Date: Thu, 31 Mar 2016 01:11:45 -0500 From: Erik Moe <e.moe@rcn.com> To: Daniel Braniss <danny@cs.huji.ac.il> Cc: freebsd-arm <freeBSD-arm@freebsd.org> Subject: Re: Odroidc1+ stuck booting Message-ID: <B39CD871-7BE5-44EA-816A-42A80E34D8A7@rcn.com> In-Reply-To: <982FE02C-7BEC-4CA0-BCAE-FE6CC5C9CFB4@rcn.com> References: <687E2129-BE66-4CC9-9B30-D8DFB7A2FEF6@cs.huji.ac.il> <982FE02C-7BEC-4CA0-BCAE-FE6CC5C9CFB4@rcn.com>
next in thread | previous in thread | raw e-mail | index | archive | help
I built a new image for my odriod-c1 for ssd from the latest sources and =
had no issues and didn=E2=80=99t need to tweet anything. I don=E2=80=99t =
have and odriod-c1+, but my understanding is there isn=E2=80=99t much =
difference between the two. I am using the serial console.
=
QA5:A;SVN:B72;POC:17F;STS:0;BOOT:0;INIT:10;BOOT:1;INIT:0;READ:0;CHECK:0;PA=
SS:1;
-----------------------------------------------------------------------
* Welcome to Hardkernel's ODROID-C... (Built at 19:33:00 Dec 8 2014) *
-----------------------------------------------------------------------
CPU : AMLogic S805
MEM : 1024MB (DDR3@792MHz)
BID : HKC13C0001
S/N : HKC1CC037EBE4620
0x0000009f
check SD_boot_type:0x1 card_type:0x1
Loading U-boot...success.
U-boot(odroidc@) (Jun 12 2015 - 17:31:14)
DRAM: 1 GiB
relocation Offset is: 2ff1c000
MMC: SDCARD: 0, eMMC: 1
IR init is done!
vpu clk_level =3D 3
set vpu clk: 182150000Hz, readback: 182150000Hz(0x701)
mode =3D 6 vic =3D 4
set HDMI vic: 4
mode is: 6
viu chan =3D 1
config HPLL
config HPLL done
reconfig packet setting done
MMC read: dev # 0, block # 33984, count 12288 ... 12288 blocks read: OK
There is no valid bmp file at the given address
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
Vendor: Man 035344 Snr 29cfee4e Rev: 8.0 Prod: SL08G
Type: Removable Hard Disk
Capacity: 7580.0 MB =3D 7.4 GB (15523840 x 512)
------------------------------------------------------------
Partition Start Sector Num Sectors Type
1 1134 131040 6
2 132174 15391666 a5
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D=
=3D=3D=3D=3D=3D=3D=3D=3D=3D=3D
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
Hit Enter key to stop autoboot -- : 0
exit abortboot: 0
reading boot.ini
98 bytes read
Loading boot.ini from mmc0:1 (vfat)
Executing the script...
setenv bootcmd "fatload mmc 0 0x100000 kernel.bin; go 0x100000"
run bootcmd
reading kernel.bin
6055396 bytes read
## Starting application at 0x00100000 ...
ARM Debug Architecture v7
2 watchpoints and 3 breakpoints supported
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights =
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #4 43026a8(master)-dirty: Thu Mar 31 04:14:32 CDT =
2016
=
root@dora:/usr/home/emoe/Projects/ARM/odroid-c1/obj/arm.armv6hf/usr/home/e=
moe/Projects/ARM/src/sys/ODROIDC1 arm
FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based on =
LLVM 3.8.0)
WARNING: WITNESS option enabled, expect reduced performance.
VT: init without driver.
Preloaded elf kernel "kernel" at 0xc07c5d6c.
CPU: Cortex A5 rev 1 (Cortex-A core)
Supported features: ARM_ISA THUMB2 JAZELLE THUMBEE ARMv4 Security_Ext
WB enabled LABT branch prediction disabled
LoUU:2 LoC:2 LoUIS:2
Cache level 1:
32KB/32B 4-way data cache WB Read-Alloc Write-Alloc
32KB/32B 2-way instruction cache Read-Alloc
real memory =3D 1073737728 (1023 MB)
avail memory =3D 1038233600 (990 MB)
Physical memory chunk(s):
0x00001000 - 0x3fffffff, 1023 MB ( 262143 pages)
Excluded memory regions:
0x00100000 - 0x00853fff, 7 MB ( 1876 pages) NoAlloc
Static device mappings:
0xc1100000 - 0xc12fffff mapped at VA 0xffd00000
0xc4200000 - 0xc42fffff mapped at VA 0xffc00000
0xc4300000 - 0xc43fffff mapped at VA 0xffb00000
0xc8000000 - 0xc80fffff mapped at VA 0xffa00000
0xc8100000 - 0xc81fffff mapped at VA 0xff900000
0xc9000000 - 0xc97fffff mapped at VA 0xff100000
0xd9000000 - 0xd90fffff mapped at VA 0xff000000
0xda000000 - 0xda0fffff mapped at VA 0xfef00000
Amlogic aml8726-m8b SoC
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
ULE: setup cpu 0
ULE: setup cpu 1
ULE: setup cpu 2
ULE: setup cpu 3
random: entropy device external interface
null: <full device, null device, zero device>
openfirm: <Open Firmware control device>
mem: <memory>
nfslock: pseudo-device
crypto: <crypto core>
random: harvesting attach, 8 bytes (4 bits) from nexus0
ofwbus0: <Open Firmware Device Tree>
simplebus0: <Flattened device tree simple bus> on ofwbus0
random: harvesting attach, 8 bytes (4 bits) from simplebus0
random: harvesting attach, 8 bytes (4 bits) from ofwbus0
clkmsr0: <Amlogic aml8726 clkmsr> mem 0xc1108758-0xc1108767 on =
simplebus0
clkmsr0: bus clock 159 MHz
random: harvesting attach, 8 bytes (4 bits) from clkmsr0
l2cache0: <PL310 L2 cache controller> mem 0xc4200000-0xc4200fff irq 0 on =
ofwbus0
l2cache0: Part number: 0x3, release: 0x9
l2cache0: L2 Cache enabled: 512KB/32B 8 ways
l2cache0: Early BRESP response: disabled
l2cache0: Instruction prefetch: disabled
l2cache0: Data prefetch: enabled
l2cache0: Non-secure interrupt control: disabled
l2cache0: Non-secure lockdown: disabled
l2cache0: Share override: disabled
l2cache0: Double linefill: disabled
l2cache0: Instruction prefetch: disabled
l2cache0: Data prefetch: enabled
l2cache0: Double linefill on WRAP request: disabled
l2cache0: Prefetch drop: disabled
l2cache0: Incr double Linefill: disabled
l2cache0: Not same ID on exclusive sequence: disabled
l2cache0: Prefetch offset: 0
random: harvesting attach, 8 bytes (4 bits) from l2cache0
scu0: <ARM Snoop Control Unit> mem 0xc4300000-0xc4300fff on simplebus0
random: harvesting attach, 8 bytes (4 bits) from scu0
cpuconfig0: <Amlogic CPU Config> mem 0xd901ff80-0xd901ff8f on simplebus0
random: harvesting attach, 8 bytes (4 bits) from cpuconfig0
ccm0: <Amlogic aml8726 ccm> mem 0xc1104140-0xc1104153 on simplebus0
random: harvesting attach, 8 bytes (4 bits) from ccm0
pinctrl0: <Amlogic aml8726 pinctrl> mem =
0xc11080b0-0xc11080d7,0xc11080e8-0xc11080ff,0xc1108120-0xc1108137,0xc81000=
14-0xc8100017,0xc810002c-0xc810002f,0xc810002c-0xc810002f on simplebus0
Processing 3 pin-config node(s) in pinctrl-0 for pinctrl@c11080b0
Processing 1 pin-config node(s) in pinctrl-0 for mmc@c1108c20
Processing 1 pin-config node(s) in pinctrl-0 for sdxc@c1108e00
random: harvesting attach, 8 bytes (4 bits) from pinctrl0
gic0: <ARM Generic Interrupt Controller> mem =
0xc4301000-0xc4301fff,0xc4300100-0xc43001ff on ofwbus0
ofwbus0: no default resources for rid =3D 0, type =3D 1
gic0: pn 0x390, arch 0x1, rev 0x1, implementer 0x43b irqs 256
random: harvesting attach, 8 bytes (4 bits) from gic0
wdt0: <Amlogic aml8726 WDT> mem 0xc1109900-0xc1109907 irq 2 on =
simplebus0
random: harvesting attach, 8 bytes (4 bits) from wdt0
timer0: <Amlogic aml8726 timer> mem 0xc1109940-0xc1109957 irq 1 on =
ofwbus0
Event timer "aml8726 timer A" frequency 1000000 Hz quality 1000
Timecounter "aml8726 timer E" frequency 1000000 Hz quality 1000
random: harvesting attach, 8 bytes (4 bits) from timer0
uart0: <Amlogic aml8726 UART> mem 0xc81004c0-0xc81004d7 irq 3 on =
simplebus0
uart0: RTS iflow, CTS oflow
uart0: console (115200,n,8,1)
uart0: fast interrupt
uart0: PPS capture mode: DCDinvalid
random: harvesting attach, 8 bytes (4 bits) from uart0
uart1: <Amlogic aml8726 UART> mem 0xc11084c0-0xc11084d7 irq 4 on =
simplebus0
uart1: RTS iflow, CTS oflow
uart1: fast interrupt
uart1: PPS capture mode: DCDinvalid
random: harvesting attach, 8 bytes (4 bits) from uart1
uart2: <Amlogic aml8726 UART> mem 0xc11084dc-0xc11084f3 irq 5 on =
simplebus0
uart2: RTS iflow, CTS oflow
uart2: fast interrupt
uart2: PPS capture mode: DCDinvalid
random: harvesting attach, 8 bytes (4 bits) from uart2
uart3: <Amlogic aml8726 UART> mem 0xc1108700-0xc1108717 irq 6 on =
simplebus0
uart3: RTS iflow, CTS oflow
uart3: fast interrupt
uart3: PPS capture mode: DCDinvalid
random: harvesting attach, 8 bytes (4 bits) from uart3
simplebus0: <i2c@c8100500> mem 0xc8100500-0xc810051f irq 7 disabled =
compat amlogic,meson6-i2c (no driver attached)
aml8726_iic0: <Amlogic aml8726 I2C> mem 0xc1108500-0xc110851f irq 8 on =
simplebus0
iicbb0: <I2C bit-banging driver> on aml8726_iic0
iicbus0: <Philips I2C bus> on iicbb0 master-only
iic0: <I2C generic I/O> on iicbus0
random: harvesting attach, 8 bytes (4 bits) from iic0
random: harvesting attach, 8 bytes (4 bits) from iicbus0
random: harvesting attach, 8 bytes (4 bits) from iicbb0
random: harvesting attach, 8 bytes (4 bits) from aml8726_iic0
aml8726_iic1: <Amlogic aml8726 I2C> mem 0xc11087c0-0xc11087df irq 9 on =
simplebus0
iicbb1: <I2C bit-banging driver> on aml8726_iic1
iicbus1: <Philips I2C bus> on iicbb1 master-only
iic1: <I2C generic I/O> on iicbus1
random: harvesting attach, 8 bytes (4 bits) from iic1
random: harvesting attach, 8 bytes (4 bits) from iicbus1
random: harvesting attach, 8 bytes (4 bits) from iicbb1
random: harvesting attach, 8 bytes (4 bits) from aml8726_iic1
simplebus0: <ir-receiver@c8100480> mem 0xc8100480-0xc810049f irq 10 =
disabled compat amlogic,meson6-ir (no driver attached)
simplebus0: <spi@c1108c80> mem 0xc1108c80-0xc1108cff disabled compat =
amlogic,meson6-spifc (no driver attached)
simplebus0: <ethernet@c9410000> mem =
0xc9410000-0xc941ffff,0xc1108108-0xc110810b irq 11 disabled compat =
amlogic,meson6-dwmac (no driver attached)
rtc0: <Amlogic aml8726 RTC> mem 0xc8100740-0xc8100753 irq 12 on =
simplebus0
rtc0: crystal oscillator check failed
device_attach: rtc0 attach returned 6
gpio0: <Amlogic aml8726 GPIO> mem =
0xc8100024-0xc8100027,0xc8100024-0xc8100027,0xc8100028-0xc810002b on =
simplebus0
gpiobus0: <OFW GPIO bus> on gpio0
gpioled0: <GPIO led> at pin 13 on gpiobus0
random: harvesting attach, 8 bytes (4 bits) from gpioled0
random: harvesting attach, 8 bytes (4 bits) from gpiobus0
gpioc0: <GPIO controller> on gpio0
random: harvesting attach, 8 bytes (4 bits) from gpioc0
random: harvesting attach, 8 bytes (4 bits) from gpio0
gpio1: <Amlogic aml8726 GPIO> mem =
0xc1108054-0xc1108057,0xc1108058-0xc110805b,0xc110805c-0xc110805f on =
simplebus0
gpiobus1: <OFW GPIO bus> on gpio1
random: harvesting attach, 8 bytes (4 bits) from gpiobus1
gpioc1: <GPIO controller> on gpio1
random: harvesting attach, 8 bytes (4 bits) from gpioc1
random: harvesting attach, 8 bytes (4 bits) from gpio1
gpio2: <Amlogic aml8726 GPIO> mem =
0xc110806c-0xc110806f,0xc1108070-0xc1108073,0xc1108074-0xc1108077 on =
simplebus0
gpiobus2: <OFW GPIO bus> on gpio2
random: harvesting attach, 8 bytes (4 bits) from gpiobus2
gpioc2: <GPIO controller> on gpio2
random: harvesting attach, 8 bytes (4 bits) from gpioc2
random: harvesting attach, 8 bytes (4 bits) from gpio2
aml8726_mmc0: <Amlogic aml8726 MMC> mem 0xc1108c20-0xc1108c3f irq 13 on =
simplebus0
mmc0: <MMC/SD bus> on aml8726_mmc0
random: harvesting attach, 8 bytes (4 bits) from mmc0
random: harvesting attach, 8 bytes (4 bits) from aml8726_mmc0
aml8726_sdxc0: <Amlogic aml8726-m8 SDXC> mem 0xc1108e00-0xc1108e3b irq =
14 on simplebus0
mmc1: <MMC/SD bus> on aml8726_sdxc0
random: harvesting attach, 8 bytes (4 bits) from mmc1
random: harvesting attach, 8 bytes (4 bits) from aml8726_sdxc0
simplebus0: <rng@c1108100> mem 0xc1108100-0xc1108107 compat =
amlogic,aml8726-rng (no driver attached)
usbphy0: <Amlogic aml8726-m8 USB PHY> mem 0xc1108800-0xc110881f on =
simplebus0
random: harvesting attach, 8 bytes (4 bits) from usbphy0
usbphy1: <Amlogic aml8726-m8 USB PHY> mem 0xc1108820-0xc110883f on =
simplebus0
random: harvesting attach, 8 bytes (4 bits) from usbphy1
dwcotg0: <DWC OTG 2.0 integrated USB controller> mem =
0xc9040000-0xc907ffff irq 15 on simplebus0
usbus0 on dwcotg0
dwcotg0: usbpf: Attached
random: harvesting attach, 8 bytes (4 bits) from usbus0
random: harvesting attach, 8 bytes (4 bits) from dwcotg0
dwcotg1: <DWC OTG 2.0 integrated USB controller> mem =
0xc90c0000-0xc90fffff irq 16 on simplebus0
usbus1 on dwcotg1
dwcotg1: usbpf: Attached
random: harvesting attach, 8 bytes (4 bits) from usbus1
random: harvesting attach, 8 bytes (4 bits) from dwcotg1
dwc0: <Amlogic Meson Gigabit Ethernet Controller> mem =
0xc9410000-0xc9411fff irq 11 on simplebus0
miibus0: <MII bus> on dwc0
rgephy0: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 0 on =
miibus0
rgephy0: OUI 0x00e04c, model 0x0011, rev. 6
rgephy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, =
1000baseT-FDX, 1000baseT-FDX-master, auto
random: harvesting attach, 8 bytes (4 bits) from rgephy0
rgephy1: <RTL8169S/8110S/8211 1000BASE-T media interface> PHY 1 on =
miibus0
rgephy1: OUI 0x00e04c, model 0x0011, rev. 6
rgephy1: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, =
1000baseT-FDX, 1000baseT-FDX-master, auto
random: harvesting attach, 8 bytes (4 bits) from rgephy1
random: harvesting attach, 8 bytes (4 bits) from miibus0
dwc0: bpf attached
dwc0: Ethernet address: 62:73:64:5d:6a:ec
random: harvesting attach, 8 bytes (4 bits) from dwc0
fb0: <Amlogic aml8726 FB> mem =
0xc8006048-0xc8006053,0xc1106800-0xc1106bff,0xc1107400-0xc11077ff irq =
17,18,19,20 on simplebus0
fbd0 on fb0
VT: initialize with new VT driver "fb".
random: harvesting attach, 8 bytes (4 bits) from fbd0
random: harvesting attach, 8 bytes (4 bits) from fb0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpu0: missing 'clock-frequency' property
random: harvesting attach, 8 bytes (4 bits) from cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpu1: missing 'clock-frequency' property
random: harvesting attach, 8 bytes (4 bits) from cpu1
cpu2: <Open Firmware CPU> on cpulist0
cpu2: missing 'clock-frequency' property
random: harvesting attach, 8 bytes (4 bits) from cpu2
cpu3: <Open Firmware CPU> on cpulist0
cpu3: missing 'clock-frequency' property
random: harvesting attach, 8 bytes (4 bits) from cpu3
random: harvesting attach, 8 bytes (4 bits) from cpulist0
ofwbus0: <clk@0> compat fixed-clock (no driver attached)
ofwbus0: <leds> compat gpio-leds (no driver attached)
cryptosoft0: <software crypto>
crypto: assign cryptosoft0 driver id 0, flags 100663296
crypto: cryptosoft0 registers alg 1 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 2 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 3 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 4 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 5 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 16 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 6 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 7 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 18 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 19 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 20 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 8 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 15 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 9 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 10 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 13 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 14 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 11 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 22 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 23 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 25 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 24 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 26 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 27 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 28 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 21 flags 0 maxoplen 0
crypto: cryptosoft0 registers alg 17 flags 0 maxoplen 0
random: harvesting attach, 8 bytes (4 bits) from cryptosoft0
procfs registered
Timecounters tick every 10.000 msec
tcp_init: net.inet.tcp.tcbhashsize auto tuned to 8192
usbus0: 480Mbps High Speed USB v2.0
IPsec: Initialized Security Association Processing.
lo0: bpf attached
mmc0: Probing bus
usbus1: 480Mbps High Speed USB v2.0
mmc0: SD 2.0 interface conditions: OK
mmc0: SD probe: OK (OCR: 0x40ff8000)
mmc0: Current OCR: 0x00ff8000
ugen1.1: <DWCOTG> at usbus1
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
ugen0.1: <DWCOTG> at usbus0
uhub1: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
mmc0: Probing cards
mmc0: New card detected (CID 035344534c3038478029cfee4e00f900)
mmc0: New card detected (CSD 400e00325b5900003b377f800a404000)
mmc0: Card at relative address 0xaaaa added:
mmc0: card: SDHC SL08G 8.0 SN 29CFEE4E MFG 09/2015 by 3 SD
mmc0: bus: 4bit, 50MHz, high speed timing
mmc0: memory: 15523840 blocks, erase sector 8192 blocks
mmc0: setting transfer rate to 39.750MHz (high speed timing)
mmcsd0: 8GB <SDHC SL08G 8.0 SN 29CFEE4E MFG 09/2015 by 3 SD> at mmc0 =
39.7MHz/4bit/8-block
random: harvesting attach, 8 bytes (4 bits) from mmcsd0
mmc1: Probing bus
GEOM: new disk mmcsd0
mmc0: setting bus width to 4 bits
GEOM_PART: partition 1 on (mmcsd0, MBR) is not aligned on 4194304 bytes
GEOM_PART: partition 2 on (mmcsd0, MBR) is not aligned on 4194304 bytes
mmc1: SD probe: failed
mmc1: MMC probe: failed
mmc1: Current OCR: 0x00000000
mmc1: No compatible cards found on bus
Release APs
WARNING: WITNESS option enabled, expect reduced performance.
Trying to mount root from ufs:mmcsd0s2 []...
GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 =
bytes
GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned on =
4194304 bytes
GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned on =
4194304 bytes
GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not aligned =
on 4194304 bytes
warning: no time-of-day clock registered, system time will not be set =
accurately
start_init: trying /sbin/init
uhub0: 1 port with 1 removable, self powered
random: harvesting attach, 8 bytes (4 bits) from uhub0
uhub1: 1 port with 1 removable, self powered
random: harvesting attach, 8 bytes (4 bits) from uhub1
ugen1.2: <vendor 0x05e3> at usbus1
uhub2: <vendor 0x05e3 USB2.0 Hub, class 9/0, rev 2.00/32.98, addr 2> on =
usbus1
uhub2: MTT enabled
Growing root partition to fill device
GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned on =
4194304 bytes
GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned on =
4194304 bytes
GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not aligned =
on 4194304 bytes
mmcsd0s2 resized
growfs: superblock not recognized
/etc/rc: WARNING: hostid: unable to figure out a UUID from DMI data, =
generating a new one
uhub2: 4 ports with 4 removable, self powered
random: harvesting attach, 8 bytes (4 bits) from uhub2
Setting hostuuid: 214610b1-f72e-11e5-8203-df073412266c.
Setting hostid: 0x373425ad.
No suitable dump device was found.
Starting file system checks:
/dev/mmcsd0s2: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/mmcsd0s2: clean, 36687 free (103 frags, 4573 blocks, 0.0% =
fragmentation)
GEOM_PART: partition 1 on (mmcsd0s2, BSD) is not aligned on 4194304 =
bytes
GEOM_PART: partition 1 on (diskid/DISK-29CFEE4E, MBR) is not aligned on =
4194304 bytes
GEOM_PART: partition 2 on (diskid/DISK-29CFEE4E, MBR) is not aligned on =
4194304 bytes
GEOM_PART: partition 1 on (diskid/DISK-29CFEE4Es2, BSD) is not aligned =
on 4194304 bytes
Mounting local file systems:.
Setting hostname: freebsd.
Setting up =
harvesting:[UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,NET_ETHER,NET_TUN,MOUSE,K=
EYBOARD,ATTACH,CACHED
Feeding entropy:random: unblocking device.
.
dwc0: link state changed to DOWN
Starting Network: lo0 dwc0.
lo0: flags=3D8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
options=3D600003<RXCSUM,TXCSUM,RXCSUM_IPV6,TXCSUM_IPV6>
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2
inet 127.0.0.1 netmask 0xff000000
groups: lo
nd6 options=3D21<PERFORMNUD,AUTO_LINKLOCAL>
dwc0: flags=3D8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu =
1500
options=3D80008<VLAN_MTU,LINKSTATE>
ether 62:73:64:5d:6a:ec
media: Ethernet autoselect (none)
status: no carrier
nd6 options=3D29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL>
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
Starting devd.
add net fe80::: gateway ::1
add net ff02::: gateway ::1
add net ::ffff:0.0.0.0: gateway ::1
add net ::0.0.0.0: gateway ::1
Generating host.conf.
Waiting 30s for the default route interface: .....(no carrier)
Creating and/or trimming log files.
Starting syslogd.
Clearing /tmp (X related).
Updating motd:.
Mounting late file systems:.
Configuring vt: blanktime.
Generating RSA host key.
2048 SHA256:efid4fCpKZlmdi69b18qj+SNx2mSPQNr6ourB/w9tPw root@freebsd =
(RSA)
Generating ECDSA host key.
256 SHA256:bpBVM0B9a3xDhmy3bvoC4OuELAJ4fvJd+p3tNwgia6k root@freebsd =
(ECDSA)
Generating ED25519 host key.
256 SHA256:VHMKoDA1Zv50CmxiLJwTIvg58S2DuBg6zj2VFXDGq/M root@freebsd =
(ED25519)
Performing sanity check on sshd configuration.
Could not load host key: /etc/ssh/ssh_host_dsa_key
Starting sshd.
Could not load host key: /etc/ssh/ssh_host_dsa_key
Starting cron.
Starting background file system checks in 60 seconds.
lock order reversal:
1st 0xc4499814 ufs (ufs) @ =
/usr/home/emoe/Projects/ARM/src/sys/kern/vfs_subr.c:2498
2nd 0xd90169a0 bufwait (bufwait) @ =
/usr/home/emoe/Projects/ARM/src/sys/ufs/ffs/ffs_vnops.c:263
3rd 0xc45c15d4 ufs (ufs) @ =
/usr/home/emoe/Projects/ARM/src/sys/kern/vfs_subr.c:2498
stack backtrace:
mount: /dev/mmcsd0s2: Device busy
Thu Mar 31 10:49:29 UTC 2016
FreeBSD/arm (freebsd) (ttyu0)
login:
> On Mar 30, 2016, at 7:47 PM, Erik Moe <e.moe@rcn.com> wrote:
>=20
> I was able to build a working odroid-c1 image not too long ago. Let =
me pull the latest sources and see if something has changed.
>=20
> Erik=20
>=20
>> On Mar 30, 2016, at 2:24 AM, Daniel Braniss <danny@cs.huji.ac.il> =
wrote:
>>=20
>> Hi,
>> Managed to make a bootable SD, cross compile world/kernel,
>> but the kernel startup gets stuck, I can=E2=80=99t even get into the =
debugger.
>> any help/hints most welcome :-)
>> btw, I can also boot via the network, cutting down the debug cycle =
considerably.
>> thanks,
>> danny
>> PS: here is the console output
>> <s1>
>> _______________________________________________
>> freebsd-arm@freebsd.org mailing list
>> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
>> To unsubscribe, send any mail to =
"freebsd-arm-unsubscribe@freebsd.org"
> _______________________________________________
> freebsd-arm@freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe@freebsd.org"
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?B39CD871-7BE5-44EA-816A-42A80E34D8A7>