Date: Mon, 13 Nov 2006 07:24:46 +0100 From: Zoran Kolic <zkolic@sbb.co.yu> To: Aleksandra Brzezi?ska <aleksandra.brzezinska@unixy.pl> Cc: freebsd-mobile@freebsd.org Subject: Re: Too hot temperature of disk - HP Compaq nc6220 Message-ID: <20061113062446.GA632@faust.net> In-Reply-To: <1163349851.3968.14.camel@ola.pl> References: <20061112120058.568CF16A6C8@hub.freebsd.org> <20061112142233.GA638@faust.net> <1163349851.3968.14.camel@ola.pl>
next in thread | previous in thread | raw e-mail | index | archive | help
> debug.acpi.do_powerstate: 1
> hw.acpi.supported_sleep_state: S3 S4 S5
> hw.acpi.power_button_state: S5
> hw.acpi.sleep_button_state: S3
> hw.acpi.lid_switch_state: NONE
> hw.acpi.standby_state: S1
> hw.acpi.suspend_state: S3
> hw.acpi.sleep_delay: 1
> hw.acpi.s4bios: 1
> hw.acpi.verbose: 0
> hw.acpi.reset_video: 1
> hw.acpi.cpu.cx_supported: C1/1 C2/2 C3/38
I have set in rc.conf:
performance_cx_lowest="LOW"
economy_cx_lowest="LOW"
> hw.acpi.cpu.cx_lowest: C1
> hw.acpi.cpu.cx_usage: 100.00% 0.00% 0.00%
Above options wuold change this.
> hw.acpi.thermal.tz0.temperature: 59.0C
A little bit high.
> hw.acpi.thermal.tz0.active: 2
> hw.acpi.thermal.tz0.passive_cooling: 1
> hw.acpi.thermal.tz0.thermal_flags: 0
> hw.acpi.thermal.tz0._PSV: 100.0C
> hw.acpi.thermal.tz0._HOT: -1
> hw.acpi.thermal.tz0._CRT: 105.0C
> hw.acpi.thermal.tz0._ACx: 80.0C 70.0C 55.0C 35.0C -1 -1 -1 -1 -1 -1
> hw.acpi.thermal.tz1.temperature: 45.0C
> hw.acpi.thermal.tz1.active: -1
> hw.acpi.thermal.tz1.passive_cooling: 0
> hw.acpi.thermal.tz1.thermal_flags: 0
> hw.acpi.thermal.tz1._PSV: -1
> hw.acpi.thermal.tz1._HOT: -1
> hw.acpi.thermal.tz1._CRT: 103.0C
> hw.acpi.thermal.tz1._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
> hw.acpi.thermal.tz2.temperature: 16.0C
> hw.acpi.thermal.tz2.active: -1
> hw.acpi.thermal.tz2.passive_cooling: 0
> hw.acpi.thermal.tz2.thermal_flags: 0
> hw.acpi.thermal.tz2._PSV: 60.0C
> hw.acpi.thermal.tz2._HOT: -1
> hw.acpi.thermal.tz2._CRT: 105.0C
> hw.acpi.thermal.tz2._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1
>
> I loaded cpufreq.ko (default, without any compilation), effect:
> ola# kldload cpufreq
I have it in kernel.
And in rc.conf:
powerd_enable="YES"
> est0: <Enhanced SpeedStep Frequency Control> on cpu0
> est: CPU supports Enhanced Speedstep, but is not recognized.
> est: Please update driver or contact the maintainer.
> est: cpu_vendor GenuineIntel, msr 6120e2906000e29, bus_clk, 64
> device_attach: est0 attach returned 6
I've put in /boot/loader.conf:
hint.ichss.0.disabled="1"
Best regards
Zoran
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?20061113062446.GA632>