Date: Fri, 16 Apr 1999 23:57:29 +1000 (EST) From: Andrew McRae <amcrae@cisco.com> To: freebsd-smp@freebsd.org, freebsd-hardware@freebsd.org Subject: SMP kernel on SuperMicro P6DBE Message-ID: <199904161357.XAA15234@ringer.cisco.com>
next in thread | raw e-mail | index | archive | help
Comrades,
I have swapped in a Supermicro P6DBE dual PII motherboard
and am attempting to run FreeBSD current on it. I originally
installed two 350MHz PIIs, and booted a prebuilt SMP kernel.
It ran fine for a few minutes, long enough for me to start
X, run netscape etc., and then it hung. After a few seconds
it rebooted. Checking the SMP web details, I tried a kernel
with SMP_TIMER_NC, but the same occurred. I removed one
of the PIIs, and it works just fine with only one CPU.
Are there any known issues with this motherboard?
Is there anything I should try to counter this problem?
I have attached boot messages and the output of mptable.
Cheers,
Andrew McRae (amcrae@cisco.com)
Boot messages are:
Copyright (c) 1992-1999 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
FreeBSD 4.0-CURRENT #2: Fri Apr 16 22:29:25 EST 1999
amcrae@sporran:/home/amcrae/perforce/usr/src/sys/compile/SMP-SPORRAN
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Xeon/Celeron (686-class CPU)
Origin = "GenuineIntel" Id = 0x652 Stepping=2
Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CM
OV,PAT,PSE36,MMX,FXSR>
real memory = 67108864 (65536K bytes)
avail memory = 62521344 (61056K bytes)
Programming 24 pins in IOAPIC #0
WARNING: Failed to start all APs
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00040011, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x00170011, at 0xfec00000
Preloaded elf kernel "kernel" at 0xc02b8000.
Pentium Pro MTRR support enabled, default memory type is uncacheable
Probing for devices on PCI bus 0:
chip0: <Intel 82443BX host to PCI bridge> rev 0x02 on pci0.0.0
chip1: <Intel 82443BX host to AGP bridge> rev 0x02 on pci0.1.0
chip2: <Intel 82371AB PCI to ISA bridge> rev 0x02 on pci0.7.0
ide_pci0: <Intel PIIX4 Bus-master IDE controller> rev 0x01 on pci0.7.1
chip3: <Intel 82371AB Power management controller> rev 0x02 on pci0.7.3
vga0: <S3 ViRGE DX/GX graphics accelerator> rev 0x01 int a irq 17 on pci0.16.0
ncr0: <ncr 53c875j fast20 wide scsi> rev 0x04 int a irq 18 on pci0.18.0
Probing for devices on PCI bus 1:
Probing for PnP devices:
Probing for devices on the ISA bus:
sc0 on isa
sc0: VGA color <16 virtual consoles, flags=0x0>
ed0 at 0x300-0x31f irq 10 maddr 0xd8000 msize 16384 on isa
ed0: address 00:00:c0:f9:e1:8a, type WD8013WC (16 bit)
atkbdc0 at 0x60-0x6f on motherboard
sio0 at 0x3f8-0x3ff irq 4 on isa
sio0: type 16550A
sio1 at 0x2f8-0x2ff irq 3 on isa
sio1: type 16550A
fdc0 at 0x3f0-0x3f7 irq 6 drq 2 on isa
fdc0: FIFO enabled, 8 bytes threshold
fd0: 1.44MB 3.5in
wdc0 not found at 0x1f0
ppc0 at 0x378 irq 7 on isa
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppb0: IEEE1284 device found /NIBBLE/ECP
Probing for PnP devices on ppbus0:
ppbus0: <HEWLETT-PACKARD DESKJET 670C> MLC,PCL,PML
lpt0: <generic printer> on ppbus 0
lpt0: Interrupt-driven port
vga0 at 0x3b0-0x3df maddr 0xa0000 msize 131072 on isa
npx0 on motherboard
npx0: INT 16 interface
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via pin 2
Waiting 2 seconds for SCSI devices to settle
sa0 at ncr0 bus 0 target 4 lun 0
sa0: <EXABYTE EXB-8500SMBANXH1 046G> Removable Sequential Access SCSI-2 device
sa0: 4.032MB/s transfers (4.032MHz, offset 11)
cd0 at ncr0 bus 0 target 6 lun 0
cd0: <PIONEER CD-ROM DR-U06S 1.05> Removable CD-ROM SCSI-2 device
cd0: 19.230MB/s transfers (19.230MHz, offset 16)
cd0: Attempt to query device size failed: NOT READY, Medium not present
da0 at ncr0 bus 0 target 1 lun 0
da0: <IBM DDRS-34560W S71D> Fixed Direct Access SCSI-2 device
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing Enabled
da0: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
changing root device to da0s4a
mptable tells me:
===============================================================================
MPTable, version 2.0.15
-------------------------------------------------------------------------------
MP Floating Pointer Structure:
location: BIOS
physical address: 0x000fb500
signature: '_MP_'
length: 16 bytes
version: 1.1
checksum: 0x5b
mode: Virtual Wire
-------------------------------------------------------------------------------
MP Config Table Header:
physical address: 0x000f69d0
signature: 'PCMP'
base table length: 248
version: 1.1
checksum: 0xa9
OEM ID: 'INTEL '
Product ID: '440BX '
OEM table pointer: 0x00000000
OEM table size: 0
entry count: 24
local APIC address: 0xfee00000
extended table length: 0
extended table checksum: 0
-------------------------------------------------------------------------------
MP Config Base Table Entries:
--
Processors: APIC ID Version State Family Model Step Flags
0 0x11 BSP, usable 6 5 2 0x183fb
ff
--
Bus: Bus ID Type
0 PCI
1 PCI
2 ISA
--
I/O APICs: APIC ID Version State Address
2 0x11 usable 0xfec00000
--
I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 2 0 2 0
INT conforms conforms 2 1 2 1
INT conforms conforms 2 0 2 2
INT conforms conforms 2 3 2 3
INT conforms conforms 2 4 2 4
INT conforms conforms 2 5 2 5
INT conforms conforms 2 6 2 6
INT conforms conforms 2 7 2 7
INT active-hi edge 2 8 2 8
INT conforms conforms 2 10 2 10
INT conforms conforms 2 12 2 12
INT conforms conforms 2 13 2 13
INT conforms conforms 2 14 2 14
INT active-lo level 2 11 2 17
INT active-lo level 2 9 2 18
INT active-lo level 2 15 2 19
SMI conforms conforms 2 0 2 23
--
Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
ExtINT conforms conforms 0 0:A 255 0
NMI conforms conforms 0 0:A 255 1
-------------------------------------------------------------------------------
# SMP kernel config file options:
# Required:
options SMP # Symmetric MultiProcessor Kernel
options APIC_IO # Symmetric (APIC) I/O
# Optional (built-in defaults will work in most cases):
#options NCPU=1 # number of CPUs
#options NBUS=3 # number of busses
#options NAPIC=1 # number of IO APICs
#options NINTR=24 # number of INTs
===============================================================================
To Unsubscribe: send mail to majordomo@FreeBSD.org
with "unsubscribe freebsd-hardware" in the body of the message
Want to link to this message? Use this URL: <https://mail-archive.FreeBSD.org/cgi/mid.cgi?199904161357.XAA15234>