bsd_set_key: alg=3D0 addr=3D0x0 key_idx=3D1 set_tx=3D0 seq_len=3D0 key_len= =3D0 bsd_del_key: key_idx=3D1 bsd_set_key: alg=3D0 addr=3D0x0 key_idx=3D2 set_tx=3D0 seq_len=3D0 key_len= =3D0 bsd_del_key: key_idx=3D2 bsd_set_key: alg=3D0 addr=3D0x0 key_idx=3D3 set_tx=3D0 seq_len=3D0 key_len= =3D0 bsd_del_key: key_idx=3D3 Using interface wlan0 with hwaddr 28:87:ba:77:e2:0c and ssid "Hu0eenee" Deriving WPA PSK based on passphrase SSID - hexdump_ascii(len=3D8): 48 75 30 65 65 6e 65 65 PSK (ASCII passphrase) - hexdump_ascii(len=3D8) [REMOVED] PSK (from passphrase) - hexdump_ascii(len=3D32) [REMOVED] bsd_set_ieee8021x: enabled=3D1 bsd_configure_wpa: enable WPA=3D 0x2 >From here, the LED on the device is OFF and there's a delay of ~30 seconds before: =E2=80=A6 Could not remove generic information element from interface wlan0 bsd_set_ieee8021x: enabled=3D0 ioctl[SIOCS80211, op=3D7, val=3D4, arg_len=3D0]: Network is down Interface initialization failed wlan0: interface state UNINITIALIZED->DISABLED wlan0: AP-DISABLED wlan0: Unable to setup interface. =E2=80=A6 (I transcribed most of the messages from a screenshot, I didn't investigate= the reason why all this messages were not part of /var/log/daemon.log or /var/log/debug.log) I didn't have time to install net/hostapd. I'll try that today or tomorrow. --=20 You are receiving this mail because: You are the assignee for the bug.=
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?bug-272732-21060-rRtzUpu3l7>